Klauke EK 35 Battery Powered Hydraulic Crimping Tool Instruction Manual

June 29, 2024
Klauke

Klauke EK 35 Battery Powered Hydraulic Crimping Tool

Specifications

  • Model: EK 35/4CFB
  • Manufacturer: Klauke UK Ltd.
  • Country of Origin: Germany
  • Warranty: 2 years
  • Compatibility: For use with UL-listed wire connectors identified in the instructions provided
  • Battery Requirement: For use only with an 18 V Bosch battery series

Product Usage Instructions

Safety Guidelines

  • Before using the tool, carefully read all safety warnings, instructions, illustrations, and specifications provided in the manual.
  • Failure to follow the guidelines may result in electric shock, fire, or serious injury.
  • Keep all warnings and instructions for future reference.

General Safety Rules

Ensure to adhere to the following safety rules:

  1. Always wear appropriate personal protective equipment.
  2. Inspect the tool for any damage before use.
  3. Avoid contact with live electrical components.

Pre-Work Preparation

  1. Apply oil to the necessary parts as per DIN EN 50110 guidelines.
  2. Check the battery level and ensure it is compatible with the tool (18 V Bosch battery series).

Tool Usage

Follow these steps for using the Klauke EK 35/4CFB tool:

  1. Press the power button and hold for 20 seconds to activate the tool.
  2. Perform the desired task with the tool for up to 20 seconds.
  3. If needed, repeat the process as required.

FAQ

  • Q: How often should I have my Klauke tool checked?
  • A: It is recommended to have your Klauke tool checked yearly through an Authorized Service Center (ASC) to ensure its optimal performance and safety.
  • Q: What should I do if the warranty seal is broken?
  • A: If the warranty seal is broken, it may result in a loss of warranty. Contact the Klauke-Service Team for further assistance.

Introduction

  • Thank you for choosing a Klauke tool. We hope it gives you lots of pleasure.
  • You have purchased a quality product „Made in Germany“, which is covered by a 2-year warranty. The warranty commences from the purchase receipt date.
  • To ensure lasting enjoyment and an awless tool function, the product must be serviced by an Authorised Service Center (ASC) after 10,000 operations or after 3 years. Should the service Interval exceed 10.000 cycles the warranty claim is void.
  • The Service includes predictive maintenance in which worn-out parts will be replaced and safety-relevant parts checked/replaced.
  • We recommend to have the tools checked yearly through an Authorized Service Center (ASC).

For questions about our tool service, we are personally available at the following telephone numbers:

  • Technical Support +492332709544

  • Repairs / Loaner tools +492332709540

  • The Bluetooth® word mark and Bluetooth® symbol are registered trademarks of Bluetooth SIG, Inc., and any use by Gustav Klauke GmbH is licensed.

Overview

Dimension

WARNING

  • Read all safety warnings, instructions, illustrations and specifications provided with this power tool.
  • Failure to follow all instructions listed below may result in electric shock, fi re, and/or serious injury.
  • Save all warnings and instructions for future reference.

Use tool only with 18 V Bosch battery

All manuals are also available on www.Klauke.com

Parts

Installation Instructions

www.klauke.com/connectivity.

EK 35/4CFB

Crimp Chart EK35/4xxx series tools

Klauke R-series Copper connector type|

Ring type

|

Angle type 90°

|

Angle type 45°

---|---|---|---
Copper lugs R-series (Class 2 & 5)| 3Rxx – 10Rxx| 43Rxx – 50Rxx| 43Rxx45 – 50Rxx45
Copper slices R-series (Class 2 & 5)| | |
T-splices R-series (Class 2 & 5)| | |
Cross-Splices (Class 2 & 5)| | |
Lugs for switch gear connections (Class 2 & 5)| 5SGxx – 10SGxx| |
Klauke L-series Copper connector type|

Ring type

|

Angle type 90°

|

Angle type 45°

Copper lugs L-series (Class 2, 5 & 6)| L16xxxx – L150xxxxx| L16890xx – L150890xxx| L16845xx – L150845xxx
Copper slices L-series (Class 2, 5 & 6)| | |
Klauke NDC-series Copper connector type|

Ring type

|

Fork type

|

Pin type

Copper lugs NDC-series (Class 2 & 5)| NDC16-150| –| –
Number of crimps*:                  6 mm² – 16 mm² = 1 crimp / 25 mm² – 150 mm² = 2 crimps

Elektrowerkzeug Typ EK354CFB

CE-´* – Declaration of conformity. We declare under our sole responsibility that this product conforms with the following standards or normative documents: EN 62841-1, EN ISO 12100, EN ISO 13857, EN ISO 13854, EN 28662-1, EN 61000-6-3, EN 61000-6-2, EN 60529, EN ISO 14118 under the regulations of directives 2006/42/EG, 2014/30/EU, 2011/65/EU

CONTACT

  • Gustav Klauke GmbH
  • Auf dem Knapp 46
  • D-42855 Remscheid
  • Telefon +49 2191 907 0
  • www.klauke.com

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals