SINGER 4432 Heavy Duty Sewing Machine Instruction Manual

SINGER 4432 Heavy Duty Sewing Machine

IMPORTANT SAFETY INSTRUCTIONS

When using an electrical appliance, basic safety should always be followed, including the following:
Read all instructions before using this sewing machine.

DANGER
To reduce the risk of electric shock:

1. An appliance should never be left unattended when plugged in.
2. Always unplug this appliance from the electric outlet immediately after using and before cleaning.
3. The LED lamp maximum power is 0.3W, maximum voltage is DC 9V. If the lamp is damaged, you should not use the product, send it to SINGER or a service agent to repair or replace at once.

WARNING – To reduce the risk of burns, fire, electric shock, or injury to persons:

1. Do not allow to be used as a toy. Close attention is necessary when this appliance is used by or near children.
2. Use this appliance only for its intended use as described in this manual. Use only attachments recommended by the manufacturer as contained in this manual.
3. ever operate this appliance if it has a damaged cord or plug, if it is not working properly, if it has been dropped or damaged, or dropped into water. Return the appliance to the nearest authorized dealer or service center for examination, repair, Center for examination, rapes electrical or mechanical adjustment.
4. Never operate the appliance with any air openings blocked. Keep ventilation openings of the sewing machine and foot controller free from accumulation of lint, dust, and loose cloth. 5. Keep fingers away from all moving parts. Special care is required around the sewing machine needle.
5. Always use the proper needle plate. The wrong plate can cause the needle to break.
6. Do not use bent needles.
7. Do not pull or push fabric while stitching. It may deflect the needle causing it to break.
8. Switch the sewing machine off (“O”) when making any adjustments in the needle area, such as threading needle, changing needle, threading bobbin, or changing presser foot, and the like.
9. Always unplug sewing machine from the electrical outlet when removing covers, lubricating, or when making any other user servicing adjustments mentioned in the instruction manual.
10. Never drop or insert any object into any opening.
11. Do not use outdoors.
12. Do not operate where aerosol spray products are being used or where oxygen is being administered.
13. To disconnect, turn all controls to the off (“O”) position, then remove plug from outlet.
14. Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.
15. The sound pressure level under normal operating conditions is 75dB(A).
16. Please turn off the machine or unplug when the machine is not operating properly.
17. ever place anything on the foot controller.
18. If the supply cord that is fixed with foot controller is damaged, it must be replaced by the manufacturer or its service agent or a similar qualified person in order to avoid a hazard.
19. This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
20. Children should be supervised to ensure that they do not play with the appliance.
    SAVE THESE INSTRUCTIONS
    This sewing machine is intended for household use only.

Congratulations
As the owner of a new SINGER sewing machine, you are about to begin an exciting adventure in creativity. From the moment you first use your machine, you will know you are sewing on one of the easiest to use sewing machines ever made.
May we recommend that, before you start to use your sewing machine, you discover the many features and the ease of operation by going through this instruction book, step by step, seated at your machine.
To ensure that you are always provided with the most modern sewing capabilities, the manufacturer reserves the right to change the appearance, design or accessories of this sewing machine when considered necessary. SINGER is the exclusive trademark of The Singer Company Limited S.à.r.l. or its Affiliates. ©2013 The Singer Company Limited S.à.r.l. or its Affiliates. All rights reserved.

Principal Parts of the Machine

1. Thread tension dial
2. Presser foot pressure adjustment
3. Thread take-up lever
4. Reverse sewing lever
5. Thread cutter
6. Presser foot
7. Needle plate cover
8. Removable extension table/ accessory storage
9. Three-needle position dial
10. Bobbin stopper
11. Stitch width dial
12. Stitch length dial
13. Pattern selector dial
14. Automatic threader
15. One step buttonhole lever
16. Horizontal spool pin
17. Bobbin winding spindle
18. Hole for auxiliary spool pin
19. Handwheel
20. Buttonhole stitch balance adjustment slot
21. Power and light switch
22. Main plug socket
23. Bobbin thread guide
24. Upper thread guide
25. Face plate
26. Handle
27. Presser foot lifter
28. Drop feed control
29. Foot speed control
30. Power cord

Connecting Machine to Power Source

Connect the machine to a power source as illustrated. (1)
This appliance is equipped with a polarized plug which must be used with the appropriate polarized outlet. (2)
Attention:
Unplug the power cord when the machine is not in use.
Foot control
The foot control pedal regulates the sewing speed. (3)
Attention:
Consult a qualified electrician if in doubt of connecting the machine to the power source.
Unplug the power cord when the machine is not in use. The foot control must be used with the appliance by FC- 1902A (110-120V area)/ FC-2902A (220-240V area)/ 4C- 316Q (110-125V area).
Sewing light
Press the main switch (A) to “|” for power and light.
IMPORTANT NOTICE
For appliances with a polarized plug (one blade is wider than the ted lo in a polarized way this does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install the proper outlet. Do not modify the plug in any way.

• Polarized attachment plug
• The conductor intended to be grounded

Two-Step Presser Foot Lifter

When sewing several layers of thick fabrics, the presser foot can be raised to a higher position for easy positioning of the work. (A)
The presser foot will remain raised as long as you hold up the presser foot lifter. As soon as you release it, the presser foot will drop back down to the intermediate position.

Adjusting Presser Foot Pressure
The presser foot pressure of the machine has been pre-set and requires no particular readjustment according to the type of fabric (light or heavy weight).
However, if you need to adjust the presser foot pressure, turn the presser adjusting screw with a coin.
For sewing, very thin fabric, loosen the pressure by turning the screw counterclockwise, and for heavy fabric, tighten by turning it clockwise.
It is suggested that you turn the screw in one-quarter-inch increments so that it can be easily reset to factory settings.

Accessories

Standard accessories (1)

• a. All-purpose foot

• b. Zipper foot

• c. Buttonhole foot

• d. Button sewing foot

• e. Seam ripper/ brush

• f. Edge/ quilting guide

• g. Pack of needles

• h. Spool holders (2x)

• i. Bobbin (3x)

• j. L-screwdriver

• k. Auxiliary Spool Pin

• l. Spool pin felt

• m. Softcover
  Optional accessories (2)
  These 10 accessories are not supplied with this machine; they are, however, available for purchase from your authorized retailer.)

• n. Satin stitch foot

• o. Overcasting foot

• p. Hemmer foot

• q. Cording foot

• r. Blind hem foot

• s. Quilting/ straight stitch foot

• t. Gathering foot

• u. Darning/ embroidery foot

• v. Even Feed foot

• w. Twin needle

Winding the Bobbin

• Place thread and corresponding spool holder onto to spool pin. (1/2)
• Snap thread into thread guide. (3)
• Wind thread clockwise around bobbin winder tension discs. (4)
• Thread bobbin as illustrated and place on spindle. (5)
• Push the bobbin spindle to the right. (6)
• Hold thread end securely. (7)
• Step on the foot control pedal. (8)
• Trim thread close to the bobbin & then continue windinguntil the bobbin is full. (9)
• Cut thread, push bobbin spindle to left (10), and remove.

Please Note:
When the bobbin winder spindle is in the “bobbin winding” position, the machine will not sew, and the handwheel turn.
To start sewing, push the bobbin winder spindle to the left (sewing position).

Inserting the Bobbin

When inserting or removing the bobbin, raise the presser foot & make sure the needle is fully raised.

1. Remove the bobbin cover plate by pushing the small tab to the right of the cover towards the right.
2. Insert the bobbin in the bobbin case with the thread running counterclockwise direction (arrow).
3. Pull the thread through the slit (A).
4. Draw the thread clockwise until it slips into the notch (B), while holding the bobbin down with the tip of your finger.
5. Pull out about 15 cm (6 inches) of thread towards the back of the plate and attach the bobbin cover plate. (C)
   Attention:
   Turn the power switch to off (“O”) before inserting or removing the bobbin.

Threading the Upper Thread

This is a simple operation but it is important to carry out correctly as by not doing so.

• Start by raising the needle to its highest point (1), and continue turning the handwheel* counterclockwise until the needle just slightly begins to descend. You must raise the presser foot to release the tension discs.
  Note:
  For safety, it is strongly suggested you turn off the power before threading.

• Lift up the spool pin. Place the spool of thread on the holder with the thread coming off the spool from the back as shown and place appropriate spool holder next to the spool. For small thread spools, place small side of spool holder next to spool. (2)

• Draw thread from spool through the upper thread guide (3) and pulling thread through the pre-tension spring as illustrated. (4)

• Thread tension module by leading thread down right channel. (5) During this process it is helpful to hold the thread between the spool and thread guide, as this will help to seat the thread between the tension discs.

• At the top of this movement pass thread from right to left through the slotted eye of the take-up lever and then downwards again. (6)

• ow pass the thread behind the horizontal thread guide, and then behind the thin wire needle clamp guide (7) and then down to the needle which should be threaded from front to back.

• Pull about 6 – 8 inches of thread under the presser foot to the rear beyond the needle eye. Trim thread to length with built-in thread cutter. (8)

• Never turn the handwheel away from you as this may cause the timing to be disrupted. Always turn the handwheel counterclockwise (towards you).

Automatic Needle Threader

• Thread upper tension of machine up to the thin wire in front of the needle clamp.
• Raise the needle to its highest position.
• Set the Pattern Selector Dial (see item # 13 on page 2 of the manual) to Straight Stitch.
• Set Stitch Width Dial (see item # 11 on page 2 of the manual) to “0”.
• Set Three Needle Position Dial (see item # 9 on page 2 of the manual) to center position.
• Lower the needle threader (A) as far down as it will go, then push it back gently so that the hook inside the threader will slip into the eye of the needle.
• The threader automatically swings to the threading position (B).
• Pass the thread under thread guide (C), from left to right.
• Pass the thread in front of the needle around the hook (D) from bottom to top.
• Release lever (A), by swinging it away from you & then pushing it back up to the resting position.
• Pull the thread through the needle eye.

Attention:
Turn the power switch to off (“O”)!
The needle threader is designed to work best with a size 14 needle. Your machine is equipped with a standard size 14 needle at the factory.

Raising the Bobbin Thread

Hold the upper thread with the left hand. Turn the handwheel (1) towards you (counterclockwise) lowering, then raising the needle.

Note:

• If it is difficult to raise the bobbin thread, check to make sure the thread is not trapped by the hinged cover or the Removable Extension Table.
• Gently pull on the upper thread to bring the bobbin thread up through the needle plate hole. (2)
• Lay both threads to the back under the presser foot. (3)

Thread Toncinn

Upper thread tension
Basic thread tension setting: “4”. (1)
To increase the tension, turn the dial to the next number up.
To reduce the tension, turn the dial to the next number down.

• A. Normal thread tension for straight stitch sewing.
• B. Thread tension too loose for straight stitch sewing. Turn dial to higher number.
• C. Thread tension too tight for straight stitch sewing. Turn dial to lower number.
• D. Normal thread tension for zig zag and decorative sewing.
• Correct thread tension is when a small amount of the upper thread appears on the bottom side of fabric. If the thread is looping or birdnesting on the underside of the fabric, this is an indication that the upper machine tension is not threaded correctly.

Lower thread tension
The bobbin tension has been set correctly at the factory, so you do not need to adjust it.

Please note:

• Proper tension setting is important for strong seams.
• There is no single tension setting appropriate for all stitch functions, thread or fabric.
• A balanced tension (identical stitches both top and bottom) is usually only desirable for straight stitch construction sewing.
• 90% of all sewing will be between “3” and “5”.
• For zig zag and decorative sewing stitch functions, thread tension should generally be less than for straight stitch sewing.
• For all decorative sewing you will always obtain a nicer stitch and less fabric puckering when the upper thread appears on the bottom side of your fabric.
• If the thread is looping or birdnesting on the top of the fabric, this is an indication that the bobbin thread has not been threaded correctly.

How to Choose Your Pattern

The diagram on this page displays the stitch patterns available on the machine.
Stitches in the top of the diagram are indicated on the pattern selector dial in gray. To select the patterns indicated with the gray color, turn the pattern selector dial. (e)

For top row stitches B, C, D, E, I, J, and K follow these steps:

• Set the Three Needle Position Dial (b) to the Center.

• Set the Stitch Width Dial (c) to 6. This will give you the widest stitch. If you would like a narrower stitch, set the Stitch Width Dial to between 1 and 5.

• Set the Stitch Length Dial (d) to 2. You can adjust the density by moving the Stitch Length Dial to 1 to make the stitching closer, or towards 4 to make it longer.
  For top row stitches F, G, and H follow these steps:

• Set the Three Needle Position Dial (b) to the Center.

• Set the Stitch Width Dial (c) to 6. This will give you the widest stitch. If you would like a narrower stitch, set the Stitch Width Dial to between 1 and 5.

• Set the Stitch Length Dial (d) to 1. You can adjust the density by moving the Stitch Length Dial to 0.5 to make the stitching closer.
  Further instructions for setting the stitch width & the stitch length dials can be found on page 28.
  To obtain the other patterns, turn the stitch length dial to “S1” or “S2”, select the pattern desired with pattern selector dial, and adjust the stitch width with the stitch width dial.

The pattern selector dial may be turned in either direction.

• a. Reverse sewing lever
• b. Three needle position dial
• c. Stitch width dial
• d. Stitch length dial
• e. Pattern selector dial

Three Needle Position Dial

The needle position can be altered with the “Three needle position dial”. For normal work, the needle position in the middle. For edge stitching or sewing parallel lines of topstitching, select needle position left or right. For twin needle stitching, needle position is middle.
In order to set the Three Needle Position Dial (See item # 9 on page 2 of the manual) to the left, in the center or to the right, the Stitch Width Dial must be set to “0” position.

• a. Straight
• b. Zig-zag
• L. Left Needle Position
• M. Middle Needle Position
• R. Right Needle Position

Stitch Width Dial & Stitch Length Dial

The function of stitch width dial
When doing a zig zag or a decorative pattern you can alter the width from 1mm to 6mm. To obtain a very narrow stitch, set the dial to 1, to obtain the maxinum 6mm width, set the dial to 6. When the dial is set to 0, you will obtain a straight stitch. (1)
The stitch width dial (see item # 11 on page 2 of your manual) is also the control for the straight stitch infinite needle position. To use this function your Pattern Selector Dial (see item # 13 on page 2 in the manual) must be set at Straight Stitch. For an infinite needle position, first set the Three Needle Position Dial so that the needle is positioned to the right and then by moving the stitch width dial between “0” and “6”, you can position the needle where you require it.

Function of stitch length dial while zig-zag stitching
Set the pattern selector dial to zig zag or any other decorative pattern.
The density of zig zag or decorative stitches increases as the setting of the stitch length dial approaches “0”. The smaller the number the closer, or denser the stitches will be.
Standard zigzag stitches are usually achieved at “3” or below. (2) Dense zig- zag stitches are called satin stitches. (2)

Function of stitch length dial for when straight stitching
For straight stitch sewing, turn the Pattern Selector Dial to the straight stitch setting. Turn the Stitch Length Dial, and the length of the individual stitches will decrease as the dial approached “0”. The length of the individual stitches will increase as the dial approaches “4”. Generally speaking, use a longer stitch length when sewing heavier weight fabrics or when using a thicker needle or thread. Use a shorter stitch length when sewing lighter weight fabrics or when using a finer needle or thread.

• The standard setting for sewing a seam is between 2 and 3.
• For basting purposes, set the stitch length all the way to 4 (longest).

Sewing Straight Stitch

To begin sewing, set the machine for a straight stitch. (1)
Set the stitch length to between 2 and 3.
Place the fabric under the presser foot with the fabric edge lined up with the desired seam guide line on the needle plate. (2)
Lower the presser foot lifter, and then step on the foot controller to start sewing. (3)

• Reverse Sewing
  To secure the beginning and the end of a seam, press down the reverse sewing lever (A). Sew a few reverse stitches.
  Release the lever and the machine will sew forward again. (1)

• Removing the Work
  Turn the handwheel toward you (counterclockwise) to bring the thread take up lever to its highest position, raise the presser foot and remove work behind the needle and presser foot. (2)

• Cutting the Thread
  Pull the threads under and behind the presser foot. Guide the threads to the side of the face plate and into thread cutter (B). Pull threads down to cut. (3)

Choosing Stretch Stitch Patterns

The stretch stitch patterns are indicated with blue and red colors on the pattern selector dial. To select these stitches, turn the pattern selector dial to the desired pattern. Then, turn the stitch length dial to the indicator marked “S1” or “S2”.
Though there are severall stretch patterns, here are two examples:

Straight Stretch Stitch (1)
Set the pattern selector dial to .
Set the stitch width dial to “1”.
Used to add triple reinforcement to stretch and hardwearing seams.
The machine sews two stitches forward and one stitch backwards.

Ric Rac (2)
Set the pattern selector dial to ” ”
Set the stitch length dial to “S1” or “S2”.
Adjust the stitch width dial to between “3” and “6”.
Ric rac stitch is suitable for firm fabrics like denim, corduroy, poplin, duck, etc.

Blind Hem

For hems on curtains, trousers, skirts, etc.
Blind hem for stretch fabrics.

Blind hem for firm fabrics. Set the stitch length dial with the range shown on the diagram at the right. Blind hems, however, are normally sewn with a longer stitch length setting. Set the stitch width dial at a setting appropriate for the weight/type of fabric being sewn, within the range shown in the diagram on the right of the pares, and al Wider stron is sitch is header weight fabrich.
Sew a test first to make sure the machine settings are appropriate for the fabric.
Blind Hem:
Turn up the hem to the desired width and press. Fold back (as shown in Fig. 1) against the right side of the fabric with the top edge of the hem extending about 7 mm (1/4″) to the right side of the folded fabric.
Start to sew slowly along the fold, so that the needle drops through the edge of the fold. (2)
Unfold the fabric when hemming is completed and press.
Note:
To make blind hem sewing even easier, use a blind hem foot, available from your SINGER® retailer. (See page 10 for part number)

Sew 1-step Buttonholes

Buttonhole sewing is a simple process that provides reliable results. It is strongly suggested to always make a test buttonhole on a sample of your fabric before working on your garment. Stabilizer should alsways be used when making buttonholes.

Making a Buttonhole
Making a Buttonhole on Stretch Fabrics (E)

1. Using tailor’s chalk, mark the position of the buttonhole on the fabric.
2. Attach the buttonhole foot and set the Pattern Selector Dial to ” “. Set stitch length dial to ” “. Set the stitch width at “6”. The width however may need to be adjusted according to the project. Sew a test first to determine this.
3. Lower the presser foot aligning the marks on foot with the marks on the fabric (A). (The front bar tack will be sewn first.) (Align the mark on the fabric (a) with the mark on the foot (b).)
4. Open the button plate and insert the button (B).
5. Lower the buttonhole lever and gently push it back (C).
6. While lightly holding the upper thread, start the machine.
7. Buttonhole stitching is done in the order (D).
8. Stop the machine when the buttonhole cycle has completed.

Making a Buttonhole on Stretch Fabrics (E)
When sewing buttonholes on stretch fabric, hook-heavy thread or cord under the buttonhole foot. When the buttonhole is sewn the legs will overcast the cord.

1. Mark the position of the buttonhole on the fabric with the tailor’s chalk, attach the buttonhole foot, and set the pattern selector dial to ” “. Set stitch length dial to ” “.

2. Hook the heavy thread onto the back end of the buttonhole foot, then bring the two heavy thread ends under & to the front of the foot, insert them into the grooves, and temporarily tie them there.

3. Lower the presser foot and start sewing.
   Set the stitch width to match the diameter of the gimp thread.

4. Once sewing is completed, gently pull the heavy thread to remove any slack, then trim off the excess.

Left and Right Side Balance for Buttonhole

Stitch density on right and left sides of buttonhole can be adjusted by buttonhole balance control dial.
This dial should usually be in a neutral position (between “+” and ” “)
If the stitches on the left side of buttonhole are too close vtogether, turn the dial to the left (+).

• Turning dial to the left opens left side.
  If the stitches on the left side of the buttonhole are too open, turn the dial to the right (-).

• Turning dial to right closes left side.

Sewing on Buttons

Move the drop feed control to right side to lower the feed dogs. (1)
Change the all purpose foot to the button sewing foot. (2)
Set the stitch length to “0”.
Place the button and fabric under the Button Sewing foot, as illustrated in (3).
Set the machine for zig-zag stitch, then set the width to number “3” – “6”. Turn the handwheel to check that the needle goes cleanly into the left and right holes of the button. Adjust the stitch width, as needed, according to the distance between the holes of the button. Slowly sew on the button with about 10 stitches.
Raise the needle out of the fabric. Set the machine for straight stitch again, then sew a few securing stitches to finish.
If a shank is required, place a darning needle on top of the button and sew. For buttons with 4 holes, sew through the front two holes first, push the work forward and then sew through the back two holes.

Installing the Removable Extension Table

• Hold the removable extension table horizontally, and push it in the direction of the arrow. (1)
• To remove the extension table, pull it toward the left.
• The inside of the removable extension table can be utilized as an accessory box.
• To open, flip cover down as shown. (2)

Attaching the Presser Foot Shank

Raise the presser bar (a) with the presser foot lifter. Loosen or remove the presser shank screw. Line up the opening in the shank with the opening on the presser bar and then tighten the screw. (1)

• Attaching the presser foot
  Lower the presser foot shank (b) using the presser foot lifter, until the cut- out (c) is directly above the pin (d). (2) The presser foot (f) will engage automatically.

• Removing the presser foot
  Raise the presser foot using the presser foot lifter. (3) Raise the lever (e) and the foot disengages.

• Attaching the edge/ quilting guide
  Attach the edge/ quilting guide (g) in the slot as illustrated. Adjust as needed for hems, pleats, quilting, etc. (4)

• Attention :
  Turn the power switch to off (“O”) when carrying out any of the above operations!

Needle/ Fabric/ Thread Chart

NEEDLE, FABRIC, THREAD SELECTION GUIDE

9-11 (70-80)

| Lightweight fabrics-thin cottons, voile, silk, muslin, interlocks, cotton knits, tricots, jerseys, crepes, woven polyester, shirt & blouse fabrics.| Thread in cotton, polyester or cotton wrapped polyester.
11-14 (80-90)| Medium weight fabrics-cotton, satin, kettlecloth, sailcloth, double knits, lightweight woolens.| Most threads sold are all purpose and are suitable for these fabrics and needle sizes.

Always use the same thread in the upper tension and in the bobbin.

14 (90)| Medium weight fabrics-cotton duck, woolen, heavier knits, terrycloth, denims.
16 (100)| Heavyweight fabrics-canvas, woolens, outdoor tent and quilted fabrics, denims, upholstery material (light to medium).
18 (110)| Heavy woolen, overcoat fabrics, upholstery fabrics, some leathers and vinyls.| Heavy duty thread in the upper tension, all purpose thread in the bobbin. Set stitch length to 3 or 4.

IMPORTANT: Match needle size to thread size and weight of fabric.

NEEDLE, FABRIC SELECTION

double knits.
SINGER® 2045| Semi-ball point needle, scarfed. 9 (70) to 18 (110).| Natural and synthetic woven fabrics, polyester blends. Knits-polyesters, interlocks, tricot, single and double knits.

Also sweater knits, Lycra®, swimsuit fabric, elastic.

SINGER® 2032| Leather needles. 12 (80) to 18 (110).| Leather, vinyl, upholstery. (Leaves smaller hole than standard large needle.)

Note:

1. For best sewing results always use genuine SINGER needles.
2. Replace needle often (approximately every other garment ) and/ or at first thread breakage or skipped stitches.

How To Drop Feed Dog

For ordinary sewing, keep the feed dogs engaged, for freehand embroidery, sewing on buttons and darning, drop the feed dogs.
To raise (a) and lower (b) feed dogs. (2)

• To lower feed dogs: Push lever towards position (b). (2)
• To raise feed dogs: Push lever towards position (a). (2). Turn handwheel towards you until you see the feed dogs re-engage.

Inserting & Changing Needles

Change the needle regularly, especially if it is showing signs of wear and causing problems. For best sewing results always use SINGER needles.

Insert the needle as illustrated as follows:

• A. Loosen the needle clamp screw and tighten again after inserting the new needle. (1)
• B. The flat side of the shaft should be towards the back.
• C/D.Insert the needle as far up as it will go.

Troubleshooting Guide

the machine.
| 2. The thread tension is too tight.| 2. Reduce the thread tension. (lower number)
| 3. The thread is too thick for the needle.| 3. Select a larger needle.
| 4. The needle is not inserted correctly.| 4. Remove and reinsert the needle. (flat side towards the back)
| 5. The thread is wound around the spool holder pin.| 5. Remove the reel and wind thread onto reel.
| 6. The needle is damaged.| 6. Replace the needle.
Lower thread breaks| 1. The bobbin case is not inserted correctly.| 1. Remove and reinsert the bobbin case and pull on the thread.
| 2. The bobbin case is threaded wrong.| 2. Check both spool and bobbin case.
Skipped stitches| 1. The needle is not inserted correctly.| 1. Remove and reinsert needle. (flat side towards the back)
| 2. The needle is damaged.| 2. Insert a new needle.
| 3. The wrong size needle has been used.| 3. Choose a needle to suit the thread and fabric.
| 4. The foot is not attached correctly.| 4. Check and attach correctly.
Needle breaks| 2. The needle is not correctly inserted.| 2. Insert the needle correctly. (flat side towards the back)
| 3. Wrong needle size for the fabric.| 3. Choose a needle to suit the thread and fabric.
| 4. The wrong foot is attached.| 4. Select the correct foot.
Loose stitches| 1. The machine is not correctly threaded.| 1. Check the threading.
| 2. The bobbin case is not correctly threaded.| 2. Thread the bobbin case as illustrated.
| 3. Needle/fabric/thread combination is wrong.| 3. The needle size must suit the fabric and thread.
| 4. Thread tension wrong.| 4. Correct the thread tension.
Seams gather or pucker| 1. The needle is too thick for the fabric.| 1. Select a finer needle.
| 2. The stitch length is adjusted wrong.| 2. Readjust the stitch length.
| 3. The thread tension is too tight.| 3. Loosen the thread tension.
Uneven stitches, uneven feed| 1. Select a better quality thread.| 1. Select a better quality thread.
| 2. The bobbin case is threaded wrong.| 2. Remove bobbin case, thread and insert correctly.
| 3. Fabric has been pulled.| 3. Do not pull on the fabric while sewing, let the feed dogs pull the fabric under the foot.
The machine is noisy| 1. Lint or oil have collected on the hook or needle bar.| 1. Clean the hook and feed dog as described.
| 2. The needle is damaged.| 2. Replace the needle.
The machine jams| Thread is caught in the hook because the upper tension is not threaded correctly.| Remove the upper thread and bobbin case. Gently rock the handwheel backwards and forwards by hand and remove the thread from the bobbin area.

Correct Disposal of this product

This marking indicates that this product should not be disposed of with other household wastes throughout the European Union. To prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material resources. To return your used device, please use the return and collection systems or contact the retailer where the product was purchased. They can take this product for environmental safe recycling.

CE – Authorised Representative
VSM Group AB, SVP Worldwide
Drottninggatan 2, SE-56184, Huskvarna, SWEDEN

FAQs

What is the maximum sewing speed of the SINGER 4432 Heavy Duty Sewing Machine?

The SINGER 4432 Heavy Duty Sewing Machine has a maximum sewing speed of 1,100 stitches per minute.

How many built-in stitches are available on the SINGER 4432 Heavy Duty Sewing Machine?

The SINGER 4432 Heavy Duty Sewing Machine features 32 built-in stitches, including basic, decorative, and buttonhole stitches.

What type of motor does the SINGER 4432 Heavy Duty Sewing Machine have?

The SINGER 4432 Heavy Duty Sewing Machine is equipped with a powerful motor that provides 60% more power than standard sewing machines.

What type of needle does the SINGER 4432 Heavy Duty Sewing Machine use?

The SINGER 4432 Heavy Duty Sewing Machine uses standard sewing machine needles.

What is the weight of the SINGER 4432 Heavy Duty Sewing Machine?

The SINGER 4432 Heavy Duty Sewing Machine weighs approximately 17.42 pounds.

What materials are included with the purchase of the SINGER 4432 Heavy Duty Sewing Machine?

The SINGER 4432 Heavy Duty Sewing Machine comes with various accessories, including bobbins, needles, spool caps, a screwdriver, a seam ripper, a lint brush, and an auxiliary spool pin.

What is the stitch width of the SINGER 4432 Heavy Duty Sewing Machine?

The SINGER 4432 Heavy Duty Sewing Machine offers a maximum stitch width of 6mm.

How many needle positions does the SINGER 4432 Heavy Duty Sewing Machine have?

The SINGER 4432 Heavy Duty Sewing Machine has three needle positions: left, center, and right.

What type of bobbin system does the SINGER 4432 Heavy Duty Sewing Machine use?

The SINGER 4432 Heavy Duty Sewing Machine uses a top drop-in bobbin system with a clear cover for easy monitoring of thread supply.

What type of lighting does the SINGER 4432 Heavy Duty Sewing Machine have?

The SINGER 4432 Heavy Duty Sewing Machine is equipped with a built-in LED light to illuminate the sewing area.

How do you adjust the stitch length on the SINGER 4432 Heavy Duty Sewing Machine?

The SINGER 4432 Heavy Duty Sewing Machine has a stitch length dial that allows users to adjust the stitch length up to 4mm.

What is the voltage requirement for the SINGER 4432 Heavy Duty Sewing Machine?

The SINGER 4432 Heavy Duty Sewing Machine operates on 110 volts, making it suitable for use in North America.

How do you change the needle on the SINGER 4432 Heavy Duty Sewing Machine?

To change the needle on the SINGER 4432 Heavy Duty Sewing Machine, simply loosen the needle clamp screw, remove the old needle, insert a new needle with the flat side facing the back, and tighten the screw.

Video-SINGER 4432 Heavy Duty Sewing Machine

Download this Manual:SINGER 4432 Heavy-Duty Sewing Machine Instruction Manual

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>