ANKER A7850 Wireless Vertical Ergonomic Mouse User Guide

QUICK START GUIDE

Wireless Vertical Ergonomic Mouse

At a Glance

1. Scroll Wheel
2. Left Button
3. Right Button
4. DPI Switch
5. Next Page Button (Not for Apple Mac OS)
6. Previous Page Button (Not for Apple Mac OS)
7. Nano Receiver

1. DPI Switch: Press this button to switch between 800, 1200, and 1600 DPI.
2. Next Page Button: Press this button to go forward one page while web browsing.
3. Previous Page Button: Press this button to go back one page while web browsing.

Instructions

1. Remove the battery cover.

2. Insert 2 AAA batteries (not included) into the battery slot.

3. Remove the nano receiver and insert it into the computer’s USB port. The driver will automatically install.

4. Press the DPI switch to shift to the desired DPI level.

5. LED Indicator

The red indicator flashes continuously if the battery is low.

Specifications

Attention

Don’t expose to liquids
Don’t disassemble
Avoid dropping
Avoid extreme temperatures

Troubleshooting

1. Make sure the nano receiver is plugged into your device’s USB port. If it is still unresponsive. plug the receiver into another USB port on your device.
2. Your mouse is not paired with the nano receiver. To pair: Turn on the mouse, plug the nano receiver into your device’s USB port, and then hold the scroll wheel and the right button of the mouse simultaneously. Release the two buttons after 3 seconds to finish paring. If unsuccessful, unplug the receiver, turn off the mouse. and then repeat the above steps to restart pairing. During pairing, make sure the mouse is close to the receiver.

Declaration of Conformity

This product complies with the radio interference requirements of the European Community. Hereby, Anker Innovations Limited declares that the radio equipment type A7852M is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: https://www.anker.com/products
Maximum output power: 5.46dBm
Frequency band: 2.4G band (2403-2479 MHz)
Anker Innovations Deutschland GmbH
Georg-Muche-Strasse 3. 80807 Munich. Germany

Declaration of Conformity

This product complies with the radio interference requirements of the European Community. Hereby, Anker Innovations Limited declares that the radio equipment type A7850 is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: https://www.anker.com/products
Maximum output power: -6.55dBm
Frequency band: 2.4G band (2403-2479 MHz)
Anker Innovations Deutschland GmbH
Georg-Muche-Strasse 3. 80807 Munich. Germany

GB Declaration of Conformity

Hereby, Anker Innovations Limited declares that the product type A7852M is in compliance with the Radio Equipment Regulations 2017 and the Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment Regulations 2012. The full text of the GB declaration of conformity is available at the following internet address: https://www.anker.com

Anker Technology (UK) Limited.
GNR8, 49 Clarendon Road, Watford. Hertfordshire, WD17 1 HP, United Kingdom

GB Declaration of Conformity

Hereby. Anker Innovations Limited declares that the product type A7850 is in compliance with the Radio Equipment Regulations 2017 and the Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment Regulations 2012. The full text of the GB declaration of conformity is available at the following internet address: https://www.anker.com

Anker Technology (UK) Limited.
GNR8, 49 Clarendon Road, Watford. Hertfordshire. WD17 1 HP. United Kingdom

Wireless Vertical Ergonomic Mouse
Model NO:A7852M   FCC ID:2AOKB-A7852M1   IC:23451-A7852M1   HVIN:A7852M1

IC NOTICE TO CANADIAN USERS

This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) This device must accept any interference, including interference that may cause undesired operation of the device. This device complies with RSS-210 of Industry Canada. Operation is subject to the condition that this device does not cause harmful interference. This Class B digital apparatus complies with Canadian ICES-003

FCC STATEMENT

1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including interference that may cause undesired operation.
2. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates uses and can radiate radio frequency energy and. if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However. there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception. which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

Nano Receiver
Model NO:A7850   FCC ID:2AOKB-A7850R1   IC:23451-A7850R1   HVIN:A7850R1

IC NOTICE TO CANADIAN USERS

This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) This device may not cause interference. and (2) This device must accept any interference, including interference that may cause undesired operation of the device. This device complies with RSS-210 of Industry Canada. Operation is subject to the condition that this device does not cause harmful interference. This Class B digital apparatus complies with Canadian ICES-003

FCC STATEMENT

1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
   (1) This device may not cause harmful interference.
   (2) This device must accept any interference received, including interference that may cause undesired operation.

2. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device. pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates uses and can radiate radio frequency energy and. if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on. the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

This symbol means the product must not be discarded as household waste. and should be delivered to an appropriate collection facility for recycling. Follow local rules and never dispose of the product and rechargeable batteries with normal household waste. Correct disposal of old products and rechargeable batteries helps prevent negative consequences for the environment and human health.

Wireless Vertical Ergonomic Mouse
Model No.: A7852M
Nano Receiver
Model No.: A7850
Anker Innovations Limited
Room 1318-19, Hollywood Plaza. 610 Nathan Road. Mongkok. Kowloon, Hong Kong

The device has been evaluated to meet general RF exposure requirement.
The device can be used in portable exposure condition without restriction.

Customer Service

| 18-month limited warranty
---|---
| Lifetime technical support
| support@anker.com
| (US) +1 (800) 988 7973 Mon-Fri 9:00 – 17:00 (PT)
(UK) +44 (0) 1604 936200 Mon-Fri 6:00 – 11:00 (GMT)
(DE) +49 (0) 69 9579 7960 Mon-Fri 6:00 – 11:00

For FAQs and more information, please visit:

@Anker
@Anker Japan
@Anker Deutschland

@AnkerOfficial
@Anker_JP

@Anker

A7852M/A7850
51005001119 V03

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>