SmartWhale Cleanslet-2 Electric Bidet Toilet Seat User Guide

SmartWhale Cleanslet-2 Electric Bidet Toilet Seat

Confirmation before use

Open valve

Open the inlet valve to provide water for the whole machine.

Confirmation and commissioning

1. Check power supply.
   Confirm that the power plug is plugged in tightly and the indicator light on the plug is on, indicating that the system has been powered on. If the indicator light is not on, you can press the “reset” button on the plug to power on. After power on, you can hear the “tick” sound of the system buzzer.

2. Human-body seating sensor
   In the area shown in the figure, someone raises the seat sensing. The system function can be enabled only when the system senses that someone is seated

3. Check basic functions
   When the human body seating sensing is on, press the ” ” or ” ” function on the quick panel to start the corresponding function

4. Check the drying function
   When the human body is seated in the conduction state, press the “ ” function on the quick panel to start the corresponding function

This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:

1. this device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.

Changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment.

The device has been evaluated to meet general RF exposure requirement

How to use

Quick use of knob

How to use the button

Water temperature button: Short press the button to switch the water temperature to levell, level2, level3, off, and cycle in turn. Long press the button to switch the nozzle moving or fixed cleaning state when using the rear wash/female wash function Seat temperature button: Short press the button to switch the seat temperature to levell, level2, level3, off, and cycle in turn. Long press the button to switch the nozzle possition to level 1, level2, level 3, level2, level 1, and cycle in turn when using the rear wash/female wash function.

How to use the control remote

■     Stop| •     Press the stop button to end the running function such as “rear wash”, “female wash”, “air drying” and “pulse wash”.
---|---
■  RearWash

/Moving

| •    When the seat ring senses by its sensing are that someone is sitting, and press the Rear Wash button in stop or other modes, it will start the washing function after a beep, and stop after 90 seconds. If the person leaves the seat ring during the function is running, the function will be stopped.
■  Female Wash

/Moving

| •    When the seat ring senses by its sensing are that someone is sitting, and press the Female Wash button in stop or other modes, it will start the washing function after a beep, and stop after 90 seconds. If the person leaves the seat ring during the

function is running, the function will be stoooed.

■  PowerWash| •     When the seat ring senses by its sensing are that someone is sitting, and press the Power Wash button in stop or other modes, it will start the washing function after a beep, and stop after 90 seconds. If the person leaves the seat ring during the function is running, the function will be stoooed.
■  Air Drying| •        When the seat ring senses by its sensing are that someone is sitting, and press the Air Drying button in stop or other modes, it will start the drying function after a beep, and stop after 3 minutes. If the person leaves the seat ring during the function is running, the function will be stopped.
■  Water temperature| •    Press the water temperature button to increase the water temperature in the “rear wash” and “female wash” modes. It has three levels and stand-by mode. 3 level is the highest and stand-by mode means all the indicated lights are off.
■Air temperature| •    Press the Air temperature button to change the air outlet temperature in the “air drying” mode. The outlet air temperature has 3 levels and stand-by mode. 3 level is the highest and stand-by mode means all the indicated lights are off.
■ Seat temperature| Press the seat temperature button to change the temperature of the seat ring. The

•        seat ring temperature has 3 levels and stand-by mode. Level 3 is the highest and stand-by mode means all the indicated lights are off.

■  Recommended mode| •     Press the recommended mode to use the preset setting.
■  Nozzle cleaning| •     Press the nozzle cleaning button, and the nozzle will come out. Then the cleaning

hole will spray water to clean the nozzle for IO seconds. Press stop button to stop it when it is running.

■  ECO| •    Press the ECO button to start power-saving function (the buzzer rings once); press the button again to stop the power-saving function (the buzzer rings twice for a

short time). The seat temp. will be 28·c in the ECO mode.

■  Child wash| •    Press the Child Wash button in stop or other modes, it will start the washing function after a beep, and stop after 90 seconds. In the child wash mode, the water pressure is level 1, the position is level 3, the water temperature is level 1, and the seat ring is level I (People don’t have to sit on the toilet seat when use this function).
■  Nightligh| •    Turn on or turn off the decorative light of the control knob.
■  Code matching| •     Press and hold the “Female wash” button on remote control for 3 seconds, and the three indicators on the remote control will flash red. At the same time, the machine is powered on, and the buzzer will make a long beep to indicate that the code is successfully paired. Otherwise, repeat the above actions again.
■ Washing Position| •    Press the Washing Position button to change the water position
■ Washing Pressure| •   Press the Washing Pressure button to change the water pressure

Function description

seated, red in rear wash function, blue in female wash function, and flashes red when a fault occurs
Shortcut Function| ECO| Save power when not in use

Care Function

|

Seat Heating

|

Make people not feel cold

Lid Slow Close

|

The damping device is used to make the seat ring, the lid flips smoothly and the noise is small

Safety Function|

Overheating Protection

|

Thermal fuse to prevent the water temperature and seat temperature from being too high

Anti-scald System| After sitting for 15 minutes, the seat temperature will be automatically adjusted to level 1.
Secondary Function| Control Knob| The knobs and buttons on the side of the toilet lid can be

used when the remote control fails

Manual Flushing| Manual flushing during power outages
Clean Function| Troubleshooting| Sense abnormality and remind
Nozzle self-cleaning| The nozzle will be cleaned by strong water pressure before and after use
Nozzle cleaning| Clean the nozzle

The function of the remote controller shall be subject to the actual object

Cleaning procedure

Product Cleaning

1. Power cut
   Unplug the power plug before cleaning the product body.

2. Nozzle Cleaning
   Press the “nozzle cleaning” button on the panel of the remote control, and the nozzle will automatically come out to facilitate the user to clean. Use a soft cloth or soft-bristled toothbrush to dip into the kitchen and wipe the nozzle with detergent. You can also remove the nozzle for cleaning. The method is holding the spray lance in one hand (not shaking) and pull out the spray nozzle with the other hand, and the spray nozzle will be taken out. After cleaning it can be installed back. Finally, press the “stop” button, and the spray lance will return automatically

3. Clean the external parts of the product
   Clean the product with a soft cloth and neutral detergent. Do not use hydrogen chloride cleaner, thinner, benzene, sandpaper, polishing machine, perfume and insecticide and other cleaning products

4. Clean the filter screen
   When users feel that the water flow is less than normal during use, they can clean both ends of the filter screen with a brush. The product must be completely separated from the water supply hose during cleaning. If the product is connected to an external filter, please replace it regularly according to the water quality.

Not in use for long time

Drain and cut off the power supply

1. Pull the plug out.
2. Close the valve and stop supplying water to the system. Remove the water inlet hose from the water inlet valveand drain the water in the hose
3. Press and hold the push rod in the direction of arrow 1 and then horizontally remove the toilet in the opposite direction of the water tank (arrow 2).

CAUTION

When using the product again, please confirm and test run (refer to the part Product Installation).

Quick judgment and maintenance for the troubles

If you think there is a fault, please read the following items first and take measures. If the fault cannot be solved, please contact the purchase place, exclusive store or our customer service center

Please unplug the power cord before maintenance.

CAUTION

• When the power cord is damaged, it shall be replaced by the manufacturer, after-sales service center or professional personnel (with qualification certificate) to avoid safety accidents.
• In case of water leakage, first rotate the handle of the inlet valve clockwise, close the valve and stop water supply

Important

Please confirm the following precautions before maintenance

Power

Function non-responding

| •   Is there power outrage? Is there power in the power socket?

•   Is the main power turned on?

|

•  Please wait until power is restored. Please turn on the power socket.

•  Please turn on the main power.

Rear wash/Female wash/Pulse wash

No water

| •   Is water cut off?

•   Is water valve closed?

•   Did you not touch the sensing area?

| •   Please wait for water.

•   Please open the water valve.

•   Please sit on the sensing area.

Water pressure is decreasing

| •   Is the warm water switch off or the water temperature setting is low?

•   Is the filter or external filter clogged?

| •   Turn up the water pressure by control knob or remote control.

•   Clean the filter; Change the external filter regularly

Water temperature is low

| •  Is the warm water switch off or the water temperature setting is low?| • Adjust the water temperature by control button or remote control

Stop spraying water after 90s of washing

|

•Justa setting. Not a fault problem

| •     Use the washing functions again
Fault Problem| Checking| Solution
---|---|---

Water stop during washing

|

•   Probably that the human body doesn’t touch the sensing area of the seat ring

| Adjust sitting position to make sitting on the sensing area

Seated sensing are of the sear ring

It activates the washing or deodorizing function without being seated.|

•  Is the seat be splashed with water or has a wet towel on it?

| •   Please wipe the water off with dry towel;

•   Please take the wet towel away.

Seat heating

Seat temperature is low

|

•  Is the warm seat switch off or the seat temperature setting is low?

•   Is it in ECO mode?

|

•  Adjust the water temperature by control button or remote control;

•   Please wait for 5 mins after seated.

Or turn off ECO mode.

ECO function

ECO function is not activated

|

•  Is power outrage or the power cord be unplugged?

•  Is the battery on the remote control depleted?

|

•   Press the ECO button on the remote control to activate the function

•   Replacement battery.

Remote control

The remote control not responding

| •   Is the battery on the remote control depleted?

•   Is the battery installed incorrectly?

•   Probably that the human body doesn’t touch the sensing area of the seat ring?

| •   Replacement battery.

•   Please install the battery correctly.

•  Adjust sitting position to make sure sitting on the sensing area.

Warm air drying

Air temperature is low

| ****

•   Is the air temp. setting low?

| ****

•  Adjust the air temp. by remote control.

Function stops during drying

| ****

•   Normally it stops after 3 mins of drying

| ****

•   Use this function again.

•  Adjust sitting position to make sure sitting on the sensing area

Air drying is not activated

| ****

•  Probably that the human body doesn’t touch the sensing area of the seat ring

| ****

•  Adjust sitting position to make sure sitting on the sensing area

Others

Dirt not cleaned

| ****

•   Is the water valve fully open?

•  Water pressure too low when sharing water with bathroom.

| ****

•   Open the water valve

Water pipe connection leaking

| ****

•   Is the nut of the connecting pipe not tightened?

| ****

•   Tighten it

If there is any abnormal situation other than the above table, please contact the seller.

Troubleshooting \ ‘

Alert| Knob light alert| Buzzer| Fault description
Seat temp. sensor alert| •   Flash red once| 1 beep| •   Sensor open or short circuit will alarm and stop seat heating
Air temp. sensor alert| •   Flash red twice| 1 beep| •   Sensor open or short circuit will alarm and stop air drying
Water temperature sensor alarm| •   Flash red three| 1 beep| •   The outlet water temperature is greater than 45 ·c. (After

3 subsequent alarms, it returns to normal if there is no

abnormality)

Technical parameters

s

| ****

Cleanslet-2

---|---

Rated power

| ****

120V~     60Hz

Rated power

| 1220W (The inlet water temperature is 15 ‘C, the outlet water temperature is at the maximum level, the water pressure is 0.2MPa, the water pressure is at the maximum level, and 30 seconds before the Rear wash operation).

Power line length

| ****

1.2m

Warm water heating mode

| ****

Instant heating

Water temperature

| The temperature adjustment range is about 30 ·c – 39 ·c

Safety device

| Flow monitoring sensor, water temperature sensor, bimeta temperature control switch, temperature fuse.

Wind temperature

| ****

Adjustable temperature range (room temperature-55°C)

Drying heating power

| –| ****

250W

Seat ring surface temperature

| ****

Adjustable temperature range (room temperature-40°C)

Seat ring heating power

| ****

40W

Water supply pressure| 0.15MPa-0.75MPa
Environment temperature| ****

1-40°C

Product size| ****

L505xW375xH112mm

Product weight

| 3.5kg/7.7lbs

WARNING

• Do not disassemble, repair or refit the product by yourself.
• May cause electric shock, fire or failure

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>