Eachine TYRO79 Racing RC Drone User Manual

Eachine TYRO79 Racing RC Drone User Manual

Package included

• 1 x 140mm racing frame kit
• 2 x 1607 2800KV brushless motor CW
• 2 x 1607 2800KV brushless motor CCW
• 1 x 4 IN 1 20A BLHeli_S ESC
• 1 x Customized F4 flight controller
• 1 x 700TVL CMOS camera
• 1 x 5.8G 40CH 0mw/25mw/200mw switchable VTX
• 2 x 3030 4-blade propeller CW
• 2 x 3030 4-blade propeller CCW

Frame kit

• Wheelbase: 140mm
• Bottom plate thickness: 3mm
• Side plate thickness: 1mm
• Frame kit material: 3K
• carbon fibre & 6065 aluminium

Motor

• KV: 2800KV
• Lipo cell: 2-4S
• Weight: 17.8g (includes wires)
• Output shaft length: 14mm
• Maximum pull: signal 630g
• (4S 3030 4-blade propeller)
• Maximum power: 350W
• Configuration: 9N/12P
• Mounting hole distance: 12*12mm
• Mounting holes: φM2
• Bearing: NSK
• N52 Strong NdFeB Magnet
• Recommend propeller: 3 inch

ESC

• Continuous current: 20A
• Peak current: 25A (10S)
• BEC output: no
• Input voltage: 2-4S
• Main control chip: 48mhz EFM8BB2
• Firmware upgrade: Supports Dshot600/BLHeli_S/Oneshot125
• MOS: 3*3
• MOS type: vs3610ae 30v64a

Flight controller

• Main control chip: STM32F411
• Sensor: ICM20602 6-axis
• Integrated OSD
• PPM/DSM/IBUS/UAR share: UART1-RX
• Mounting hole distance: 20*20mm
• Weight: 24g
• PID circulation rate and refresh rate can be up to 32kHz
• Supports Betaflight/clean flight/in firmware

Switchable VTX

• Supports TBS SmartAudio
• Transmitting power: 0mW/25mW/100mW/200mW switchable
• Channel: 40CH
• Full video format: NTSC/PAL
• Input voltage: 7V~24V
• Power dissipation: + 12V/600MW
• Size: 25×20×6mm
• Weight: ≤3.2g (except antenna)
• There are two ways to control the frequency and power of the launches:
• Enter the release: FEATURES->VTX SA can enter the following interface.
• <1> uses remote control to visualize control, as shown in Figure 1.1

The second row is the status bar, respectively.

• F: freestyle modeF5: is now in frequency band F, fifth frequency point.
• 5820: now has a frequency of 5820.
• 500: now has a transmit power of 500MW

Third lines

• BAND: indicates frequency band, and BAND can be modified by remote control.
• A (BOSCAM A) B (BOSCAM B)
• E (BOSCAM E) F (FATSHARK) F (E)

Fourth lines

• CHAN: represents frequency points, and the 1—8 can be modified by remote control.

Fifth lines

• (FREQ): indicate the corresponding frequency now, changing with the band and Chan above.

Sixth lines

• POWER: indicates the transmission power and can be adjusted.

Switchable VTX

Seventh lines
SET: Enter and select YES to confirm your BADN, CHAN, and POWER settings and take effect immediately., as shown in Figure 1.2 below.

Eighth lines

• The CONFIG: function is set in, as shown in Figure 1.3 below.
• OP MODEL: mode adjustment, with free mode and race mode, needs a reboot to take effect.
• FSEL MODE: regulates frequency setting mode, CHAN and user, user mode is temporarily invalid.
• PIT FMODE:PITMODE mode, with PIR and POR mode.

Switchable VTX
In the POR mode, POR FREQ: can enter into any frequency between 5300 and 5900, as shown in Figure 1.4.

STATX : status information
XMM-VTX is operated by a button with three LED lights (red light CH1-8; blue light BAND1-5; green light power 1-3 <25- 100-200 mW>)and TBS Smart Audio remote control operation. Keyboard operation: Long press 3S (three LED indicators are all on) to open and enter CH switching operation, and the red light will flash, flashing once representing the current (2-8 times for CH2-CH8 respectively).

At this time, a short press of the key CH plus 1 will flash the corresponding number of times. CH1-8 cycle. Press the button 3S (three LED lights are all on) to open and enter the BANDswitching operation, and the blue light will flash. The flash once represents the current BAND1 (2-5 times for BAND2-BAND5 respectively).

At this time, press the button BAND plus 1, and the blue light will flash correspondingly. BAND1-5 cycle. Press the button 3S (three LED lights are all on) again to open the power switching operation, and the green light will flash, one time representing the current power of the first grade (2-3 times for the green light flashing respectively), at this time, press the button power to add one gear, and the green light will flash the corresponding number of times.

Power stall 1-3 cycles
Press the button 3S again (3 LED lights are all bright) to release the above settings again. Note that the previous settings will not be saved if the power is off before saving. For example, if CH is only set, it is also necessary to press 3S three times longer to save the settings. Long press button 8S (green light) to quit PIT mode.

Switchable VTX
Note: In the remote control, the power of 25 corresponds to the actual 25 mW, 200 corresponds to the actual 100 mW, and 500/800 corresponds to the actual 200 mW.

• 5.0 Switchable VTX
• 6.0 Camera
• Case size: 19mm*19mm
• Weight: 9.5g
• Total pixels: PAL: 1020H×596V (0.61MP);
• NTSC: 1020H×508V (0.52MP)
• Effective pixels: PAL: 976H×582V (0.57MP);
• NTSC: 976H×494V (0.48MP)
• Signal system: PAL/NTSC switchable
• Resolution ratio(horizontal center): 700TVL
• Video output: 1.0Vp-p/75Ω
• Automatic gain control: 0.25/0.50/0.75/1.00, up to 55dB
• White balance: off
• Exposure mode: electron exposure
• Electronic shutter: 1/50(1/60) – 1/100000 S
• Gamma correction: 0.45/1.0
• Synchronization method: inter-sync
• Camera lens: standard 2.1mm
• Lens operating voltage: DC 5-12V
• Working current: 70mA (low power consumption)
• Working temperature: -20℃~-60℃
• Humidity: 0%~98%

Screws

Adjusting parameter

1. Click connect connection
2. Click the RX interface under UART2 under the ports option, as shown in the figure.
3. Click CONFIGURATION to change to dshot600.
4. 8.0 Adjusting parameter
5. Click CONFIGURATION; change to SBUs.
6. Click modes, add arm and angle, drag the slider between 1300 and 1700, and set the arm to AUX1 and angle to aux2.
7. Push the slider to test the positive and negative rotation of the motor, such as the error.
8. Click font manager, select a beta flight, and click upload font.
9. Click setup, and calibrate the accelerometer.

Motor Unlock/lock

Motor Unlock
Put the throttle rocker at the lowest point, move the rudder rocker to the right and keep it for more than 2 seconds. The blue state the indicator is always on, that is unlocks the motor.

Motor lock
Put the throttle rocker at the lowest point, and move the rudder rocker to the leftmost side, and the red state indicator is always turned on to lock the motor. At this time, pushing the throttle rocker motor upward will not rotate.

Traversing flight

1. Flying is more suitable for experienced pilots.
2. During the flight, please keep the flight within the video receiving range (the actual range depends on the flight environment and weather conditions).
3. During the flight, please avoid crowds, animals and High voltage wires and other obstacles.

Download PDF:Eachine TYRO79 Racing RC Drone User Manual

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>