NOVA LIFE 54643-060-71 Interior Pendant Instruction Manual

Instruction Manual
For ORBIT
INTERIOR PENDANT
Art Nr. 54643-060-71

**Pre-Installation

**

PLANNING THE INSTALLATION
Read all instructions before assembly and installation. Before starting installation of the fixture or removal of a previous fixture, disconnect the power by turning off the circuit breaker or by removing the fuse at the fuse box. To avoid damaging this product, assemble it on a soft, non-abrasive surface such as carpet or cardboard.
TOOLS REQUIRED

Installation (Make sure to turn off the main power)

Key function of remote control

Key instructions
Turn on: Short time lamp lighting, Electricity within 5 s,
Long press for the code function, After power on 5 s Long press has no effect;
Turn off: Short time lamp goes out, Electricity within 5s
Long press for clear code function, After power on 5 s
Long press has no effect;
Cold light +

1. Short on time, Turn the cold light fixture on one level, At the same time, the warm light lamp darkens one level There are 15 levels of cold light from out to full light;
2. Long time, The luminaire is gradually lightened, At the same time, the warm light gradually darkens;

Warm light +

1. Short on time, The warm light fixture should be one step brighter, When the cold light lamp darkens one level, There are 15 levels of warm light from out to full light;
2. Long time, The warm luminaire is gradually lightened, At the same time, the cold light gradually darkened;

brightness +

1. Short on time,Heat and cold light lamps are brighter,There are 11 levels of brightness from lowest to highest;
2. Long time,The warm luminaire is gradually lightened,At the same time,the cold light gradually darkened;

brightness –

1. Short on time, Dim the light and cold lamps, There are 11 levels of brightness from highest to lowest;
2. Long time, The cold and warm light lamps are gradually dimmed; cycle: Short press the loop key,
   The light is Warm, neutral, cold, Nightlight, Four state cycles, Press short to change the state one at a time;
   night lamp: Short press the nightlight button, The lowest brightness of a lamp converted to Warm light

The key light: Key indicator light, The indicator button is pressed;
Note: One of the heating and cooling light Settings, Customers can define themselves according to the power supply and lamps

Functional specifications
Mapping function
Turn off THE LED’s AC power for more than 10 seconds, Then turn on the LED AC power again. 4 seconds, Long press the light button once, LED light flashes slowly once, The code successfully.Then the remote control can control the brightness, cooling and heating of the LED lights with good code.
Note: An LED light is only controlled by the last successful remote control. For example,lf an LED light fixture.There is a new remote control and its code matching is successful, Then the remote control will automatically clear the code with the lamp But a remote control can be coded and controlled with multiple LED lights.
Code clearing function
Turn off THE LED’s AC power for more than 10 seconds,Then turn on the LED AC power again,4 seconds,Long press the Trun off button or nightlinght button once,LED light slow flash 2 time,The Ming and Qing dynasties were successful.
Note: The function of code clearing is based on the code matching between the remote control and the lamp.For example in the following cases, the remote control and the lamp do not have the function of code clearing, If there is no clear code function A long press to turn off the light has no effect.

1. The remote control is not coded with the lamp, Then there is no clear code function,
2. When they had finished coding, they cleared the code,Then there is no clear code function
3. They have coded each other, But then came a new remote control that corresponded with the light fixture,Then the remote control and its code function will automatically clear,No dear code function,

1.On switch function.
The lamp is normally energized,Power on the 0.5S-2S switch,The light is Warm,neutral,cold,Nightlight,4 state loop switches.
2.Power off memory function
Use the remote control to adjust the brightness of LED lights, The brightness of LED lamps and the code value of the remote control will be kept in the memory of LED controller after 15S of power, Power back on after you have lost power and light the lamp at its previous brightness,And has the code remote control is still controllable

Package Contents

(Parts are not to Scale)

Light source
Max. LED 27W 1170Lumen 3000K (Dimmable)

Care and Cleaning

EXTERIOR MAINTENANCE

1. To clean the outside of the fixture, use a dry or slightly dampened clean cloth (use clean water, never a solvent) to wipe the surface of the fixture.
2. Do not use any cleaners with chemicals, solvents or harsh abrasives. Use only a dry soft cloth to dust or wipe carefully.

www.lampehust.com

Documents / Resources

| NOVA LIFE 54643-060-71 Interior Pendant [pdf] Instruction Manual
54643-060-71 Interior Pendant, 54643-060-71, Interior Pendant, Pendant
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>