LG Electronics TM15FNNAHD0 Telematics Module User Manual
- June 24, 2024
- LG Electronics
Table of Contents
LG Electronics TM15FNNAHD0 Telematics Module
TM15FNNAHD0 as telematics module device equipped in the vehicles. In charge of wireless communications in LTE/5G NR network Platform for Telematics Virtual Machine (VM) and other VMs based on Hypervisor TM15FNNAHD0 supports LTE B2/4(66)/5/7/12(17), 5G NR n2/5/66/77 network Them some use case to demonstrate LTE/5G NR performances targeted.
- High throughput features
- Low Latency features. below is just for example.
High throughput features
Demonstrate high throughput, high quality image by hotspot.
Low latency features
Images and file uploaded from the car are displayed without delay to other devices.
Frequency Band
Item| Uplink| Downlink| FDD-LTE| NR
B2(n2)| 1850~1910| 1930~1990| V| V
B4/66(n66)| 1710~1755| 2100~2155| V| V
B5(n5)| 824~849| 869~894| V| V
B12/17| 669~716| 729~746| V|
B7| 2500~2570| 2620~2690| V|
n77| 3300~4200| | V
Notice
Telematics NAD Module installation guide and information
NAD Module as TM15FNNAHD0 Module is mounted with solder ball on the main TSU board. The strength of the RF field produced by the wireless module or modules embedded in the TSU is well within all international RF exposure limits known at this time. Because the wireless modules embedded in the TSU emit less than the maximum amount of energy permitted in radio frequency safety standards and recommendations, the manufacturer believes these modules are safe for use. Regardless of the power levels, care should be taken to minimize human contact during normal operation. This module should be remain more than 20 cm (8 inches) from the body when wireless devices are on and transmitting.
This transmitter must not be collocated or operated in conjunction with any other antenna or transmitter. Operation is subject to the following two conditions: (1) this module does not cause interference, (2) this module accepts any interference that may cause undesired operation.
Information for the integrator
The integrator must not provide information to the end user regarding how to
install or remove this RF module in the user manual of the end product. The
user manual that is provided by the integrator for end users must include the
following information in a prominent location. To comply with FCC RF and IC
RSS 102 exposure requirements, the antenna used for this transmitter must be
installed to provide a separation distance of at least 20cm from all persons
and must not be collocated or operated in conjunction with any other antenna
or transmitter. The label for the end product must include FCC ID: BEJTM 15F
NNAHD0 or ARF transmitter inside, IC: 2703H TM 15F NNAHD0.
This module complies with FCC/IC rules. FCC: Part 22, Part 24, Part 27 ISED:
RSS 130, RSS 132, RSS 133, RSS 139
Furthermore, this device complies with FCC radiation exposure limits set forth
for uncontrolled environments. This module must be installed and operated with
minimum distance of 20cm between the radiating element and the user. This
module must not be colocated with any other transmitters or antennas. To
comply with FCC regulations limiting both the maximum RF output power and
human exposure to RF radiation, the maximum antenna gain including cable loss
in a mobile only exposure condition must not exceed the values listed in the
following table.
To satisfy the FCC’s exterior labeling requirements, the following text must
appear on the exterior of the end product. Contains transmitter module FCC ID:
BEJTM 15F NNAHD0 Contains transmitter module IC: 2703H TM15FNNAHD0 Changes or
modifications to this equipment may cause harmful interference unless the
modifications are expressly approved in the instruction manual. Users may lose
the authority to operate this equipment if an unauthorized change or
codification is made.
Note : If this module is intended for use in a portable device,
additional testing will be required to satisfy the RF exposure and SAR
requirements of FCC Part 2.1093 and RSS 102.
FCC Statement
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation . This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help
- FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation
Manufacturers integrating the Radio Module into other devices should note the following: The device is compliant with part 15.247 and 15.407 of Title 47 of the FCC rules. If the Link Module is integrated into a new host product, the final host product still requires Part 15 Subpart B compliance testing with the modular transmitter installed
- Label and Compliance Information
- The final end product must be labeled in a visible area with the following: “Contains FCC ID: BEJTM15FNNAHD0“ Contains IC: 2703H TM15FNNAHD0
- The grantee’s FCC ID can be used only when all FCC/ IC compliance requirements are met.
RF exposure
The module will install into mobile device such as Sound Bar This equipment
complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum
distance 20cm between the radiator & your body.
Information on test modes and additional testing requirements
- OEM integrator is still responsible for testing their end product for any additional compliance requirements required with this module installed (for example, digital device emissions, PC peripheral requirements, additional transmitter in the host, etc.).
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>