arpha AL302 Keyless Entry Door Lock Instruction Manual

arpha AL302 Keyless Entry Door Lock Instruction Manual

Installation Overview

NOTE: Screw Mounting Post (L) into holes on Mounting P;ate (C)

Preparing Door

Install Enclosed Latch and Strike Plate

NOTE: Do not extend Cylindrical Cover past 2-3/4″ (70mm)

TO CONVERT FROM 2-3/8″ (60mm) BACKSET TO 2-3/4″ (70mm) BACKSET

1. Hold latch with numbers facing forward and thumb pressing on the bolt.
2. Rotate the cylinder cover clockwise.
3. Pull and twist the extension plate all the way out.
4. Rotate the cylinder counter clockwise so that the marking aligns with the 2-3/4″ position indicator.

Install Exterior Assembly

Check that the Rubber Gasket is secured on the Exterior Assembly. Insert the Exterior Assembly onto the door with the tailpiece going through the Deadbolt Latch Set in the VERTICAL POSITION. Route the Control Wire through the door under the Deadbolt Latch Set.

Install Interior Assembly

NOTE: Make sure the Knob is in the correct position. Be careful not to pinch the control wire when assembling.

Lock and unlock using the Knob make sure the lath is opening and closing easily. If not go back to step 2 and ensure you followed the step.

Install Batteries and Cover

This Electronic lock requires (4) High Quality AA Alkaline batteries. When all 4 batteries are installed in the correct position, you should hear 2 beeps and the keypad will illuminate.

The Lock motor will engage and do a series of locking and unlocking motions in order to automatically determine your door ‘Handing” (left or right handed door).
When completed the lock will beep and the keypad will flash.

NOTE: Do not touch the Keypad until the light turns off. Do not use rechargeable batteries or non-alkaline batteries.

Testing Operation

Programming Instructions

Press any button to wake up the keypad firstly before inputing related codes.

Download the App

Download ARPHA App from the App Store (iOS devices) or Google Play (Android devices)

Sign up the Account

Create your account and follow the set up instructions in the ARPHA app.

Add the device to your app

Automatically add the device path: “Add Device” -> “Auto Scan”

Manually add the device path: “Add device” -> “Security & Video” -> Lock (BLE) -> “Next”

App Setting

Lock Management

Additional Programming Functions

Programming Symbols

Lock / Clear
Unlock/ Programming
Administrator Code

Automatic Lock Function

SET OR CANCEL AUTO LOCK
You can set the lock to automatically close after each time the lock is opened. Time value range = 5 – 900 seconds, enter the following:
Set Auto Lock:
Hear 1 beep and Light Indicator illuminates green.
To cancel Auto Lock set the time to 00, enter the following:
Cancel Time Value Auto Lock:
Hear 1 beep and Light Indicator illuminates green.

TEMPORARILY DISABLE
While in Auto-Lock mode, unlock door using , within 10 seconds you must turn the locking knob by hand to the locked position, wait more than 2 seconds then turn the locking knob back to the unlock position. The Auto-Lock mode is now disabled.

RESTORE:
To restore the Auto-Lock function, turn the locking knob by hand to the locked position, wait more than 2 seconds or press the Lock button on the keypad.

Vacation Mode

With Vacation Mode enabled, the system enters into low-power consumption mode. During this mode, all buttons and functions will be disabled until they are re-enabled.

ENABLE:

Once the door is locked then vacation mode will be engaged and all buttons and functions will be disabled

DISABLE:
To disable the Vacation Mode, you must press and hold for more than 3 seconds, then input followed by to unlock the door. Vacation Mode is now disabled.

NOTE: If you only press the for more than 3 seconds but do not input , the system will remain in Vacation Mode.

Secure Lock-out period

Warning sounds and LED flashes red after 4 incorrect code attempts: Keypad shuts down for 60 seconds.

SOUND ON AND OFF

You can “mute” or turn the “sound on” on your lock by entering the following.
(Factory setting is sound on).

1 -Sound Off
2 =Sound On
Sound Off (1)- Light Indicator illuminates green.
Sound On (2) – Hear 1 beep and Light Indicator illuminates green.

Restore Factory Settings

To reset the lock to the original factory settings including the Programming Code and all User Codes follow these steps:

1. Remove one battery for 10 seconds.
2. Reinsert the battery and wait for a long and short beep
3. Press 3 times within 3 seconds.
4. The lock will beep and the light indicator will turn green.

Low Battery Warning

Beeps and LED flashes red 7 times. Replace with good quality alkaline batteries.
Note: Removing batteries does not erase active Administrator or User Codes.

Consumer Friendly Message Guide

attempt
Power on:| 1 long beep with red lingt on, 1 short beep with green light on. After direction detection, 1 long beep with red+green light on.
Chip Reset:| 1 long beep and 1 short beep and LED illuminates green (may occur several times or once in a while)
Lock Error| 3 long beeps LED flashes red three times
Repeat operation after Lock Error| 2 short beeps three times LED flashes red six times

Customer Service

We offer one year warranty and life-time technical support to our customers.
Any confusion, please feel free to contact us at support@arpha.com

Emergency Power Supply

Insert a micro USB cable into the USB C port and use a portable battery to power the Keypad Lock.

Notice

FCC Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Warnings: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’ s authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
4. Consult the dealer or an experienced radio/TV technician for help.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>