Foneric FM6884 Bluetooth Wireless Audio Adapter User Manual

Foneric FM6884 Bluetooth Wireless Audio Adapter

PRODUCT OVERVIEW

First, select the TX or RX mode

TX mode 1 : Connect Mater low to a heaciphone jack.

The TX mode is for audio transmission from a wired headphone jack (eg. aircraft, TV or treadmil in gym) to AirPods or wireless headphones

TX mode 2 Connect MateF low to the USB port of a PC through a USB cable.

The TX mode is for audio transmission from a PC to AirPods or wireless headphones.

RX mode : Connect Materlow to the AUX-IN intertace of another device

The RX mode is for Bluetooth audio reception from other devices (such as mobile phones or tablets) and transmission to AUX-IN ports (such as in the car, ship) of connected stereo devices.

TX mode – AUX

1. Set MateFlow to the TX mode.

2. Press and hold the ON/OFF button for 3 seconds to turn on the MateFlow. Do not release it until the indicator flashes green twice.

3. The indicator of MateFlow will flash red and green alternately in about 15 seconds, indicating that MateFlow is in the pairing made (MateFlow is being connected in the first 15 seconds).
   If the indicator does not flash red and green alternately, press the Reset button to restore default settings.

4. (1) Pairing between MateFlow and AirPods: Before enabling the pairing mode of AirPods, put AirPods into the charging case. Open the lid, and press and hold the button on the back of the charging case until the indicator flashes white.
   After they are connected successfully, the indicator on the charging case will turn green. The indicator of MateF low will be green for 10 consecutive seconds (indicating that Mateflow is in the working status)  (2) Pairing between MateF low and other wireless headphones: enable the  Bluetooth pairing mode of your headphones (refer to the user manual of the headphone for more details). After they are connected successfully, the indicator of MateFlow will be green for 10 consecutive seconds, indicating that MateFlow is in the working status. * It may take 90 seconds for initial pairing. But your AirPods will be saved in MateFlow for later connection.

5. Pairing between MateFlow and another headphone: (1) Directly disconnect the headphone A (the indicator of MateFlow will flash green twice in 5 seconds, indicating that the headphone is disconnected). To connect the headphone B, double-click the ON/OFF button (the indicator of MateFlow will flash red and green alternately, indicating the pairing mode) to find and pair the headphone B, (2) Double-click the ON/OFF button. MateFlow will be in the pairing mode, until the headphone B is found and paired successfully.

6. After pairing and activating one headphone, you can pair another headphone with MateFlow. Double-click the side button to enable the pairing mode (if the headphones are successfully connected, the indicator of MateFlow will be green for 10 consecutive seconds).

7. If MateFlow is turned off and then turned on again, it is being connected in the first 15 seconds to the last connected device before shutdown. If they are not connected successfully in 15 seconds, the indicator of MateF low will flash red and green alternately, indicating the pairing mode. Double-click the ON/OFF button for pairing with other devices.

8. 8. Pairing timeout:

   • (1) If its start time is 5 minutes or less, Matef low will be in the pairing mode, until it is paired successfully with a headphone.
   • (2) If its start time is more than 5 minutes, MateFlow will not be paired successfully with any headphones. In this case, MateFlow will be automatically shut down due to timeout. 9. Shutdown: press and hold the ON/OFF button of MateFlow for 3 seconds. The indicator of MateFlow will flash red five times (300ms/time).

9. Shutdown: press and hold the ON/OFF button of MateFlow for 3 seconds. The indicator of MateF low will flash red five times (300ms/time).

USB

TX mode – USB

1. Set MateFlow to the TX mode.

2. Connect MateFlow to a PC through a USB cable (give priority to the USB port on the back of PC).

3. The indicator of MateFlow will flash red and green alternately in about 15 seconds, indicating the pairing mode (MateF low is being connected in the first 15 seconds). If the indicator does not flash red and green alternately, press the Reset button to restore default settings.

4. (1) Paining between MateFlow and AirPods: Before enabling the pairing mode of AirPods, put AirPods into the charging case. Open the lid, and press and hold the button on the back of the charging case until the indicator flashes white.After they are connected successfully, the indicator on the charging case will turn green. The indicator of Matef low will be green for 10 consecutive seconds (indicating that MateFlow is in the working status).
   (2) Painting between MateF low and other wireless headphones: enable the Bluetooth pairing mode of your headphones (refer to the user manual of the headphones for more details). After they are connected successfully, the indicator of MateFlow will be green for 10 consecutive seconds, indicating that MateFlow is in the working status. It may take 90 seconds for initial pairing. But your AirPods will be saved in MateFlow for later connection.

5. Pairing between MateF low and another headphone:
   (1) Directly disconnect the headphone A (the indicator of MateFlow will flash green twice in 5 seconds, indicating that the headphone is disconnected). To connect headphone B, double-click the ON/OFF button (the indicator of MateFlow will flash red and green alternately, indicating the pairing mode to find and pair headphone B.
   (2) Double-click the ON/OFF button. MateFlow will be in the pairing mode until the headphone B is found and paired successfully:

6. Pairing between Matef low and two headphones at the same time:
   After paining and activating one headphone, you can pair another headphone with MateFlow.
   Double-click the side button to enable the pairing mode (if the headphones are successfully connected, the indicator of MateFlow will be green for 10 consecutive seconds).

7. If MateFlow is turned off and then turned on again, it is being connected in the first 15 seconds to the last connected device before shutdown. If they are not connected successfully 15 seconds, the indicator of MateFlow will flash red and green alternately, indicating the pairin mode. Double-click the ON/OFF button for pairing with other devices.

8. Pairing timeout: (1) If its start time is 5 minutes or less, MateFlow will be in the pairing mode, until it is paired successfully with a headphone (2) If its start time is more than 5 minutes, MateFlow will not be paired successfully with any headphone. In this case, MateFlow will be automatically shut down due to timeout.

9. Shutdown: press and hold the ON/OFF button of MateFlow for 3 seconds. The indicator of MateF low will flash red five times (300ms/time).

TX mode – USB

1. Set MateFlow to the TX mode.
2. Connect MateFlow to a PC through a USB cable (give priority to the USB port on the back of PC).
3. The indicator of MateFlow will flash red and green alternately in about 15 seconds, indicating the pairing mode (Matef low is being connected in the first 15 seconds). If the indicator does not flash red and green alternately, press the Reset button to restore default settings.
4. (1) Painting between MateFlow and AirPods: Before enabling the pairing mode of AirPods, put AirPods into the charging case. Open the lid, and press and hold the button on the back of the charging case until the indicator flashes white. After they are connected successfully, the indicator on the charging case will turn green. The indicator of Matef low will be green for 10 consecutive seconds (indicating that Mateflow is in the working status). (2) Pairing between MateFlow and other wireless headphones: enable the Bluetooth pairing mode of your headphones (refer to the user manual of the headphones for more details). After they are connected successfully, the indicator of MateFlow will be green for 10 consecutive seconds, indicating that MateFlow is in the working status. * It may take 90 seconds for initial pairing. But your AirPods will be saved in MateFlow for later connection.
5. Pairing between Matef low and another headphone: (1) Directly disconnect the headphone A (the indicator of MateFlow will flash green twice in 5 seconds, indicating that the headphone is disconnected). To connect the headphone B, double-click the ON/OFF button (the indicator of MateFlow will flash red and green alternately, indicating the pairing mode) to find and pair headphone B. (2) Double-click the ON/OFF button. MateFlow will be in the pairing mode until the headphone B is found and paired successfully.
6. Pairing between Matef low and two headphones at the same time: After painting and activating one headphone, you can pair another headphone with MateFlow. Double-click the side button to enable the pairing mode (if the headphones are successfully connected, the indicator of MateFlow will be green for 10 consecutive seconds).
7. If MateFlow is turned off and then turned on again, it is being connected in the first 15 seconds to the last connected device before shutdown. If they are not connected successfully in 15 seconds, the indicator of MateF low will flash red and green alternately, indicating the pairing mode. Double-click the ON/OFF button for pairing with other devices.
8. Paining timeout: (1) If its start time is 5 minutes or less, MateF low will be in the pairing mode, until it is paired successfully with a headphone. (2) if its start time is more than 5 minutes, MateFlow will not be paired successfully with any headphones. In this case, MateFlow will be automatically shut down due to timeout.
9. Shutdown: press and hold the ON/OFF button of MateFlow for 3 seconds. The indicator of MateF low will flash red five times (300ms/time).

RX mode

Use MateFlow through the AUX-IN port.

1. Set MateF low to the RX mode.

2. Press and hold the ON/OFF button for 3 seconds to turn on MateFlow. Do not release it until the indicator flashes green twice.

3. The indicator of MateFlow will flash red and green alternately in about 15 seconds, indicating that MateF low is in the pairing mode (MateFlow is being connected in the first 15 seconds). If the indicator does not flash red and green alternately, press the Reset button to restore default settings.

4. Enable the pairing mode of MateF low and Bluetooth Settings mode of your mobile phone. Select MateF low from “Other Devices” for pairing. The indicator of MateFlow will be green for 10 consecutive seconds, indicating that MateFlow is in the working status.

5. Once your mobile phone is successfully connected, connect MateFlow to the aux-in port of the desired source.

6. Pairing of MateFlow and another mobile phone: (1) Double-click the ON/OFF button to disconnect the currently paired mobile phone A (MateFlow will have a prompt tone: disconnect, and its indicator will flash green twice in 5 seconds, indicating that the mobile phone A is disconnected). To connect the mobile phone B, double-click the ON/OFF button (the indicator of MateFlow will flash red and green alternately, indicating the pairing mode). Open the Settings of the mobile phone B, and find and pair MateFlow through Bluetooth. (2) Double-click the ON/OFF button. MateF low will be in the pairing mode. Open the Settings of the mobile phone B, and find and pair MateFlow through Bluetooth.

7. If MateFlow is turned off and then turned on again, it is being connected in the first 15 seconds to the last connected device before shutdown. If they are not connected successfully in 15 seconds, the indicator of MateFlow will flash red and green alternately, indicating the pairing mode. Double-click the ON/OFF button for pairing with other devices. You can find MateFlow in “Other Devices” of the Bluetooth list of your mobile phone.
   Note: If a device has been connected to MateFlow, directly click MateFlow in its connection history of the Bluetooth list.

8. Pairing timeout:

   • (1) If its start time is 5 minutes or less, MateFlow will be in the pairing mode, until it is paired successfully with a mobile phone.
   • (2) If its start time is more than 5 minutes, MateFlow will not be paired successfully with any mobile phone. In this case, MateFlow will be automatically shut down due to timeout.

9. Shutdown: press and hold the ON/OFF button of Mateflow for 3 seconds. The indicator of MateF low will flash red five times (300ms/time).

Charging of MateFlow

Charge MateFlow by inserting one end of the accompanying USB-C to USB-A cable into MateF low and the other end into a powered USB port. MateFlow can be fully charged in 4 hours.

Fully charged battery of MateF low:

12 consecutive hours in the TX mode (60% volume) 27 consecutive hours in the RX mode (60% volume) It is recommended to fully charge MateFlow before using it for the first time. In case of insufficient powder, the indicator of MateFlow will flash red at intervals of 2 seconds, reminding you to charge MateF low.

In the charging process, the indicator of MateFlow will be constantly red. After MateFlow is fully charged, its indicator will flash green twice and then light off.

Once MateFlow is connected to a powered USB port, it will be turned on, regardless of its mode (TX/RX).*

FCC Compliance Statement

This device complies with Part 15 of the FCC Rules. Operation needs to meet the following two conditions:

1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired operation.

WARNING: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

NOTE: This device has been tested and meets standard requirements. Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or telecommunications, which can be corrected by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Adjust the direction or position of the receiving antenna,
• Increase the distance between the equipment and the receiver,
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult your dealer or an experienced radio/TV technician for assistance.

Disposal of electronic equipment

This electronic device should not be disposed of with ordinary household waste Dispose of this device at an approved facility or your local recycling center. Please comply with current rules and regulations when disposing of equipment.

If you have questions, please contact your local council.

Declaration of conformity

Hereby the manufacturer declares that this product complies with the essential requirements and applicable regulations of the Radio Equipment Directive 2014/53/EU, EMC Directive 2014/30/EU. The full declaration of conformity can be found:  https://itronicsmall.com/eu-declaration-of-conformity/complies

Use of the ON/OFF button:

Press and hold it for 3 seconds: power-on/off

Double-click it re-pairing

Use of the side button:

Press and hold it for 4 seconds: clear all TX/RX pairing information
Press it once: get battery power information
Press it twice : pair and connect another headphone

Indicator:

Flashing green twice = power-on

Constantly green for 10 seconds = working status

Flashing red five times (300ms/time) = power-off

Flashing red and green alternately = pairing mode

Flashing green/red twice at intervals of 5 seconds = device disconnection

Flashing red at intervals of 2 seconds = low power

Charging = constantly red

End of charging (type-c connection) = flashing green twice and then off

Customer Service

• Email: support@palavue.com
• Hours: 7 Days 24 Hours

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>