TAC 5S-19C1132B 5IN Oval Bent End Sidebar Installation Guide
- June 28, 2024
- TAC
Table of Contents
TAC 5S-19C1132B 5IN Oval Bent End Sidebar
Specifications
- Product Name : 5IN Oval Bent End Sidebar
- Compatibility : 2019-2024 1500 Silverado/Sierra Crew Cab (Includes Diesel Models w/DEF), 2020-2024 2500/3500 Silverado/Sierra Crew Cab (Includes Diesel Models w/DEF)
- Part Number : 5S-19C1132B
Product Usage Instructions
Parts List
- 1 Driver/left Sidebar
- 1 Passenger/right Sidebar
- 16 8-1.25mm x 30mm Hex Bolts
- 16 8-1.25mm x 25mm Combo Bolts
- 8 Mounting Brackets
- 16 8mm Lock Washers
- 16 8mm x 24mm x 2mm Flat Washers
Installation Steps
- Remove contents from the box and verify all parts are present.
- Select a Mounting Bracket and bolt it to the factory threaded holes on the driver/left side using the provided hardware. Do not tighten the hardware at this time.
- Repeat step 2 to install Mounting Brackets on the remaining driver/left side mounting locations.
- Select the Driver/left Sidebar and place it on top of the Brackets without sliding or rotating it.
- Attach the Sidebar to the Brackets using the provided Combo Bolts.
- Level and adjust the Sidebar, then fully tighten all hardware.
- Repeat steps 1-6 to install the Passenger/right Sidebar.
- Periodically inspect the installation to ensure all hardware is secure and tight.
Maintenance
To protect your investment, wax the product after installing. Regular
waxing is recommended for added protection. Avoid using polish or wax with
abrasives that could damage the finish. Aluminum polish can be used for small
scratches, while mild soap is suitable for cleaning.
FAQ
-
Q: Can I install the Sidebar alone?
- A: While it’s recommended to seek assistance, you can install the Sidebar alone by following the provided instructions carefully.
-
Q: How often should I wax the product?
- A: Regular waxing is recommended to maintain a protective layer over the finish. The frequency of waxing may vary based on usage and environmental conditions.
INSTALLATION INSTRUCTIONS
5IN OVAL BENT END SIDEBAR
2019-2024 1500 SILVERADO/SIERRA CREW CAB
(INCLUDES DIESEL MODELS W/DEF)
2020-2024 2500/3500 SILVERADO/SIERRA CREW CAB (INCLUDES DIESEL MODELS W/DEF)
PART# 5S-19C1132B
5IN OVAL BENT END SIDEBAR
2019-2024 1500 SILVERADO/SIERRA CREW CAB (INCLUDES DIESEL MODELS W/DEF)
2020-2024 2500/3500 SILVERADO/SIERRA CREW CAB (INCLUDES DIESEL MODELS W/DEF)
PARTS LIST
| 1 | Driver/left Sidebar | 16 | 8-1.25mm x 30mm Hex Bolts |
|---|---|---|---|
| 1 | Passenger/right Sidebar | 16 | 8-1.25mm x 25mm Combo Bolts |
| 8 | Mounting Brackets | 16 | 8mm Lock Washers |
| 16 | 8mm x 24mm x 2mm Flat Washers |
PROCEDURE
REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. READ INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION. ASSISTANCE IS RECOMMENDED.
- Start the installation under the driver side of the vehicle. Locate the 6 plugs along the bottom edge of the body. Mounting Brackets will bolt to the 1st, 3rd, 4th and 6th threaded mounting holes, (Figures 1—5). Remove the plastic plugs from each mounting location. Directly above each threaded insert is a top mounting location on the side of the body panel. Hold a Bracket up in place to help determine the mounting holes to use along the body. NOTE: Thread an 8mm Hex Bolt into the threaded inserts to clear paint as required.
- Select (1) Mounting Bracket. Starting at the front of the driver/left side, bolt the Mounting Bracket to the factory threaded holes with (2) 8mm Hex Bolts, (2) 8mm Lock Washers and (2) 8mm Flat Washers, (Figures 6 & 7). Do not tighten hardware at this time.
- Repeat Steps 1 & 2 to install (3) Mounting Brackets on the remaining driver/left side mounting locations along the body panel, (Figures 8—10).
- Select the Driver/left Sidebar. Use the illustration above to help determine the correct Sidebar. Place the Sidebar on top of the Brackets. IMPORTANT: Do not slide, (front to back or rotate), the Sidebar on the Brackets or damage to the finish may result.
- . Attach the Sidebar to the Brackets with (8) 8mm Combo Bolts, (Figures 11—15).
- Level and adjust the Sidebar and fully tighten all hardware.
- Repeat Steps 1—6 to install the Passenger/right Sidebar.
- Do periodic inspections to the installation to make sure that all hardware is secure and tight.
To protect your investment, wax this product after installing. Regular waxing
is recommended to add a protective layer over the finish. Do not use any type
of polish or wax that may contain abrasives that could damage the finish.
Aluminum polish may be used to polish small scratches and scuffs on the
finish. Mild soap may be used also to clean the Sidebars.
Driver/left side Installation Pictured
Driver/left side Installation Pictured
Driver/left side Installation Pictured
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>