BRAWA 46758 Two Axle Standard Passenger Car Instruction Manual
- June 27, 2024
- BRAWA
Table of Contents
BRAWA 46758 Two Axle Standard Passenger Car
Specifications:
- Model: Two-axle standard passenger car Pwi-28, Bi-29, BCi-28, Ci-28
- Additional Model: Two-axle command car Bif-28, BPwif-28 Scale: H0 Scale
- Recommended Power Source: Toy transformer compliant with VDE 0570-2-7/DIN EN 61558-2-7:2008-06
Product Usage Instructions
Fitting Additional Parts:
Additional parts are included for showcase purposes. Be aware that adding
these parts may limit the driving mode of the model.
Mounting the Closed Variant:
- Dismantle the open folding guard, open folding grille, and transition plate if present.
- Mount the closed version in place of the dismantled parts.
AC Wheels and Oils:
The model comes with insulated wheelsets for DC power. You can exchange them
for AC wheelsets at your BRAWA dealer. Regularly oil the wheel bearings with
fine model oil.
Couplings:
The model uses standard NEM couplings compatible with H0 gauge model railway
couplings.
Operating Instructions:
Use only a toy transformer compliant with VDE 0570-2-7/DIN EN
61558-2-7:2008-06 as the voltage source for this product.
Maintenance:
- To install a function decoder, follow the provided electrical connection plan for AC/DC operation.
- Open the roof of the model.
- Unscrew the necessary parts to access the light guide plate and function decoder installation area.
- Solder the function decoder as per the electrical connection plan.
- Place the light guide plate and function decoder in the car.
- Screw everything back together and ensure proper placement.
General information
Fitting additional parts
There is an accessory bag added to the model but may be not all parts will be
needed. The additional parts are intended for showcase. After mounting the
additional parts, there can be limitations in driving mode.
Mount the closed variant
The open folding guard (1) (not all models), the open folding grille (2)
and the transition plate (3) are fitted at the factory. These can be replaced
by the closed version.
AC wheels
This wagon is supplied with insulated wheel-sets for DC power supply. They can
be exchanged for wheel-sets for AC operation at your BRAWA dealer. You can
also order the AC wheel set separately.
Order no.: 2187 Wheel with solid centre set AC
Oils
The wheel bearings should be oiled regularly with fine model oil.
Couplings
The coupling is a standard NEM coupling, and can therefore be used with all
other standard H0-gauge model railway couplings.
- Scale and true to original small-sized model for adult collectors.
- Only a toy transformer produced compliant with VDE 0570-2-7/DIN EN 61558-2-7:2008-06 may be used as a voltage source to operate this product.
- This product conforms to the current CE standards
- Electrical equipment may not reach to domestic waste. According to the current terms of the country reference the electrical eqipment must professionally disposed of.
Accessory
Fitting LED lighting board, Order no. 2212
- Open the roof.
- Shorten the PCB to the length of the car.
- Sold the wires at the PCB as shown in the electrical connection plan AC or DC. Install and connect the power pic up shoe for AC version (Connection wire see table accessory).
- Place the PCB with LEDs downwards.
- Snap the roof in the correct position.
Maintenance
Install the function decoder
- Open the roof.
- Unscrew the screws.
- Lift off the light guide plate with solder interface (1).
- Sold the function decoder (2) as shown in the electrical connection plan AC/DC. Install and connect the power pic up shoe for AC version (Connection wire see table accessory).
- Place the light guide plate with solder interface (1) and function decoder (2) in the car.
- Screw in the screws.
- Snap the roof in the correct position.
Additional information for passenger car
All Versions
The lighting circuit board of the passenger car has a soldering interface for
the installation of a function decoder.
Assignment of the physical outputs
Additional information for passenger car/command car
Function decoder interface
When installing the decoder (FH22 for AC and DC BRAWA no .: 0021886.00, FH05B
BRAWA no.: 0019694.00 is sufficient for DC; the function decoders are optional
order parts) the track on the right (TR, red wire) and the track on the left
must be used to operate the interior lighting (TL, black wire), the function
output (AUX1, green wire) must be connected and the 0-ohm resistor R5 must be
removed. If a buffer capacitor is required for the decoder, V+ from the
decoder (V+/Dec., Pin 6, blue wire) and ground (GND, Pin 5, brown wire) must
be connected. F0_f (LV) and F0_r (LR) are only required if a red tail light
should be retrofitted. When connecting LV, R3 must be removed in digital mode,
when connecting LR, R4 must be removed. In the passenger car with an open
platform, the platform light can be switched on separately. To do this, add a
wire from the decoder to AUX2 and remove the 0-ohm resistor R6. In the baggage
car, the light in the pulpit (train driver’s compartment) can be switched on
separately. To do this, add a wire from the decoder to AUX3 and remove the
0-ohm resistor R7.
Installation option for the additional capacitors in the passenger car
Electrical connection plan AC/DC
Function decoder FH05B, only DC
With the FH05B, V + (ZVS) and GND are not provided with litz wires on the
decoder. If necessary, suitable braids can be soldered to the marked soldering
points on the back of the decoder.
All versions
The control car is equipped with a PluX22 interface in accordance with NEM
658.
Version: Basic+ (analog DC)
In analogue driving mode, the white/red light change is active and the
interior lighting in the passenger compartment is switched on. When installing
a PluX22 function decoder, the functions can be used according to the table
“Function assignment for function decoder FH22-4”. When installing a decoder,
please also note the points “Assignment of the physical outputs” and
“Digitizing the analogue Basic+ version”.
Version: Basic+ (analog AC)
In analogue driving mode, the white/red light change is active and the
interior lighting in the passenger compartment is switched on. By changing the
CV programming of the decoder, additional functions (such as the light in the
driver’s cab) can be activated for analogue operation.
Version: Basic+ (digital AC)
In digital operation, the control car is set to DCC operating mode with
address 3 ex works. In digital operation, functions F1 to F4 are available
(see table “Function assignment for function decoder FH22-4”).
Digitizing the analog Basic+ version
Mapping recommendation for the function decoder FH22 in the control car:
Attention!
The DC models of the command car must be equipped with a function decoder in
digital operation, e.g. FH22-4 (order no. 0018271.00).
Notes on the circuit board for the analog bridge plug or function decoder
Notes on the light guide plate
Spare Parts
To fit individual spare parts it is necessary to dismantle the waggon. Please be careful not to damage any components during removal as not every component is available as spare part.
- Optional erhältlich, ist nicht im Lieferumfang enthalten.
- Optional, not included
- Die DC-Modelle des Befehlswagens müssen im Digitalbetrieb zwingend mit einem Funktionsdecoder, z. B. FH22-4 (Best.-Nr. 0018271.00), ausgestattet werden.
- The DC models of the Train’s Command Car must be equipped with a function decoder, e.g. FH22-4 (Order No. 0018271.00), for digital operation.
Important information:
When ordering spare parts you must always state the order number and give the
description. If you do not do this, the order cannot be processed.
- Example of order number: Position (33), Coupler spring = 0023093.00, Coupler spring
- Ordering spare parts:www.brawa.de/en/service/spareparts We reserve the right to deviations in printing, color and structural or design modifications to the original as well as our advertising material.
The packaging and operating instructions are part of this product.
They contain important information concerning safety, use and disposal. Store
these carefully. Hand it over to third parties.
Brawa Artur Braun Modellspielwarenfabrik GmbH & Co. KG
- Uferstraße 24-30 · D-73630 Remshalden
- Hotline +49 (0)7151-979 35 68
- Telefax +49 (0)7151-746 62
- www.brawa.de
FAQ
Q: Can I use any transformer to power this model?
A: No, only a toy transformer compliant with VDE 0570-2-7/DIN EN
61558-2-7:2008-06 must be used as the voltage source.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>