MATCO TOOLS MTCBTBEANORG Orange Logo Beanie User Manual
- July 4, 2024
- MATCO TOOLS
Table of Contents
MATCO TOOLS MTCBTBEANORG Orange Logo Beanie
Product Specifications
- Built-in Microphone
- Compatible with most Smart Phones
- Rechargeable Li-polymer Battery
- Wireless Technology
Product Usage Instructions
- On/Off Power; Play/Pause; Answering/Dialing
- Volume Up/Next Track
- Volume Down/Previous Track
- Charging Light
Washing Instructions
Remove the electronics before washing.
- Turn the beanie inside-out and locate the control module (A) held in the pocket between the double-layer inside the beanie.
- Gently push the control module towards the opening in the rear of the beanie and carefully remove it.
- Repeat the above steps for the additional speaker (B) located at the opposite side of beanie.
FAQ
-
Q: Can I wash the beanie with the electronics in
A: No, you must remove the electronics before washing to avoid damaging them. -
Q: How do I charge the beanie?
A: Use a compatible charging cable to connect to a power source. The charging light will indicate when it’s charging. -
Q: Is it safe to use this product around small children?
A: Please handle with care and keep out of reach of small children due to the internal rechargeable Lithium-Ion battery.
WIRELESS
TECHNOLOGY
BEANIE
USER MANUAL
Matco Tools
Stow, Ohio 44224 www.matcotools.com 2405255-67
CAUTION! WARNING/SAFETY
This product contains a non-changeable internal rechargeable Lithium-Ion
battery.
Please handle with care.
- DO NOT expose the beanie to liquids or moisture.
- DO NOT use the beanie in the rain.
- DO NOT attempt to tamper with the Wireless Technology module by piercing, disassembling, opening or removing the battery, etc.
- DO NOT put, store, or leave your beanie in or near sources of heat, fire, in a pressurized container, or in a microwave oven.
- DO NOT leave your beanie in an unventilated vehicle under direct sunlight.
- DO NOT store the beanie near acidic or alkaline material.
- DO NOT expose the beanie to temperatures over 140˚ F (60˚ C)
- ALWAYS remove the Wireless Technology module and speakers before washing.
- ALWAYS keep the electronics and batter out of the reach of infants and small children.
DISPOSAL OF THE PRODUCT
Information on Waste Disposal for Consumers of Electrical and Electronic
Equipment.
This mark on a product and/or accompanying documents indicates when it is to
be disposed of; it must be treated as Waste Electrical & Electronic Equipment
(WEEE). Any WEEE marked waste products must not be mixed with general
household waste, but separated for the treatment, recover and recycling.
Please take all WEEE marked waste to your Local Authority Civic waste site,
where it will be accepted free of charge. If all consumers dispose of Waste
Electrical & Electronic Equipment correctly, they will be helping to save
valuable resources and preventing any potential negative effects upon human
health and the environment of any hazardous materials that the waste may
contain.
HOW TO USE
- Pairing: Press the ON/OFF button for about 5 seconds until the LED light slow flashes from blue to red.
- Open the Wireless Technology in your phone and pair with your beanie.
- All beanies pair with “MATCO”.
- After pairing successfully, open the music in your phone and enjoy.
- Press the “Play” button to pause/play the music.
- Answer a phone call by pressing ON/OFF button.
- Long press the “+” button for volume up.
- Long press the “_” button for volume down.
- Double-click “Play” button to access Siri/Alexa. Repeat to turn off Siri/Alexa.
- Device can be charged using a Type-C charging cable- when charging, the LED light will turn red; when the LED light is off, it means the headset is fully charged.
- Hand wash only. Use cold water and air-dry.
- On/Off Power; Play/Pause; Answering/Dialing
- Volume Up/Next Track
- Volume Down/Previous Track
- Charging Light
WASHING INSTRUCTIONS
Remove the electronics before washing.
STEP 1. Turn the beanie inside-out and locate the control module (A)
held in the pocket between the double-layer inside the beanie. 
STEP 2. Gently push the control module towards the opening in
the rear of the beanie and carefully remove it. 
STEP 3. Repeat the
above steps for the additional speaker (B) located at the opposite side of
beanie. 
FCC RADIATION EXPOSURE STATEMENT
This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. USA: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation of the device.
Canada: Operation is subject to the following conditions:
- This device may not cause interference and
- This device must accept any interference, including interference that may cause undesired operation of the device.
Note: This equipment has been tested and found to comply with limits for
a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful
interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if
not installed and used in accordance with instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one of more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or and experienced radio/TV technician for help.