testo N8NLSD4BT-S98 Pin Wheel Anemometer User Manual
- June 27, 2024
- testo
Table of Contents
testo N8NLSD4BT-S98 Pin Wheel Anemometer
Specifications
- Product: testo 400
- Mat.-No.: 0440 4000
- Dimensions: 210 x 95 x 39 mm / 8.3 x 3.7 x 1.5 in
- Battery: Rechargeable Li-Ion (5550 mAh)
- Pressure Range: 0 … +200 hPa / 0 … +80 InH2O and +700 … +1100 hPa / +280 … +440 InH2O
Product Usage Instructions
Power On/Off
- To power on the device, press the ON button. To power off, press the OFF button.
Reset
- In case of any issues or to reset the device, press the RESET button.
LED Status
- The device features LED indicators for status updates. Refer to the user manual for specific LED indications.
Battery Charging
- Charge the device using the provided rechargeable Li-Ion battery.
- Connect the charger to a power source and the device for charging.
Wireless Module (if applicable)
- If using the wireless module, ensure compliance with regulations in the respective country of use. Refer to the user manual for wireless module setup instructions.
Additional Resources
- For detailed instructions, refer to the user manual at Product Manuals
- For software downloads and updates, visit: Software Downloads
FAQ
- Q: What should I do if the device does not power on?
- A: Ensure the battery is charged and securely connected. If the issue persists, refer to the troubleshooting section in the user manual or contact customer support.
- Q: How do I calibrate the pressure readings?
- A: Calibration instructions are provided in the user manual. Follow the outlined steps to calibrate the pressure sensors for accurate readings.
Overview
Charging
LED status
Power
Bluetooth
Info
Symbols
Information
Approvals and Certification
Product
| testo 400
---|---
Mat.-No.
| 0440 4000
Date
| 13.06.2024
The use of the wireless module is subject to the regulations and stipulations of the respective country of use, and the module may only be used in countries for which a country certification has been granted. The user and every owner should adhere to these regulations and prerequisites for use and acknowledge that the re-sale, export, import, etc. in particular in countries without wireless permits, is his responsibility.
| Country | Comments |
|---|---|
| Australia New Zealand |
Brazil|
06215-24-04701
See Brazil Information
Canada| Contains IC: 21461-LSD4BTS98
Compliance Distance: 10 mm
See IC Warning
China| CMIIT ID: 23J9939LL523
Europa + EFTA|
Hereby, Testo SE & Co. KGaA declares that the radio equipment type testo 400 – 0440 4000 complies with Directive 2014/53/EU.
The full text of the EU Declaration of Conformity is available at the following internet address: https://www.testo.com/eu- conformity
EU countries:
Belgium (BE), Bulgaria (BG), Denmark (DK), Germany (DE), Estonia (EE), Finland (FI), France (FR), Greece (GR), Ireland (IE), Italy (IT), Latvia (LV), Lithuania (LT), Luxembourg (LU), Malta (MT), Netherlands (NL), Austria (AT), Poland (PL), Portugal (PT), Romania (RO), Sweden (SE), Slovakia (SK), Slovenia (SI), Spain (ES), Czech Republic (CZ), Hungary (HU), Republic of Cyprus (CY).
EFTA countries:
Iceland, Liechtenstein, Norway, Switzerland
WEEE Reg. no. DE 75334352
Japan| Contains Lierda S98 BLE module
201-200960
See Japan information
South Africa|
Radio Equipment Type Approval Number: TA-2024/0331
South Korea|
See KCC Warning
Thailand| Authorized
Türkiye| Authorized
United Kingdom (GB)|
The UK Declaration of Conformity can be found on the testo homepage www.testo.com under the product-specific downloads.
USA|
Contains FCC ID: N8NLSD4BT-S98
See FCC Warnings
Bluetooth ® **Module| Feature**
| Values
---|---|---
Bluetooth® range| up to 60 m (196 feet) (free field
Radio type| Bluetooth® Low Energy (BLE)
Company| Lierda Science & Technology Group Co., Ltd
Lierda LSD4BT-S98B
RF Band| 2402 – 2480 MHz
Power output| 8.77 dBm
Bluetooth ® **SIG Listing| Declaration ID| D051404
Member company| Testo SE & Co. KGaA
| Comments
---|---
Hongkong| Authorized
Taiwan**|
See NCC Warning
IC Warnings
FCC STATEMENT
RSS-Gen & RSS-247 statement
This device complies with Industry Canada license-exempt RSS standard(s).
Operation is subject to the following two conditions:
- this device may not cause interference, and
- this device must accept any interference, including interference that may cause undesired operation of the device.
Caution: Radio Frequency Radiation Exposure
This equipment complies with IC radiation exposure limits set forth for an
uncontrolled environment and meets the IC radio frequency (RF) Exposure
Guidelines.
Co-Location
This transmitter must not be co-located or operated in conjunction with any
other antenna or transmitter.
FCC Warnings
Information from the FCC (Federal Communications Commission)
For your safety
Shielded cables should be used for a composite interface. This is to ensure
continued protection against radio frequency interference.
FCC warning statement
This equipment has been tested and found to comply with the limits for a Class
B digital device, according to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used under the instructions,
may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Caution
Changes or modifications not expressly approved by the party responsible for
compliance could void the user‘s authority to operate the equipment. A
shielded interface cable must be used to comply with the emission limits.
Warning
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
- this device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
Caution: Radio Frequency Radiation Exposure
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment and meets the FCC radio frequency (RF) Exposure
Guidelines.
Co-Location
This transmitter must not be co-located or operated in conjunction with any
other antenna or transmitter.
References
- Anatel — Agência Nacional de Telecomunicações
- testo.com/eu-conformity
- testo.com/manuals
- testo.com/software/datacontrol
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>