WATTSHOP M5 Anemoi Adjustable Angled Riser Installation Guide
- May 15, 2024
- WattShop
Table of Contents
M5 Anemoi Adjustable Angled Riser
Installation Guide
M5 Anemoi Adjustable Angled Riser
Anemoi Adjustable Riser (Universal)
Thank you for purchasing our WattShop #Anemoi adjustable angled risers. We
hope they serve you well in achieving maximum performance in all of your
races’ Please share your pictures and results on Facebook, Twitter and
lnstagram using #WattShop
WATTS IN THE BOX
No| Part Description| Quantity| Torque
1| Adjustable riser (upper)| 1 (pair)|
,| Adjustable riser (lower)| 1 (pair)|
| Retaining nuts (front)| 1 (pair)|
| Retaining nuts (rear)| 1 (pair)|
| MSx16rnm grub screw| 4|
| Anti-vibration washer| 4|
7| MSxlOrnrn low cap head bolt| 2| 5E\in-1
8| MSx2Srnm low cap head bolt| | SNrn
9| Barrel nuts (MS or M6)| –| SNm
OPTIONAL
10| MSx2Srnrn cap head bolt| 2| SNm
11| M5x3Sm IT) cap head bolt| | SNm
NOTES
The optional bolts are only required when the riser is used in conjunction
.vith the Anemoi extensions and must be requested separately.
TOOLS REQUIRED
T25 Torx key Torque wrench
M2.5 Hex key
NOTES
The M2.5m hex does not required any torque to be applied. Finger tight vonly
is more than sufficient. WattShop Anemoi adjustable risers are universal
across numerous different riser stacks and provide you with the ability to
micro adjust your arm rest angle from 10 degrees through to 30 degrees.
If combined with our universal or inline pole clamps they’ll enable you to
angle both your arm rests and your extension poles. Furthermore the adjustable
riser is compatible with our Anemoi extension system if you decide to upgrade
to our integrated system.
The riser offers a slot to accommodate for 1S-40mm fore-aft stack centres and
mounts to a flat top riser stack, either MS or M6 and bolt down or bolt up.
For bolt up options we have supplied our custom barrel nuts (you will have
specified MS or M6).
When combined with the universal pole clamps or extension system they provide
the option of full internal cable routing.
INSTALLATION CUIDE
-
Lay all components and hardware out on a table. You may need to dismantle the adjustable riser.
-
Remove your current arm rests and any existing angled risers so the top of your extension clamp block s visible and ascertain whether your system is bolt down or bolt up. Position the lower riser (part 2) onto the top of your clamp block.
-
Bolt down using your existing bolts or bolt up from the underside of your basebar using the relevant sized barrel nuts (part 9) sat within the slot of the lower riser.
-
Position the upper riser (part I) into the lower riser. Insert the lateral grub screw (part 5), torque to lNm (do not exceed).
Set the tilt to your desired angle, initially by screwing in the central grub screw (pa rt 5) from the top of the upper riser. -
Slide the retaining nuts (parts 3 and 4), nto the lower riser. The shorter nut to the rear hole and the longer nut to the front. Install the M5x25mm bolt (part 8) to the front hole and the M5xl8mm bolt to the rear hole (part 7) with the groove in the retaining nuts aligned vertically and torque “‘ to SNm. You will need to torque the front bolt first. Ensure the anti-vibration washers (part 6) are nstalled.
-
Attach your arm rests to the upper riser using the your existing armrest bolts. The upper riser utilises 25mm bolt centres so you will need to ensure your arm rest offers this bolt spacing.
Please note when installing in conjunction with one of our pole clamps models you will receive additional hardware. Please refer to the relevant installation guide for this nformation.
If combining with our universal or inline pole clamps you will need to remove your existing extension clamp block and nstall the pole clamp (see the universal and inline pole clamp installation guides).
For installation with the Anemoi extension system please refer to the extension system installation guide.
@watt_Shop
@wattShop
@shopforwatts
[email protected]
www.shopforwatts.co.uk