PINCUN F6 Hybrid Active Noise Cancelling Headphones User Manual

PINCUN F6 Hybrid Active Noise Cancelling Headphones

Headphone LED indicator instructions

• Power on White light stays on, then enters pairing mode.
• Pairing Mode Orange/white light alternately flashing
• Noise Cancellation Mode Active noise cancellation/Transparency mode: Green light on Noise cancellation off:
• Standby Mode Green light off.
• Low Battery State Wireless indicator light off. Red light flashes 3 times every 5 seconds.
• Charging Mode Red light on when charging, turns off when fully charged.

Headphone appearance wireframe and function introduction

Basic headphone button operations

Turning On Headphones:
Press and hold the power button ON|OFF) for 3 seconds; the white light stays on for 3 seconds, then the headphones turn on. The headphones automatically enter pairing mode after turning on, with the Wireless indicator light flashing orange/white.

Turning Off Headphones
Press and hold the power button CONIOFF) for 3 seconds; the orange light stays on for 3 seconds then turns off, and the headphones turn off.

Wireless Mode Connection
After turning on the headphones, they enter Wireless pairing mode with the indicator light flashing orange/white.  Activate Wireless on your phone and search for the device name: picun F6. Click the device name to connect, and the Wireless indicator light turns off when successfully connected.

Dual Connection Mode

1. In the powered-on state, press and hold the power button for 3 seconds to enter pairing mode, then connect to the first phone.
2. Turn off Wireless on the first connected phone, enter pairing mode on the headphones, then connect to the second phone.
3. Reconnect the headphones manually by activating Wireless on the first phone.

Automatic Shutdown and Reconnection Beyond Range
The headphones will disconnect if they go beyond the effective range. If returned within the Wireless range within 5 minutes, they will automatically reconnect; otherwise, they will shut down automatically.

Volume Adjustment
Short press the volume up + button to increase the volume Short press the volume down — button to decrease the volume.

Song Selection
Long press the volume up + button to skip to the next track. Long press the volume down —button to go back to the previous track.

Play/Pause/Answering Calls

Short press the power (ONIOFF) button to pause music during playback.
Short press the power (ONIOFF) button again to resume playback.
Short press the power (ON|OFF button to answer a call.
Short press the power (ONIOFF button during a call to hang up.
Double-tap the power CON/OFF button to reject a call.

Noise Cancellation Mode
In non-audio cable mode, short press the ANC button to activate active noise cancellation. Press again to enter Transparency mode, and press once more to turn off the noise cancellation function.
Note : Adaptive noise cancellation is only available in Wireless mode (not available when the headphones are off). In adaptive mode, the headphones emit sound to perform audio collection. Proper wearing of headphones is required during music playback.

Spatial Audio Function
In Wireless mode, short press the 3D button to enter Spatial Sound Mode (prompt: two beeps). Press the 3D button again to enter Spatial Audio Head Tracking Mode (prompt: three beeps). Press the 3D button once more to return to Normal Sound Mode (prompt: one beep). Note: The sound mode does not have a memory function; you need to adjust to the desired sound mode each time you turn on the headphones.

Head Tracking Calibration Function
In Music Playback Mode, there are two ways to calibrate the audio’s central positioning point.

1. Press the play/pause button on the headphones to pause the music, then play again for the spatial sound to be centered.
2. The spatial sound will automatically calibrate and center itself if you maintain one direction for 10 seconds.

Low Latency Feature
In any power-on mode, triple-click the ANC button to enter low latency mode, and the headphones will indicate this with two “dong-dong” sounds. Triple- click again to exit low latency mode, indicated by a single “dong-dong” sound.

Voice Assistant Function
In non-call status, triple-click the power button to activate the voice assistant feature.

Chinese-English Voice Switch
In pairing mode, double-click the volume up button to enter the voice switching function.

Battery Capacity Status
When the headphones are connected to an iOS device, the current battery status of the headphones is displayed in the top right corner of the iOS device screen.

Charging the Headphones
When the battery is low, please charge with a USB charging cable for about 3 hours. Headphones Automatically Turn Off During Charging. During charging, the red indicator light stays on and turns off when fully charged.

Clearing Pairing Information
In non-call status, long-press both the volume up (+) and volume down (-) buttons for 3 seconds.

Line-in Mode
Insert an audio cable, and the headphones will automatically power off.

Note : Wireless and noise cancellation functions cannot be used in Line in mode. To use Wireless, remove the audio cable and power on the headphones again.

Headphone parameter accessories

• Wireless protocol  A2DP/AVRCP/HFP/HSP
• Receiving distance  10m
• Speaker size  40mm
• Frequency range  20HZ-20kHZ
• Speaker sensitivity   114÷3dB
• Speaker impedance  32Ω÷15%
• Microphone sensitivity  42dB‡1dB
• Working current  13-45mA
• Charging Voltage  5V

Packaging accessories

1. Wireless headphones
2. Charging cable
3. Audio cable
4. User’s manual

Important Tips

1. Please use a 5V-1A/5V-2A charger to charge the charging case. Using a charger with a higher voltage may damage the charging case.
2. If the headphones are not used for more than 3 months, please charge them before use.
3. For long periods of non-use, it is recommended to charge the headphones once every 3 months to effectively protect the battery’s lifespan.
4. Upon receiving the headphones, please fully charge them before using.

Cautions

• Avoid placing the headphones in high-temperature environments, including direct sunlight.
• Do not place the headphones near open flames or other excessively hot environments.
• Keep the headphones dry and avoid exposing them to damp environments or submerging them in liquids.
• Only use the provided charging cable to charge the headphones; do not attempt to charge them using other methods.
• Do not disassemble the headphones, and refrain from attempting to repair or modify them in any way.
• Be cautious of excessive dropping, impact, scratching, or any behavior that may affect the functionality of the headphones. If any damage occurs, such as dents, punctures, tears, deformations, or corrosion, please stop using the headphones immediately and contact the seller or reach out to us through the contact information provided on the warranty card.
• If the headphones emit an unusual smell, become excessively hot, or show abnormal changes in color or shape, please stop using them immediately and contact the seller or reach out to us through the contact information provided on the warranty card.

Warning
Prolonged use of headphones at high volumes may cause hearing damage. Please use them responsibly and at moderate volume levels.

Warranty instructions

Please keep the warranty card and valid proof of purchase to present when the product fails to repair, if you cannot provide the warranty card or relevant proof of purchase, the product warranty period will be calculated based on date of delivery of the product.

Warranty provisions

1. Advisory services, users can call 4008894883 for any problems encountered in the warranty process.
2. Within one year from the date of purchase, if the quality of the product fails and the technical staff of the company confirms that the failure of the machine occurs under normal use, free warranty service will be provided.
3. The Company shall refuse to provide free warranty service and shall only provide repair service free of labor charges and only charge for parts in the following cases.
4. The product has been damaged by misuse, negligent use or force majeure;
5. The product has been dismantled or repaired without the company’s authorization.
6. Crushing, water immersion, shell damage, deformation and other man-made damage.
7. The original warranty card and the sales certificate of the sales unit cannot be provided, and the date of purchase is beyond the warranty period.
8. The free service provided by this warranty card does not include accessories, other decorations, gifts, etc.

Product Qualification Certificate
After inspection,the product meets the technical standards and is allowed to leave the factory

FCC Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

To assure continued compliance, any changes or modifications not expressly approved by the party.
Responsible for compliance could void the user’s authority to operate this equipment. (Example- use only shielded interface cables when connecting to computer or peripheral devices).

This equipment complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation.

RF warning statement
The device has been evaluated to meet general RF exposure requirement.
The device can be used in portable exposure condition without restriction.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>