MOTOROLA SOLUTIONS PDR8000 Portable Digital Repeater User Guide

safer starts here

PDR8000®

Ordering Guide

Revision 4.4

May 2024

Important Notes

1. Custom Filtering: Only the frequency plans shown in this ordering guide are available as standard configurations. For custom filtering, please contact a Sales Solution Specialist for assistance.
2. Frequencies Required: PDR8000® frequencies must be specified when placing an order. If a duplexer is ordered, it is custom tuned and cannot be re-tuned in the field.
3. Delivery Time: Standard PDR8000® delivery time is 22-24 weeks after receipt of a purchase order and a valid frequency plan. Frequency information must be accurate and in accordance with the frequency plan requirements described in this document in order to avoid delays.
4. Duplexer: Duplexer is not mandatory and the ‘No Duplexer’ option can be chosen when full duplex capability is not desired.
5. Power Cables: PDR8000® suitcase models include standard AC & DC Power Cables. Customer must provide their own 12VDC power supply for PDR8000® rackmount which is designed to fit into a standard 19″ rack.

How to Interpret a Frequency Plan Diagram

Below is an example of a frequency plan with the set of rules that must be met for it to be a valid selection.

Frequency Plan Examples

• Ensure the PDR8000 frequencies are within the Valid frequency range (MHz)
  • PDR Tx/Rx 136-174
• Ensure the Separation (MHz) frequency requirements are met
  • at least 4.5MHz and no more than 5.5MHz between the highest Tx and the lowest Rx frequencies when Tx is lower than Rx   OR
  • at least 4.5MHz and no more than 5.5MHz between the highest Rx and lowest Tx frequencies if Rx is lower than Tx)
• The provided Tx and Rx frequencies are used as the center frequency. Ensure that any additional Tx/Rx frequencies do not exceed the Maximum bandpass (MHz)
  • difference between the lowest and highest programmed Tx frequencies must be less than or equal to 0.3MHz
  • difference between the lowest and highest programmed Rx frequencies must be less than or equal to 0.3MHz
• Each frequency plan identifies the repeater mount type that is it compatible with
  • Suitcase ( SC )- check mark indicates supported
  • Rackmount ( VM )- check mark indicates supported

• For 700MHz and 800MHz, there is a Frequency pair spacing requirement instead of separation
  • each Tx-Rx frequency pair must be exactly 30MHz apart

Preparing a Quote Without Customer Frequencies

If preparing a quote before customer frequencies are known, please use the following:

Frequency Band
(MHz)

| Duplexer| Transmit Frequency
(MHz)| Receive Frequency
(MHz)
---|---|---|---
700| 700MHz| 770|

800

800

| 800MHz| 855| 810
VHF | VHF| 136|

141

UHF 380-450

| UHF 380-430MHz
(9.5-10.5MHz Tx to Rx Separation)| 380| 390
UHF 450-470| UHF 450-470MHz| 450|

455

NOTE: This will allow the quoting process to continue but the order cannot be placed until the exact frequencies have been entered.

OR

Use the “ For Quoting Purposes ” field and set it to “ Yes “.

When “ Yes ” is selected, no PDR8000 frequencies need to be entered to create a quote.| To finalize the quote before moving to an order, select “ No ”, and fill in the frequency information.
---|---
|

Selecting a Frequency Plan

Standard Frequency Plans

When the customer frequencies are known, follow the specified frequency requirements in the set of standard frequency plan diagrams.

Custom Frequency Plans

When customer frequencies cannot meet all of the requirements of a standard frequency plan, this is a custom request. Please contact a Sales Solution Specialist to determine if a custom frequency plan is viable. If viable, a per unit custom charge is applicable.

Standard Frequency Plans

Frequency Band

| Frequency Requirements| Suitcase
(SC)| Rackmount
(RM)
---|---|---|---

700MHz

|

• 30MHz Frequency Pair Spacing 
• 11MHz max bandpass

|

Yes

|

800MHz

|

• 45MHz Frequency Pair Spacing 
• 10MHz max bandpass

|

Yes

|

VHF

|

• 4.5-5.5MHz Tx to Rx separation 
• 0.3MHz max bandpass

|

Yes

| Yes

UHF 380-430MHz

|

• 9.5-10.5MHz Tx to Rx separation 
• 0.3MHz max bandpass

|

Yes

| Yes

UHF 380-430MHz

|

• 4.5-5.5MHz Tx to Rx separation 
• 0.3MHz max bandpass

|

Yes

| Yes

UHF 450-470MHz

|

• 4.5-5.5MHz Tx to Rx separation 
• 0.3MHz max bandpass

|

Yes

|

Yes

Frequency Plans: 700MHz, 800MHz, VHF

*768 in Canada
769 in US
**798 in Canada
799 in US

Note: For Simplex applications, the same Tx/Rx frequency can be used and the frequency pair spacing/separation rules do not apply.

Frequency Plans: UHF 380-430MHz, UHF 450-470MHz

Note: For Simplex applications, the same Tx/Rx frequency can be used and the frequency pair spacing/separation rules do not apply.

Main Models: Dropship to New Part Numbers Mapping

The table below shows the mapping between the old dropship part numbers and the new model and option numbers. To compare a new quote to an older quote with dropship part numbers, each dropship number will map to the following:

• Main Model
  • Duplexer (if applicable)
  • Custom Duplexer (if applicable)
  • Suitcase color
  • V.24/Deployment Profiles/DFSI (if applicable)

Common Options| Dropship #| New Option #| Applicable Product
---|---|---|---
Custom Duplexer| TT06580AA| QA09537AA| Suitcase & Rackmount All Bands
Suitcase Color- Black| TT06281AA| QA09646AA| Suitcase All Bands
Suitcase Color- Yellow| TT06252AA| QA09647AA| Suitcase All Bands
V.24 Wireline Operation| TT06253AA| QA09657AA| Suitcase & Rackmount All Bands
Deployment Profiles Capability| TT06319AA| QA09637AA| Suitcase & Rackmount All Bands
DFSI Operation| TT06582AA| QA09638AA| Suitcase & Rackmount All Bands
VHF 50W Amplifier| TT03936A| QA09640AA| Rackmount VHF
UHF 380-430MHz 50W Amplifier| TT3937A| QA09641AA| Rackmount UHF 380-430MHz (Not for sale in Canada)
UHF 450-470MHz 50W Amplifier| TT3938A| QA09642AA| Rackmount UHF 450-470MHz (Not for sale in Canada)
Alarm Capability| TT3935A| QA09608AA| Rackmount All Bands
700MHz| Dropship #| Main Model| Suitcase or Rackmount Option| Duplexer Option
---|---|---|---|---
Suitcase + No Duplexer| TT3152A + TT06261AA| T93USS9PW1AN| QA09644AA|
Suitcase + Duplexer| TT3152A + TT06259AA| QA09655AA or QA09656AA
(based on approx qty)
800MHz| Dropship #| Main Model| Suitcase or Rackmount Option| Duplexer Option
---|---|---|---|---
Suitcase + No Duplexer| TT3153A + TT06261AA| T93VSS9PW1AN| QA09644AA|
Suitcase + Duplexer| TT3153A + TT06260AA| QA09660AA or QA09661AA
(based on approx qty)
VHF| Dropship #| Main Model| Suitcase or Rackmount Option| Duplexer Option
---|---|---|---|---
Suitcase + No Duplexer| TT3148A + TT06261AA| T93KSS9AW1AN| QA09643AA|
Suitcase + Duplexer| TT3148A + TT06254AA| QA09650AA
Rackmount + No Duplexer| TT4079A + TT06583AA| Depending on combination of Duplexer, PA and Alarm, one of the following:
QA09645AA QA09677AA QA09688AA QA09669AA
QA09670AA QA09671AA QA09672AA QA09673AA |
Rackmount + Duplexer| TT4079A + TT06584AA| QA09650AA + QA09770AA
UHF 380-430MHz| Dropship #| Main Model| Suitcase or Rackmount Option| Duplexer Option
---|---|---|---|---
Suitcase + No Duplexer| TT3149A + TT06261AA| T93PSS9PW1AN| QA09643AA|
Suitcase + Duplexer
9.5-10.5MHz TxRx Sep| TT3149A + TT06255AA| QA09650AA
Suitcase + Duplexer
4.5-5.5MHz TxRx Sep| TT3149A + TT06256AA
Rackmount + No Duplexer| TT4080A + TT06583AA| Depending on combination of Duplexer, PA and Alarm, one of the following:
QA09645AA QA09677AA QA09688AA QA09669AA
QA09670AA QA09671AA QA09672AA QA09673AA|
Rackmount + Duplexer
9.5-10.5MHz TxRx Sep| TT4080A + TT06585AA| QA09650AA + QA09771AA
Rackmount + Duplexer
4.5-5.5MHz TxRx Sep| TT4080A + TT06586AA
UHF 450-470MHz| Dropship #| Main Model| Suitcase or Rackmount Option| Duplexer Option
---|---|---|---|---
Suitcase + No Duplexer| TT3150A + TT06261AA| T93RSS9PW1AN| QA09643AA|
Suitcase + Duplexer| TT3150A + TT06257AA| QA09651AA or QA09652AA
(based on approx qty)
Rackmount + No Duplexer| TT4081A + TT06583AA| Depending on combination of Duplexer, PA and Alarm, one of the following:
QA09645AA QA09677AA QA09688AA QA09669AA
QA09670AA QA09671AA QA09672AA QA09673AA|
Rackmount + Duplexer| TT4081A + TT06587AA| QA09651AA or QA09652AA
(based on approx qty) + QA09771AA

Standalone Accessories

Feature Licenses

NOTES: All serial numbers must be provided at the time of order. Add a document containing the full list of serial numbers for each license being ordered to the quote. Quote page- >Order Info tab-> Additional Document #1
Feature license(s) are not transferable between units and if lost, must be re- purchased.

Name| Description| Option #
(Old Dropship#)
---|---|---
V.24 Wireline| Enable V.24 wireline operation
Supports P25 Digital channels only| HKVN4983A
(DDN2634A)
Deployment Profiles Capability| PDR8000® can be programmed with up to ten different Deployment Profiles, each uniquely defining the operational characteristics of the PDR8000®.| HKVN4982A
(DDN2633A)
DFSI Operation| Provides P25 standard IP wireline fixed station interface.
DFSI Protocol Version 1 on the Ethernet interface.
Supports P25 Digital, Analog and Mixed-Mode channels| HKVN4981A
(DDN3285A)

Cables

NOTE: Additional information (serial number) is required when submitting an order for an Auxiliary Cable. Refer to section When Additional Information Is Required for a Standalone Accessory for more information

Name| Description| Option #
(Old Dropship#)
---|---|---
Programming Cable| For use with suitcase and rackmount models
Details: USB A to USB B, 10ft   (PN AK672-3-R)| VKN0039A (DDN9025A)
Auxiliary Cable

SPARE

| For use with suitcase model
Provides control between the PDR8000® and a Booster Pack
Details: 8-Pin on PDR8000® end for R4.0 and newer   (PN 7W088X12-02)
NOTE: For Required Order Information, when ordering a spare cable at the same time as the main PDR8000 unit, use the serial number 12345678| VKN0023A (DDN2333A)
AC Power Cable

SPARE

| For use with suitcase model
Details: 6ft   (PN NKPF-515-D-2)| VKN0019A (DDN2300A)
DC Power Cable

SPARE

| For use with suitcase battery backup (VPN0001A)
Details: 8ft   (PN 7W088X11-01)| VKN0020A (DDN2301A)
DC Power CableUnterminated

SPARE

| For use with suitcase model
Details: 8ft   (PN 7W088X11-02)| VKN0021A (DDN2332A)

Suitcase Accessories

NOTE: Additional information (serial number) is required when submitting an order for a Booster Pack. Refer to section When Additional Information Is Required for a Standalone Accessory for more information.

NOTE: For Required Order Information, when ordering a Booster Pack at the same time as the main PDR8000 unit, use the serial number 12345678.

PDR8000® and a Booster Pack

• 8-Pin on PDR8000® end (PN 7W088X12-02)

| VTD0001A (DDN2732A)
UHF 380-430MHz Booster Pack

Not available for sale in Canada

| Includes Auxiliary Cable which provides control between the PDR8000® and a Booster Pack

• 8-Pin on PDR8000® end (PN 7W088X12-02)

| VTE0003A (DDN2733A)
UHF 450-470MHz Booster Pack

Not available for sale in Canada

| Includes Auxiliary Cable which provides control between the PDR8000® and a Booster Pack

• 8-Pin on PDR8000® end (PN 7W088X12-02)

| VTE0005A (DDN2734A)
700/800MHz Booster Pack

Not available for sale in Canada

| Includes Auxiliary Cable which provides control between the PDR8000® and a Booster Pack

• 8-Pin on PDR8000® end (PN 7W088X12-02)

| VTF0001A (DDN2735A)
Suitcase Battery Backup| Includes Universal Charger
Includes DC Power Cable (PN 7W088X11-01)
Battery Lifetime: 7.5hrs for PDR8000® or 3.5hrs for Booster Pack (50:50 TX-RX Duty Ratio)| VPN0002A (DDN2336A)
Battery Backup Charger| | VPN0001A (DDN2334A)
Zippered Pouch| For accessory cables (PN 3Y088B01-01)| VLN0001A (DDN2335A)

Suitcase Mag Mount Antennas- Unity Gain (0dBd)

Name| Description| Option #
(Old Dropship#)
---|---|---
VHF Unity Gain Mag Mount Antenna| 136 – 174MHz| VAD0003A
(DDN9014A)
UHF Unity Gain Mag Mount Antenna| 380 – 520MHz| VAE0003A
(DDN9015A)
700/800MHz Unity Gain Mag Mount Antenna| 764 – 869MHz| VAF0003A
(DDN9016A)

Suitcase Duplexers

NOTE: Additional information (frequencies) is required when submitting an order for a duplexer. Refer to section When Additional Information Is Required for a Standalone Accessory for more information

Name| Description| Option #
(Old Dropship#)
---|---|---
700MHz Duplexer

SPARE

|

• 30MHz Frequency Pair Spacing 
• 11MHz max bandpass

|

VFE0010A (DDN2318A)

800MHz Duplexer

SPARE

|

• 45MHz Frequency Pair Spacing 
• 11MHz max bandpass

|

VFE0011A (DDN2319A)

VHF Duplexer

SPARE

|

• 4.5-5.5MHz Tx to Rx Separation 
• 0.3MHz max bandpass

|

VFD0020A (DDN2313A)

UHF 380-430MHz Duplexer

SPARE

|

• 9.5-10.5MHz Tx to Rx Separation 
• 0.3MHz max bandpass

|

VFE0012A (DDN2314A)

UHF 380-430MHz Duplexer

SPARE

|

• 4.5-5.5MHz Tx to Rx Separation 
• 0.3MHz max bandpass

|

VFE0013A (DDN2315A)

UHF 450-470MHz Duplexer

SPARE

|

• 4.5-5.5MHz Tx to Rx Separation 
• 0.3MHz max bandpass

|

VFE0009A (DDN2316A)

Custom Duplexer

SPARE

| Any band|

VFN0015A

Training

Name| Description| Option #
(Old Dropship#)
---|---|---
Basic Training
(1 Day)| Includes soft copy of training materials. Customized training available subject to content and price negotiation.

Training the Trainer/End User
Provides a general overview of Mobile Repeater solutions with respect to the agency’s particular use case. Best practices highlighted for common deployment scenarios. Participants will receive hands-on training for practical operation and control.

Requirements: a minimum of 1 PDR8000®.

OR

Technical and Programming Training
Provides radio technicians an in-depth understanding on how the PDR8000® is integrated into the everyday operation of the agency.
Focuses on code plug compatibility, Futurecom Repeater Configurator (FRC) software functionality and programming for optimal end user experience.

Requirements: a minimum of two fully functioning Portable radios (PSUs) programmed to the PDR8000® and one PDR8000®.

Requirement: Contact debra.oster@motorolasolutions.com or maria.tabladillo@motorolasolutions.com from the Worldwide Education organization to coordinate a training session. Please note that the lead time is ~180 days.

|

PSV01S04246A (DDN3699A)

Extended Training| 1 additional day of on-site and/or virtual training

Requirements: Basic Training

|

PSV01S04247A (DDN3700A)

Warranties

NOTE: Warranties can be ordered as standalone up to 90 days after product purchase through after the fact purchase process.

LSV01S04107A

Essential Services with Accidental Damage| Available for suitcase; 3/5/7 year duration|

LSV01S04110A

When Additional Information Is Required for a Standalone Accessory

Step 1. Search for the Standalone Item from the Product Selection page or from the Quote page

Step 2. Select the item and enter a quantity. A reminder appears below the item when additional information is required.

Example Screenshot

Step 3. At the top left of the page, there is a tab for REQUIRED ORDER INFORMATION where the additional information (frequencies or serial numbers) must be entered. The valid range and format for each value is indicated in the Help text provided for each.

NOTE 1: There is a delay of approx 20 seconds after entering each value. This is a known issue and the team is working to address this as quickly as possible.

NOTE 2: When selecting multiple standalone accessories to add to a quote, select all items before filling in the Required Order Information. The Text Values will not line up with the correct Item numbers if items are added after values are entered.

Example Screenshot

Documents / Resources

| MOTOROLA SOLUTIONS PDR8000 Portable Digital Repeater [pdf] User Guide
PDR8000, PDR8000 Portable Digital Repeater, Portable Digital Repeater, Digital Repeater, Repeater
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>