SA One Piece Toilet Installation Guide

: June 30, 2024
: Support

Table of Contents

TOOLS AND MATERIALS REQUIRED
CARE AND MAINTAINANCE
SERVICE AND SUPPORT
Read User Manual Online (PDF format)
Download This Manual (PDF format)

SA One Piece Toilet

TOOLS AND MATERIALS REQUIRED

A. Water Supply Kit ( Not needed if replacing existing toilet)
B. Adjustable Wrench
C. Flathead Screwdriver
E. Nut Driver or Socket Set
F. Putty Knife
G. Tape Measure

Handling

Toilets can be heavy! Please handle carefully – it may be a two-person job. If you have a one-piece toilet, support the bowl with one arm and the tank with the other. If you have a two-piece toilet, move the parts separately to avoid damaging them.

Removing Your Old Toilet

Turn off the water supply.
Flush the toilet to empty the tank, remove any water left in tank or bowl.
Disconnect the supply line from the tank.
Remove decorative caps. Unscrew nuts that attach the toilet to the floor.
Remove toilet.
Make sure the water supply valve is shut off before installation.
Remove old closet bolts from closet flange. Clean any old wax, putty, etc from base area.

Important Note Regarding Water Supply:

Before installation, please ensure that the shut off valve is greater than 7.5″ from the center of the drain to the center of the shut off valve one either side.

Note

This is a true 12″ rough-in toilet from finished wall to center of the drain (no less than 12″). Baseboard thickness may reduce the rough-in dimension.

One Piece Toilet Installation Procedure

Step 1. Install new floor bolts to the floor flange.
Step 2. Attach flexible water supply line to the inlet of the fill valve and hand tighten only. At this point, DO NOT connect to the water shut-off valve.
Step 3. Place a new wax ring around the water flange of the toilet bowl.
Step 4. Lower the toilet onto the closet bolts, so the bolts project through mounting holes in base of toilet. Using a rocking motion, press the bowl down to position the toilet onto the flange.
Step 5. Install plastic cap washers, followed by metal washers and nuts onto the closet bolts. Tighten the bolts alternately until toilet is firmly seated on the floor. CAUTION: DO NOT OVERTIGHTEN NUTS, SEVERE DAMAGE MAY OCCURE.
Step 6. Install the plastic cap covers.
Step 7. Connect the flexible water supply line (not included) to the shut off valve. Tighten coupling nuts securely.

Connect Water Supply

Connect water supply line (new or existing) between shut off valve and tank inlet water fitting. Tighten coupling nuts securely. NOTE: DO NOT OVERTIGHEN
Turn on supply valve and allow tank to fill until float rises to shut off position.
Check for leakage at fittings, tighten or correct as needed.

CARE AND MAINTAINANCE

DO NOT

Do not stand on the toilet cover, and do not place heavy objects on it. (Or else it may cause crack)
Do not clean the toilet seat with household cleaners, volatile, thinner and eradicator, or use nylon brush, and avoid chlorine-containing, corrosive and a abrasive cleaners. Maintain the shiny surface by using soft fabric and clean water. (Or else it may cause abrasion or crack)
Do not let child play the toilet cover, to avoid hurting fingers and other accident.

DO

Clean or wash it with neuter cleaners ( such as soap powder). And then dry it with clean fabric.
Open and close toilet seat cover tenderly. Toilet seat and cover both have the function of slow closing.
Wipe outside of the toilet gently with a damp cloth and blot dry with a soft towel. Make sure that the complete surface is cleaned and completely dry.
NOTE: IMPROPER CARE MAY CAUSE THE WARRANTY TO BECOME INVALID.

SERVICE AND SUPPORT

If any defects in materials or workmanship are discovered during normal use within six months of installation, we will provide replacement parts free of charge, subject to normal installation, use, repair or maintenance.

This warranty applies to: Original purchaser only, proof of purchase is required when making a claim.

We recommend that all toilet installations be performed by a professional (a licensed professional plumber or contractor).

We will not be responsible for any damage or product failure caused by improper installation, misuse, or failure to hire a licensed professional for installation. We are not responsible for any installation or removal costs.

The half-year limited warranty will be void if:

Installer failed to follow installation recommendations
The product has been moved from its original installation location
The packaging condition of the product has been modified in any way
The product has been subject to improper maintenance, abuse, misuse, excessive use of chemicals, accidents or other damage.

This toilet does not imply that the product complies with any local building or plumbing requirements code. It is the consumer’s responsibility and obligation to determine compliance with local regulations before and during installation.

If you have any questions or concerns, please contact us directly: servicefast1@outlook.com