wet sounds ZERO SUB ENC Roto Mold Enclosure Subwoofer User Manual
- July 6, 2024
- wet sounds
Table of Contents
wet sounds ZERO SUB-ENC Roto Mold Enclosure Subwoofer
Specifications:
- ZERRO 110 ENC: Width: 14″ (355.60 mm), Length: 18″ (457.20 mm), Front Height: 5.71″ (145.03 mm), Rear Height: 8.81″ (223.77 mm)
- ZERRO 112 ENC: Width: 14″ (355.60 mm), Length: 28″ (711.20 mm), Front Height: 5.71″ (145.03 mm), Rear Height: 8.81″ (223.77 mm)
Product Usage Instructions
Install Guide
For use with ZERRO 1100 or ZERRO 1122 Subwoofers.
- Connect the subwoofer signal leads and install the subwoofer into the enclosure using the provided hardware.
- Secure the sub from the bottom side of the enclosure using the M6x20mm bolt provided.
- Connect your signal leads to the 2-pin drymate connector provided and plug the connector into the bulkhead connection on the rear of the enclosure.
- Using the provided Mounting Plates (x2) and #8 Phillips Screws (x4), secure the enclosure. Note that the enclosure can be mounted horizontally or vertically.
- The enclosures can be joined together when running multiple subs. Prior to installing the subwoofers, place the spacer block insert into the side pocket of the enclosure. Drill 2 holes through the side of the enclosures that will be joined. Join the enclosures together using the spacer block insert and bolt the enclosures using the provided hardware.
Thank you for purchasing Wet Sounds™ High Performance Audio Products!
Wet Sounds products represent the ultimate in high performance audio. Wet
Sounds products are specifically engineered to withstand rigorous marine
environments. Please take a moment to read the instruction manual before
starting your installation. This guide will explain the benefits of the
technologies developed by Wet Sounds and will help you understand the correct
installation methods and use of this product. If you have any questions or
concerns, please contact a certified Wet Sounds dealer. You may also contact
Wet Sounds technical support by dialing 1-877-WETSPKR
(1-877-938-7757).
Included
Included but not shown:
- x1 Internal Harness
- x2 M5 Steel Washers
- x2 M5 Steel Hex Nuts
- ×2 #4 Phillips Screws
- x2 M5x0.8x55mm Long Steel Socket Head Screw
- x1 M6x1x20mm Long Steel Socket Head Screw
- x1 Wire Harness Pigtail
DIMENSION
For use with ZERO 10 or ZERO 12 Subwoofers.
Installation
Limited Warranty
- What This Warranty Covers: This is a “limited” warranty. This warranty covers any defect in materials and workmanship. This warranty only covers the original purchaser and is not transferable. This warranty is also only valid if the original purchase was made from an authorized Wet Sounds TM dealer.
- How Long Coverage Lasts: This warranty extends for 2 years from the date of purchase. It is recommended to REGISTER your warranty online within 45 days of purchase at www.wetsounds.com – click on “warranty registration”.
- What Is Not Covered: This warranty does not cover fading or discoloration caused by exposure to sunlight or chemicals such as ammonia, household bleach, or any cleaning material that contains abrasive substances. Wet Sounds, Inc. does not cover the expense for removal or re-installation. Additionally, shipping TO Wet Sounds, Inc. must be paid for by the purchaser. This warranty is void and inapplicable is Wet Sounds deems that the product was abused or misused; including but not limited to damage caused by accident, mishandling, improper installation, removing the inline fuse on the power connection, negligence, normal; wear and tear, excessive water or heat damage, freight/shipping damage, or products that have been disassembled by anyone other than Wet Sounds technical staff. Wet Sounds will not be responsible for any incidental or consequential damages, except to the extent provided (or prohibited) by applicable law. This warranty gives you specific rights, and you may also have other rights which vary from state to state. This warranty does not cover fading or discoloration caused by exposure to sunlight or chemicals such as ammonia, household bleach, or any cleaning material that contains abrasive substances. Wet Sounds, Inc. does not cover the expense for removal or • re-installation. Additionally, shipping TO Wet Sounds, Inc. must be paid for by the purchaser. This warranty is void and inapplicable is Wet Sounds deems that the product was abused or misused; including but not limited to damage caused by accident, mishandling, improper installation, removing the inline fuse on the power connection, negligence, normal; wear and tear, excessive water or heat damage, freight/shipping damage, or products that have been disassembled by anyone other than Wet Sounds technical staff. Wet Sounds will not be responsible for any incidental or consequential damages, except to the extent provided (or prohibited) by applicable law. This warranty gives you specific rights, and you may also have other rights which vary from state to state.
- What Wet Sounds, Inc. Will Do : Wet Sounds, Inc. will repair any part of your product that proves to be defective in materials or workmanship. In the event repair is not possible, Wet Sounds will replace the product in question. If it is deemed necessary Wet Sounds, Inc. will either replace the entire product with a refurbished unit or it will be replaced with a model that is similar in price is that model is no longer available. Labor costs and materials needed to complete this service will be at No Charge to the purchaser. Additionally, return shipping FROM Wet Sounds, Inc. to the purchaser will be paid for by Wet Sounds.
- How To Get Service: Contact Wet Sounds, Inc. either by phone (877-938-7757) or by email (warranty@wetsounds.com). A service representative will assist you in confirming that the problem you are experiencing is caused by a defective product and if that product is covered under warranty. The service representative will issue you a Return Manufacturer’s Authorization (RMA) and other details to obtain service for your product.
- How To Get Service : Contact Wet Sounds, Inc. either by phone (877-938-7757) or by email (warranty@wetsounds.com). A service representative will assist you in confirming that the problem you are experiencing is caused by a defective product and if that product is covered under warranty. The service representative will issue you a Return Manufacturer’s Authorization (RMA) and other details to obtain service for your product.
- DO NOT RETURN YOUR PRODUCT WITHOUT THE PROPER RETURN AUTHORIZATION (RMA)!
Internet Warning: Wet Sounds, Inc. products sold on any non-authorized web site or internet auction site are void of any and all manufacturer’s warranty. Please contact Wet Sounds (877- 938-7757) or visit our website (www.wetsounds.com) for a list of authorized online sellers or to find an authorized installing retailer near you.
Wet Sounds, Inc.
- 877-938-7757
- www.wetsounds.com
- 2975 Louise Street
- Rosenberg, Texas 77471 USA
© 2023 Wet Sounds, Inc. All Rights Reserved. WET SOUNDS and associated logos where applicable are registered trademarks of Wet Sounds Corporation in the United States and/or other countries. All other trademarks are the property of their respective owners.
FAQ
Q: Can I mount the enclosure vertically?
A: Yes, the enclosure can be mounted both horizontally and vertically.
Q: How do I connect multiple subs together?
A: To connect multiple subs, place the spacer block insert into the side
pocket of each enclosure, drill holes through the sides that will be joined,
and bolt them together using the provided hardware.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>