WOHUA S820 Remote Control Boat Instruction Manual
- July 6, 2024
- WOHUA
Table of Contents
WOHUA S820 Remote Control Boat
Product Information
Specifications:
- Compliance : FCC Part 15
- Radiation Exposure Limits: FCC compliant for an uncontrolled environment
- Minimum Distance: 0cm between radiator and body
Product Usage Instructions
Safety Precautions:
- Do not make any changes or modifications to the device that are not approved by the manufacturer.
- Ensure that the device is operated in compliance with FCC Rules.
- Maintain a minimum distance of 0cm between the radiator of the device and your body during operation.
Installation:
- Place the device on a stable surface away from water or other liquids.
- Connect the device to a power source as per the manufacturer’s instructions.
Operation:
- Power on the device using the designated power button.
- Follow the specific instructions provided in the user manual for desired functionality.
Maintenance:
- Regularly clean the device with a soft, dry cloth to prevent dust buildup.
- Avoid exposing the device to extreme temperatures or direct sunlight.
Remote control and boat operation
Remote control button function:
- Turn on the remote control. Put the hull into the water and activate the power supply to complete the frequency matching.
- When the forward/backward button is pressed, the ship can move forward/backward.
- When pressing the forward button and holding down the left/right turn button at the same time, the ship can advance left/right turn.
- Press the left button separately, and the ship will rotate in place in the left direction. Press the right turn button alone, and the boat will rotate in place in the right direction.
- When the left fine-tuning/right fine-tuning button is pressed, the straight-line driving performance of the ship can be adjusted.
Charging method
Unplug the charging cable cover and plug in the charging cable to charge. The lights on the hull will light up during charging, and the lights will go off when the battery is fully charged.
Electrification method
When using, first turn on the power switch of the remote control, and then Put it into the water, the contact point touches the water source, and the hull is energized. In the process of linking, after the linking is completed, the indicator light stays on.
Notice : Do not put your hands near the propeller to prevent the propeller from rotating at high speed to injure people and make sure there are no obstacles around the propeller.
if When stopping use, please take the boat out of the water, wipe it dry with a cloth, and put it away. Good. After the boat leaves the water and is dried, it will be in a power-off state. The boat propeller stopped spinning.
Accessories installation
put decorative pieces Installation on the hull ( as the picture shows)
FCC
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection againstharmful interference in a residential installation. This equipment generates, uses, and can radiateradio frequency energy and, if not installed and used in accordance with the instructions, maycause harmful interference to radio communications. However, there is no guarantee thatinterference will not occur in a particular installation. If this equipment does cause harmfulinterferenc e to radio or television reception, which can be determined by turning the equipmentoff and on, the user is encouraged to try to correct the interference by one or more of thefollowing measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Caution : Any changes or modifications to this device not explicitly approved by the manufacturer could void your authority to operate this equipment.
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 0cm between the radiator and your body.
FAQ
Q: Can I modify the device for enhanced performance?
A: No, any changes or modifications not approved by the manufacturer may void
your warranty and authority to operate the equipment.
Q: What should I do if the device causes interference?
A: If interference occurs, try repositioning the device. If issues persist,
contact customer support for assistance.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>