arpha K06 Wireless Home Security IP Camera User Guide
- June 24, 2024
- arpha
Table of Contents
arpha K06 Wireless Home Security IP Camera
Specifications
- Dimensions: 90(L) x 130(W)mm
- Weight: 128g
Product Information
WIRELESS HOME SECURITY CAMERA
Unlocking the Future of Security
Model: K06
Product Usage Instructions
What’s Included
- Camera quantity and accessories vary by bundle package.
- arphaCam
- Type-C Charging Cable
- Wall Mount
- Battery
- Mounting Screws and Anchors
- Quick Setup Guide
Disassembling and Assembling Battery:
- Rotate the knob 90 degrees in the direction of the arrow.
- Open the battery cover following the indicated direction.
- Insert the battery into the camera and close the battery cover.
Product Overview
Diagram
Status and Indicator
Setting Up the System
Download the App and Set up the System:
- Fully charge the battery before first-time use.
- Download the arpha app from the App Store or Google Play store.
- Register an account and connect to your wireless router (2.4GHz channel for dual-band routers).
Mounting the Camera
Mounting Instructions:
Charge arpha Camera
Charging Instructions
- Use a 5V USB Charger.
- Install arphacam 7-10 ft (2-3 m) above the ground for optimal motion sensor detection.
Disclaimer
The contents in this manual, product specifications, size, and shape are
subject to change without prior notice. The manufacturer reserves the right to
revise this manual without obligation to notify any person.
FAQ
-
Q: How do I reset the camera?
A: Long press the Reset button for 5 seconds. -
Q: What should I do if the WiFi connection fails?
A: Check your network settings and try again. If issues persist, contact customer support. -
Q: Can I install the camera outdoors?
A: The camera can be installed outdoors but avoid direct sunlight exposure for optimal performance.
WIRELESS HOME SECURITY CAMERA
Unlocking the
Future of Security
GETTING STARTED
What’s Included
Camera quantity and accessories vary by bundle package.
Disassembling and assembling battery
- Rotate the knob 90 degrees in the direction of the arrow.
- Open the battery cover as this direction below
- Insert the battery into the camera and close the battery cover
PRODUCT OVERVIEW
Diagram
- Lens
- Status LED
- Motion sensor
- Microphone
- Light
- Mounting hole
- Solar energy
- Reset button
- Charging port
- Power ON/OFF
- TF card slot
- Speaker
- Battery cover
- knob
Status and Indicator
| Device Status | Button | Indicator Light | Voice |
|---|---|---|---|
| Power On | Long press the power button for 2 seconds | Red light slow blinking |
Sound of camera start
Power Off| Long press the power button for 5 seconds| Lights All Off| Sound of
camera shutdown
Reset| Long press the Reset button for 5 seconds| Red light slow blinking|
Restore factory settings
Upgrade| /| Orange light slow blinking| The system is being upgraded, please
wait a moment
Connect the WiFi successful| /| Green light stays on| Connect the WiFi
successful
Connect the WiFi failed| /| Red light slow blinking| Connect the WiFi failed
Battery Charging| /| Red light stays on| /
Battery Charged| /| Lights All Off| /
SETTING UP THE SYSTEM
Download the App and Set up the System
-
Please fully charge the battery before using it for the first time.
-
Download the arpha app from the App Store ( iOS devices ) or Google Play store (Android devices).
-
Register an account if this is the first using the App. -
Make sure that your smartphone is connected to your wireless router ( It has to be on the 2.4GHz channel if you have a dual-band router )
Fuwei Global Co, Ltd. arpha.com -
Launch the arpha app, click “Add Device” , then select “ Camera & Lock”, and follow the screenshot below.
-
Make sure the Red indicator on the device is blinking, then press “Next Step”.
(If the operation failed, press the reset button for over 5 seconds) -
Enter your“Wi-Fi network and password” click,“Next”.
-
When the indicator light on the device turns from ashing red light to steady green light, the network configuration is complete.
MOUNTING THE CAMERA
Mount the camera
-
Firmly secure the base onto the wall using screws(depends onactual wall mount) supplied in the package. “Keep the installation angle of solar panels about 30~45°with the horizontal plane as shown in the picture below.
Take care to install the solar panel in camera so that the sun is not blocked by any items such as eaves,trees branches,etc.
-
It is suggested to install arphacam 7-10 ft (2-3 m) above the ground.
This height maximizes the detection range of the motion sensor ofarphacam. Avoid placing arphacam under direct sunlight.
CHARGE ARPHA CAMERA
DISCLAIMER
The contents in this manual, product specifications, size, and shape are
subject to change without prior notice. The manufacturer makes no
representations or warranties concerning the contents hereof and reserves the
right to revise this manual without obligation to notify any person. The
manufacturer shall not be liable for any technical or editorial errors or
omissions contained in this manual, or for any damage, direct or indirect,
from discrepancies between the manual and the product it describes. The
manufacturer assumes no responsibility, directly or indirectly, for financial
losses or claims from third persons resulting from the use of this product and
any of its functions. The total accessible capacity varies depending on the
operating environ ment. All references to speed are for comparison purposes
only. Actual data throughput may vary.
FCC Warning
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
Any Changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC RF exposure statement
The equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance between 20cm the radiator your body.