Bavonar XS-610 30000mAh Battery Pack Phone Charger Power Bank User Manual

Bavonar XS-610 30000mAh Battery Pack Phone Charger Power Bank

Product Information

The XS-610 is a portable power bank designed for charging electronic devices on the go. It is equipped with a Li-Polymer battery and features multiple input and output ports, including USB-A1, USB-A2, Type-C, and Micro USB. The power bank has a solar charging capability and comes with LED indicators to display the battery power status.

Schematic

1. Output(USB-A1)
2. Output(USB-A2)
3. Input(Type-C)
4. Input(Micro)
5. Solar charging indicator light / LED power indicator light
6. Solar panel
7. Switch

Specifications

• Product Model: XS-610
• Battery Type: Li-Polymer
• Solar Charging: 5.5V/250mA
• Input(Type-C): 5V/2A
• Input(Micro): 5V/A
• Output(USB-A1): 5V/2.1A
• Output(USB-A2): 5V/2.1A
• Charging Time: About 14 hours (Using a 5V/2A adapter)
• Working Temperature: 0°C-45°C
• Product Size: L142×W72×H27(mm
• Product weight: ≈430g

Product Usage Instructions

Product Boot
This power bank has an automatic detection and identification function. When connecting a device, it will automatically start. In case the device is not automatically recognized, press the switch button to start it manually.

Battery Power Indicator **

**

To check the remaining power of the battery, short press the switch button once.

The LED power indicator will display the power status as follows:

• 0% – Light off
• 1%-25% – Light on
• 25%-50% – Light on
• 50%-75% – Light on
• 75%-100% – Light on

Charging the Power Bank through Power Adapter **

**

This power bank can be charged using either the Type-C input port or the Micro USB input port. Connect the power bank to a phone power adapter using the appropriate cable. The LED power indicator will flash while charging, and all 6 LED indicators will remain on when the power bank is fully charged.

Charge the digital electronics by cable
The power bank has 2 USB-A Outputs, connect the digital product with any output port, it can charge for the digital product, when the digital product is full charged, the power indicator turn off, auto disconnect.

Low Battery Alarm
When the battery power is less than 10%, the power bank will enter low voltage alarm mode. The first LED power indicator will start blinking. If you continue to charge other devices, the LED indicator will keep blinking until the power bank shuts down due to lack of power. If there is no charging device connected, the LED indicator will stop blinking after 30 seconds.

Charging the Power Bank through Sunlight
To charge the power bank using solar energy, place the power bank’s solar panel under direct sunlight or in a sunny environment (avoid high temperatures as it may damage the battery). The solar charging indicator will turn green, indicating that the power bank is being charged by sunlight.

Please Know:

The solar panel’s output power depends on the panel’s power itself and sunlight irradiate intensity etc. Due to the natural limitation such as day and night, seasons, geographical latitude, altitude and sunny, cloudy, raining random factors, so the solar irradiance on the ground is unstable, intermittent. During 10:00 AM to 3:00 PM, the atmospheric mass is AM 1.5, irradiate intensity is 1000W/M2, temperature is 25℃, solar panel’s output power reach the maximum under this condition.

Precautions

• Ensure to fully charge the power bank before first-time use.
• If there is any swelling, leakage, deformation, immersion in water, or short circuit, stop using the power bank immediately.
• Avoid using or exposing the device to high temperatures, moisture, or strong magnetic environments.
• Keep the power bank out of reach of children.
• Avoid leaving the power bank on the car dashboard as it may get damaged due to strong sunlight.
• Do not insert any debris into the input or output ports to prevent damage or short circuits.
• Use standard or original packaged charging cables and power adapters to avoid any potential issues.
• Do not use an all-in-one cable to charge multiple devices simultaneously as it may damage the power bank.
• Before charging, ensure that your device’s input voltage matches the power bank’s output voltage.
• If the power bank is left unused for a long time, fully charge and discharge it at least every [insert recommended time period] to maintain its performance.
• Full charge the product with your first time use；
• Don’t hit the device or use it in the high temperature, moist, strong magnetic environment；
• Please put the power bank on the place where kids can’t reach；
• Don’t leave the product on the car dashboard, the high temperature will damage the device cause by strong sunlight irradiation；
• Don’t throw any debris in the input output ports, or it may cause damaged or short circuit；
• Avoid the unusual results happen, please use the standard or original packaged charging cable, power adapter etc；
• Don’t use the all in one cable to charge multi devices simultaneously, it may cause damage to the power bank；
• Please confirm whether you device input voltage is the same with the power bank’s output voltage before charging；
• Over discharge may occur if long time lay aside, in order to not affect the performance, please full charge and discharge the power bank at least every 3 months.

Frequently Asked Questions (FAQ)

1. Q: How long does it take to fully charge the power bank using a 5V/2A adapter?
   A: It takes approximately 14 hours to fully charge the power bank using a 5V/2A adapter.

2. Q: Can I charge multiple devices simultaneously using the XS-610 power bank?
   A: It is not recommended to charge multiple devices simultaneously using an all-in-one cable as it may cause damage to the power bank. It is best to charge one device at a time.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>