MGI Zip Series Zip X3 Navigator User Manual
- June 3, 2024
- MGI
Table of Contents
- Registration
- What’s Included
- Assembling Your Zip X3
- Battery Charging & Connection
- Fitting the Golf Bag
- Front Wheel
- Operating the Digital Top Box
- Adjusting and Aligning the Front Wheel
- Warranty
- Preventative Maintenance Program
- Service and Repair Centres
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
MGI Zip Series Zip X3 Navigator
Registration
It is most important you register your MGI Zip X3 online immediately as registration:
- Records your Zip X3 for warranty purposes
- Speeds up any servicing required on your Zip X3
- Assist us to contact you with any updates to your Zip X3
To register your Zip X3, visit www.mgigolf.com
You will need to record your MGI serial number. This is found on the Zip X3
battery base or in the top box compartment.
Please keep this user manual on file for your own reference and a copy of your
serial number;
My MGI Zip X3 Serial Number is
[example AZX3V1173401234]
Purchased Date
You may be required to show proof of purchase so we recommend you keep your receipt with this manual.
What’s Included
- MGI Zip X3
- 24v Lithium Battery
- Battery Charger
- GPS Holder
- MGI Pouch with:
- User Manual Accessory Guide
Assembling Your Zip X3
Attaching the Rear
Wheels First, lubricate both axles using the black grease cloth provided in
the box. Lubrication of the axles should be performed regularly to keep your
cart in optimal condition.
Step 1. Each wheel is labelled with L or R for left or right. This is very important as the wheels must be placed on the correct side of the Zip X3. Left or right sides are determined when standing behind the Zip X3 as pictured below.
Step 2. On the wheel, press the grey release button on the wheel hub.
Place the wheel onto the axle.You will notice you need to match up the inner
female groove on the axle and the male of the wheel. When placed in position
simply release the button. You will notice you hear a “click” when the wheel
is properly secured. To check that the wheel is properly in position pull on
the wheel. If it is properly in position it will not slide off. Repeat for the
other wheel. Rear
Wheels Positions
The MGI Zip X3 is designed to allow the rear wheels to be in two positions.
The position is determined by where the wheel is locked on the axle in either
of the two grooves [see picture]. The drive position is used during the normal
operation of the Zip X3. The free wheel position is used to freely push the
Zip X3 should you experience battery or Zip X3 issues on the course.
Drive position
i. Drive position Lock the wheel onto the groove closest to the battery
base.To do this, press the grey release button on the wheel hub, push the
wheel on to the axle as far as possible. To test for drive position try
rolling the wheel backwards. If you feel resistance then the wheel is now in
drive position and ready to use. Repeat for both wheels. ii. Free wheel Lock
the wheel into the groove closest to the end of the axle. To do this, press
the grey release button on the wheel hub, push the wheel on to the axle and
release the release button onto the groove.To test for free wheel position try
rolling the wheel backwards. The wheel should spin freely with no resistance.
Repeat for both wheels.
Unfolding
Please see below the steps to unfold a Zip X3 Handle.
Step 1: Ensure both rear
Step 2: Release Fold Lever. wheels are attached.
Step 3: Move Top Bag Support away from front wheel assembly until you hear it
click.
Step 4: The handle is now free to pull upwards. The handle will naturally
unfold as you continue to pull until the handle is completely open.
Step 5: Ensure that the latch at the bottom of the handle clicks into place.
Step 6: Close the fold lever to lock the handle into place in one of three
positions.
Step 7: Push the top bag support down to move it into position.
Folding
Step 1: Disconnect the battery by lifting the battery handle. It can be left
on or removed from the Zip X3.
Step 2: Open the fold lever to release the handle.
Step 3: Pull up the latch at the bottom of the handle.
Step 4: Lower the handle down flat.
Step 5: Push the toggle down on the top bag support and then move the Top Bag
Support down so that it locks over the front wheel assembly.
Step 6: Close the fold lever to lock the handle into place.
Fourth Foldable Rear Wheel
The MGI Zip X3 comes standard with a fourth foldable rear wheel. This wheel
MUST be unfolded into position at all times when the Zip X3 is in use. This
will reduce damaging the Zip X3, and provide the ultimate in stability across
all terrains.This fourth wheel should be cleaned regularly with a cloth to
ensure it can be folded as required for storage.
GPS Holder and Top Handle Compartment
In the top handle compartment there is a position for a GPS/ mobile device
holder. Open the compartment and connect the holder into position. To open the
holder always press the button at the top of the holder. Place the GPS into
the cradle, then close the holder by squeezing the two sides closer together
.
Inverting Rear wheels
The rear wheels can be inverted on the axle to reduce the size of the Zip X3
when folded.To invert the rear wheels, press the grey release button on the
wheels hub and remove from the axle. Invert the rear wheels so that the wheels
hub protrudes away from the axles. Press the grey release button on the wheels
hub and release once the wheel is fitted onto the axle.
Battery Charging & Connection
The Zip X3 is designed to take either Zip battery:
- MGI 24v 250Wh Lithium battery [Standard]
- MGI 24v 380Wh Lithium battery [Optional]
Initial Charge
- Before using your MGI Zip X3 for the first time you must fully charge the battery overnight.
- Plug the charger AC lead into a power point – the Green LED illuminates to indicate the charger is power on.
- Plug the charger output connection into the connector on the front of the battery – the Red LED illuminates to indicate charging.
- When the charging LED indicator has turned green, the battery is fully charged and ready to be used.
- Please refer to the battery charger user manual for further information.
Connecting the Battery onto the Zip X3
Position the battery on the Zip X3 and push the battery down to secure it.
Push the handle down to connect the battery to the Zip X3. Your Zip X3 has
been equipped with fail safe battery connection, so the Zip X3 will not move
when you connect the battery.Your Zip X3 will only start once the speed
control is switched on.
Charging the Battery after Use
- Disconnect the battery by lifting the handle.
- The battery can be left on or removed from the Zip X3 for charging.
- Plug the charger AC lead into a power point – the Green LED illuminates to indicate the charger is power on.
- Plug the charger output connection into the connector on the front of the battery – the Red LED illuminates to indicate charging.
- When the charging LED indicator has turned green, the battery is fully charged and ready to be used.
Fitting the Golf Bag
Ensure that the top bag support straps are disconnected. Position the golf bag on the Zip X3. Secure the top bag support strap
- Select a good position for the elasticised straps to be put around the golf bag
- Stretch the longer end of the strap and loop the rounded plastic bar underneath the hook on the shorter end
- The top bag support straps should now be connected.
Please ensure the top bag support straps are hooked in place securely before releasing. Failure to do so could result in injury to the user. Adjusting the length of the top bag support strap The rounded plastic bar on the longer strap can be adjusted to ensure the bag is secured properly in place. Secure the lower bag strap Pull the lower bag strap over the base of the golf bag
Front Wheel
Unlocking & Locking the Front
Wheel The front swivel wheel can be set in two positions.
- Unlocked position to allow for 360° swivel for optimum turning ability. Move the knob, on top of the front wheel assembly, to the left hand side.
- Locked position is best when using the Controlled Distance function. Move the knob, on top of the front wheel assembly, to the right hand side.
Operating the Digital Top Box
Top Box Display
- Distance Mode Button
- Unit Setting Button
- ON / OFF Speed Control Button
- Speed Setting Indicator
- Battery Level Indicator
- Distance Mode
- Distance
- Unit Measurement
Start / Stop the Zip X3
Speed Control
Zip X3 Speed Control Please note the following points regarding the Zip X3 Speed Control.
-
To select the desired speed, rotate the speed control button. Turning the speed control button clockwise will increase the speed, whilst anti-clockwise will decrease speed.
-
The speed setting chosen is displayed in the centre of the coloured screen.
Please note you will feel notches as you rotate the speed control. The notches do not indicate a change in speed. The speed will only increase or decrease as the number changes in the display. -
To start the Zip X3 at this desired speed, tap the top of the speed control button.
-
Another tap will stop the Zip X3.
-
The desired speed can be altered up or down while the Zip X3 is moving.
Turn the Zip X3 Off
Zip X3 Battery Please note the following points regarding the Zip X3 Battery.
Connecting the Battery onto the Zip X3
-
Position the battery on the Zip X3 and push the battery down to secure it. Push the battery handle down to connect the battery to the Zip X3.
-
To turn the Zip X3 Top Box Display off: Hold down the Start/Stop Speed Control Button and Left Hand Distance Mode Button for four seconds and the display will turn off thereby disabling the Top Box.
Please note that the battery will still be connected to the Zip X3 and will continue to drain whilst connected. -
Please note that the Zip X3 display will also turn off if the Speed Control is not operated for 30 minutes.
Once again, please note that the battery will still be connected to the Zip X3 and will continue to drain whilst connected. -
To reactivate the Top Box Display, whilst the battery is connected, hold down the Start/Stop Speed Control Button and Left Hand Distance Mode Button for four seconds and the display will turn on thereby enabling the Top Box.
-
To fully shut down the Zip X3 and prevent the battery from discharging, disconnect the battery by lifting its handle. The battery can be left on or removed from the Zip X3.
Battery Level Indicator
Battery indication is located on the left side of the top box screen. Four
coloured bars are highlighted showing full charge. The lesser number of bars
displayed, means there is less battery life available.You should always check
the battery status before you play golf to ensure the four bars are there.
Unit Measurements
You can move from meters / kilometres to yards / miles simply by pressing the
Unit Setting Button [on the right].
Distance Modes
There are three distance measurement modes.To move between the modes by
pressing the Distance Mode Button [DM] [on the left] Distance A and B:
resettable distance measurements could be used to measure how far you hit your
shot and to measure how far you have walked for the day. To reset, simply
press the DM Button [left side] for 3 seconds until the reading displays “0”.
Distance Total: cannot be reset as it is the Odometer for the life of the Zip
X3.This feature will assist with service reminders which are recommended at
each 500kms (310 miles) or 6 months periods.
Control Distance
- Function The Control Distance Function enables the MGI Zip X3 to be sent a preset distance before the Zip X3 auto stops. To use this function:
- It is recommended that you lock the front wheel to ensure the Zip X3 tracks in a straight line.
- Press and hold down Speed control button for 3-4 seconds until the speed setting changes to 5 [metres or yards] and “ADC MODE” will appear.
- Turn the Speed control button clockwise to increase the distance or anti-clockwise to decrease the distance until the desired distance is achieved between 5-60 [metres or
- yards].
- Always look ahead and assess the condition of the terrain of where you want to send the Zip X3 prior to doing so.
- Once the desired distance is reached, press the Speed control button once to send the Zip X3 off to the desired distance.
Competition Mode
In the unlikely event the club you are playing at does not allow the use of
distance devices you will need to disable the distances feature on the MGI Zip
X3. To disable the distance recording feature, simply hold down the left and
right buttons at the same time for 3 seconds and “COMP MODE” will appear on
the screen. In addition, the distance recording will be removed from the
screen. To exit COMP MODE hold down the left and right buttons at the same
time.
Adjusting and Aligning the Front Wheel
Each Zip X3 is checked for straight tracking prior to leaving the factory. In the unlikely event the Zip X3 is not tracking straight, the front wheel can be adjusted to regain straight tracking as follows;
-
Lock the swivelling front wheel [6.0] and run the Zip X3 forward to see if the Zip X3 veers left or right.
-
Unlock the swivelling front wheel, swivel it to see the locking latch in the middle of the two front wheels, as below Picture on Left
-
Unlock the latch by pulling down
-
Adjust the direction by turning the thumb screws in the right hand Picture. Alternate between cogs when adjusting suggest a quarter of a turn at a time To make the Zip X3 go Right – L/H screw anticlockwise, R/H screw clockwise [Up on both sides] To make the Zip X3 go Left – L/H screw clockwise,
R/H screw anticlockwise [Down on both sides] -
Lock the latch by pushing it up.
Please note that there is a process in adjusting the tracking. It is suggested that the users should do a little bit of adjustment, test the tracking and then adjust again until the
Warranty
Warranty Policy
The MGI Zip X3 is covered by a limited 2 year manufacturer’s warranty from the
date of purchase. Duration of this warranty is: 2 years on parts 2 years
on Lithium batteries and chargers MGI or an authorised service centre will
repair or replace any parts found to be defective in materials or workmanship
under normal use provided that:
-
The MGI Zip X3 has been properly used, maintained and regularly serviced [see section 10.5]
-
The replacement or repair is performed by an authorised MGI
service centre or the owner with MGI approval. -
The Zip X3 has been registered online. Our goods come with guarantees that cannot be excluded under Consumer Law. You are entitled to a replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if goods fail to be of acceptable quality and the failure does not amount to a major failure. This warranty is in addition to other rights and remedies available to the consumer under law. The consumer is responsible for expenses associated with a warranty claim. To make a warranty claim, cease using the goods immediately and contact MGI directly using the contact details on the back of this User Manual. Proof of purchase is mandatory.
Warranty Exclusions
The following events will void warranty:
- Any alteration performed by non-authorised people or companies.
- Fitting of parts or accessories not recommended by MGI.
- Any damage caused by continued operation of the product after it is known to be defective.
- Damage to the seat and/or seat support bracket on the unit.
- Damage caused by partial or complete ingress of water into motor/gearbox and other major components.
- Damage caused by the unit being driven into bunkers, other course hazards or clubhouse and carpark hazards.
- Damage caused by golf balls or golf clubs.
- Application of external force to any part of the unit or battery.
- Fusion of motor or electronics through overload or continual stationary operation.
- All implied warranties [save those preserved by statute] are excluded.
- Liability for consequential damages under any and all warranties are excluded to the extent exclusion is permitted by law.
In the event of submersion in water (partial or full) of your Zip X3; MGI
advises the complete write-off of your Zip X3.
The cost of replacing the water-damaged components (including labour) exceeds
the price of a replacement Zip X3.
If you elect to purchase replacement components, i.e. motors, gearbox, motor
controller and electronics, we advise the replacement of ALL components
simultaneously. Replacing individual components on a water-damaged Zip X3
poses a higher risk of future failure of other components and therefore these
parts will not be covered under warranty.
Please note that MGI does not warrant water-damaged batteries and, due to fire
risk, under no circumstances should they continue to be used.
The following events are not covered under warranty:
Normal wear and tear; – (e.g. tyres, rubber handlebar, elastic straps,
paintwork, battery performance, axles threads, charging ports on batteries and
remotes, screen glass etc.) – Minor appearance defects which bear no effect on
the operation of the unit and are considered by the manufacturer to be within
the accepted standards.
Parts Installed During
Warranty Warranty coverage for components installed during a motorised Zip
X3’s warranty period shall consist of the duration of the Zip X3’s warranty
period, provided the warranty installation is performed by MGI, an authorised
service centre or the Zip X3 owner on approval. Replacement of parts under
warranty will not extend the warranty of the Zip X3 or parts.
Preventative Maintenance Program
To properly provide for the continued operation of your MGI Zip X3, MGI has introduced its Preventative Maintenance Program [PMP]. The PMP consists of work to be carried out by both the owner and authorised service centres.To properly maintain the warranty of your MGI Zip X3, it is essential that this work is carried out. If the work carried out by the authorised service centre is to replace parts that are part of the maintenance schedule, the owner will be charged for the parts and labour. If the work to be carried out is part of warranty, MGI will bear the cost.
Cleaning Your Zip X3 [See Maintenance Schedule]
- For years of good operation, your Zip X3 requires care and attention.
- Keep your Zip X3 clean by using a cloth with warm water and a mild detergent.
- Do not hose down your Zip X3 under any circumstance, as the Zip X3 has electronic components.
- Ensure that the seat stem bracket is free from sand.
- Do not submerge your Zip X3 in water as it will cause irreparable damage.
- Clean the Zip X3 battery base when the battery is removed from the Zip X3.
Rear Wheel Axles Maintenance [See Maintenance Schedule]
The rear wheel stub axles need to be lubricated regularly. Remove the rear
wheels by depressing the spring clip and at the same time pull off the wheel.
Apply Petroleum Jelly or light grease to the stub axles. Use a very small
amount as the grease can attract sand. If you play in sandy conditions you
should clean the axle and regrease fortnightly.
Upper and Lower Bag Strap Maintenance [See Maintenance Schedule]
The bag straps should be replaced as per the Service Schedule. The upper bag
strap can be replaced by:
- Removing the left and right hand straps form the upper bag support
- Undo and remove the screws holding the strap in position on the bag support
- Remove and replace both bag straps
- Insert bag strap securing screws.
MGI Service Schedule
It is the owner’s responsibility to ensure that all periodical checks,
necessary adjustments and services are carried out. If in doubt please contact
the MGI service centre: Australia 1300 644 523 USA 1800 617 2990
Any work performed on your Zip X3 should be recorded on your service record (see page 21) regardless of the work.
MGI Zip X3| Monthly| 6
Monthly
| Every 2 yrs| Every 3 yrs
---|---|---|---|---
Wipe down the Zip X3 with a warm cloth after each use [do not hose]|
BO
| | |
Lubricate rear wheel stub axles| BO| | |
Check and tighten nuts and bolts| | BO| |
Check and tighten handle pivots| | BO| |
Check alignment of Zip X3 – ensure that it runs straight| |
BO
| |
Replace Speed Controller and On/ Off switch assembly| | | |
BO /SC
Replace rear and front wheels| | | | BO
Replace upper and lower bag straps| | | | BO
BO = Zip X3 owner can carry out this work
SC = Charged work to be carried by approved service centre
BO/SC = The six monthly service can be completed by either an authorised
service centre or the owner of the Zip X3.
Service and Repair Centres
6 month inspection | Date: Invoice #: | Serviced by: Signature: |
---|---|---|
1 year inspection | Date: Invoice #: | Serviced by: Signature: |
1 ½ year inspection | Date: Invoice #: | Serviced by: Signature: |
2 year inspection | Date: Invoice #: | Serviced by: Signature: |
2 ½ year inspection | Date: Invoice #: | Serviced by: Signature: |
3 year inspection | Date: Invoice #: | Serviced by: Signature: |
3 ½ year inspection | Date: Invoice #: | Serviced by: Signature: |
4 year inspection | Date: Invoice #: | Serviced by: Signature: |
4 ½ year inspection | Date: Invoice #: | Serviced by: Signature: |
5 year inspection | Date: Invoice #: | Serviced by: Signature: |
5 ½ year inspection | Date: Invoice #: | Serviced by: Signature: |
6 year inspection | Date: Invoice #: | Serviced by: Signature: |
Service and Repair Centres
For all servicing, please do not go back to your place of purchase. To find
your nearest Service centre visit www.mgigolf.com
For warranty repairs to be authorised you MUST provide proof of purchase.
Please keep this with you as well as your Serial number you can record in this
manual. It is most important you register your MGI Zip X3 online for warranty
purposes. It is most important you register your MGI Zip X3 online for
warranty purposes.
Purchasing Parts and Accessories
You are welcome to service your Zip X3 out of warranty, by purchasing parts direct from MGI. Please call or email to discuss the right parts and instructions.
Contacting MGI
www.mgigolf.com
MGI AUSTRALIA
Service Email:
customerservice@mgigolf.com
Live Chat : visit www.mgigolf.com
Toll Free within Australia : 1300 644 523 (excludes mobiles) Western
Australia/ Internal phone +61 3 8872 6700
Local Service Centres : visit www.mgigolf.com
MGI USA
Service Email : serviceusa@mgigolf.com
Live Chat: visit www.mgigolf.com
Telephone: 1800 617 2990
MGI GLOBAL
Sales Email : globalsales@mgigolf.com
Service Email: customerservice@mgigolf.com
Live Chat : visit www.mgigolf.com
Contacting Local Agent
Please refer to www.mgigolf.com to find the
distributor in your country.
FAQ
Q : My Zip X3 is not tracking straight.
A : You can do a simple realignment on the two front wheels. See section
Adjusting and aligning the front wheels.
Q: I would like to have my MGI Zip X3 serviced. Who do I call? A: MGI
AUSTRALIA
Visit www.mgigolf.com to find your nearest
service centre using your postcode within Australian and New Zealand. You can
also call MGI Head office using any of the contact details. See Section 13.0
for details. Internationals please call your local agent as per Section
MGI USA Call 1800 617 2990 Email :
serviceusa@mgigolf.com MGI GLOBAL Emai l:
customerservice@mgigolf.com
P: (02) 6652 8816 W: EASTCOASTGOLFCARTS.COM.AU E:
INFO@EASTCOASTGOLFCARTS.COM.AU A: 2/164 PACIFIC HIGHWAY COFFS HARBOUR, NSW
2450
References
- Golf Carts & Buggies | Sales Service Parts Accessories
- Electric Golf Buggy | Best Motorised Golf Carts & Trolley For Sale Australia