CP9104Q Pencil Grinder User Manual

: May 15, 2024
: Support

Table of Contents

CP9104Q Pencil Grinder
Air Supply Requirements
Maintenance
Technical Data
Noise & Vibration Declaration
MANUFACTURER’S LIMITED WARRANTY
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

CP9104Q
Pencil Grinder
Operator’s Manual CP9104Q Pencil Grinder INSTRUCTION MANUAL

CP9104Q Pencil Grinder

WARNING
To reduce risk of injury, everyone using, installing, repairing, maintaining, changing accessories on, or working near this tool must read and understand these instructions before performing any such task.
LOCAL SALES AND SERVICE LOCATIONS
Please fi nd your local contact at: www.cp.com

Machine Type:
Power tool equipped with 1/8in. or 3mm collet chuck for use with various burrs for polishing and grinding – No other use is permitted.

Air Supply Requirements

Supply tool with 90 psig (6.3 bar) of clean, dry air. Higher pressure drastically reduces tool life.
Connect tool to air line using pipe, hose and fitting sizes shown in the diagram below.
Do not install a quick coupler directly into the sander throttle handle.

Lubrication
Use an air line lubricator with SAE #10 oil, adjusted to two drops per minute. If an air line lubricator cannot be used, add air motor oil to the inlet once a day.

Maintenance

After first year disassemble and inspect tool every three months if the tool is used every day. Replace damaged or worn parts.
High wear parts are underlined in the parts list

Technical Data

1/8in. or 3mm Collets
Free speed; 60,000 RPM
Air pressure 90 psi (6.3 bar)
Air comsumption; 7 cfm (3.3 l/s)

Noise & Vibration Declaration

Sound pressure level 71 dB(A), uncertainty 3 dB(A), in accordance with EN ISO 15744. For sound power, add 11 dB(A).
Vibration value; <2.5 m/s², re. ISO 20643.
Declaration of noise and vibration emission
All values are current as of the date of this publication. For the latest information please visit cp.com.
These declared values were obtained by laboratory type testing in accordance with the stated standards and are suitable for comparison with the declared values of other tools tested in accordance with the same standards. These declared values are not adequate for use in risk assessments and values measured in individual work places may be higher. The actual exposure values and risk of harm experienced by an individual user are unique and depend upon the way the user works, the workpiece and the workstation design, as well upon the exposure time and the physical condition of the user.
We, Chicago Pneumatic, cannot be held liable for the consequences of using the declared values, instead of values reflecting the actual exposure, in an individual risk assessment in a work place situation over which we have no control.
This tool may cause hand-arm vibration syndrome if its use is not adequately managed. An EU guide to managing hand-arm vibration can be found at http://www.humanvibration.com/EU/VIBGUIDE.htm
We recommend a programme of health surveillance to detect early symptoms which may relate to noise or vibration exposure, so that management procedures can be modified to help prevent future impairment.

MANUFACTURER’S LIMITED WARRANTY

Limited Warranty: The “Products” of the Chicago Pneumatic Tool Co. LLC (“CP”) are warranted to be free from defects in material and workmanship for one year from the date of purchase. This Warranty applies only to Products purchased new from CP or its authorized dealers.
Of course, this Warranty does not apply to products which have been abused, misused, modified, or repaired by someone other than CP or its Authorized Service Representatives. If a CP Product proves defective in material or workmanship within one year after purchase, return it to any CP Factory Service Center or Authorized Service Center for CP tools,transportation prepaid, enclosing your name and address, adequate proof of date of purchase, and a short description of the defect. CP will, at its option, repair or replace defective Products free of charge. Repairs or replacements are warranted as described above for the remainder of the original warranty period. CP’s sole liability and your exclusive remedy under this Warranty is limited to repair or replacement of the defective Product. (There Are No Other Warranties Expressed Or Implied And CP Shall Not Be Liable For Incidental, Consequential, Or Special Damages, Or Any Other Damages, Costs Or Expenses Excepting Only The Cost Or Expense Of Repair Or Replacement As Described Above.)

Original Instructions
Copyright 2010, Chicago Pneumatic Tool Co. LLC
All rights reserved. Any unauthorized use or copying of the contents or part thereof is prohibited. This applies in particular to trademarks, model denominations, part numbers and drawings. Use only authorized parts. Any damage or malfunction caused by the use of unauthorized parts is not covered by Warranty or Product Liability.