Quattropod LITE2RX Wireless Display HDMI Transmitter Owner’s Manual

Quattropod LITE2RX Wireless Display HDMI Transmitter

What’s in the box

Standard Package

Transmitter only

Connections

Note:
When using the transmitter, make sure to connect the power source first before inserting the HDMI signal source. Additionally, when using a Type C adapter, due to certain signal source restrictions (such as the NS game console), please also connect the transmitter to the power source before inserting the signal source.

Transmitter Operation

• Single Press
• Cast/Pause
• Press and hold for 3 seconds
• Full-screen display
• Press and hold for more than 10 seconds
• Clear pairing and re-pairing

1. Tx and Rx are working through WiFi technology, Tx will connect with Rx’s SSID directly once both are paired.
2. Note: When repairing, make sure to clear the transmitter first before connecting both the receiver and transmitter through the pairing adapter.
3. This product is pre-paired and ready to use out of the box, so there is no need to repair it. However, if you purchase additional transmitters or need to use it with other receivers, you can follow the steps below to re-pair and use them.

Pairing method

1. First, connect the receiver to the power source, but there’s no need to connect it to the display yet.
2. Connect the transmitter to the power source. When the red light starts flashing, press and hold the button. Release the button when the blue light starts flashing rapidly.
3. Once the flashing of the blue light on the transmitter stops and the red light starts flashing, directly connect the transmitter (without disconnecting the power) and the receiver Rx (without disconnecting the power) using the pairing connector. This will initiate a re-pairing process (indicated by the rapid flashing of the red light).
4. After the pairing process is complete, the transmitter light will turn steady red. You can then disconnect the transmitter and receiver and restart to begin using the system again.

Note:
Do not press and hold the transmitter button while connecting it to the power source to avoid system errors.

LED Status list

Safety Precautions

Please observe the following safety precautions when operating the device:

• Please ensure that this device is kept away from water.
• Use only the accessories provided in the package.
• Do not operate this device during storms or heavy rain.
• Do not cover or block any ventilation openings of this device.
• Do not place this device in a damp or high-humidity environment.
• Before turning on the device, make sure all cables are correctly connected.
• Protect all cables and the power adapter from being stepped on or crushed by heavy objects.
• Before cleaning, unplug the power adapter. Use a clean, dry cloth to wipe the device.
• Do not attempt to repair this device on your own.
• Keep this device away from direct sunlight.
• Do not drop or subject this device to severe impacts.
• The operating environment temperature of this device should not exceed 40 degrees Celsius.

FCC STATEMENT

1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
2. This device may not cause harmful interference.
3. This device must accept any interference received, including interference that may cause undesired operation.
4. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

NOTE:
This equipment has been tested and found to comply with the limits for a Class B digital device, according to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates uses and can radiate radio frequency energy and, if not installed and used per the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

FCC Radiation Exposure Statement

Receiver:
To maintain compliance with FCC’s RF Exposure guidelines, This equipment should be installed and operated with a minimum distance of 20cm from the radiator of your body. This device and its antenna(s) must not be co-located or operated in conjunction with any other antenna or transmitter.

Transmitter:

SAR statement
This device meets the government’s requirements for exposure to radio waves. This device is designed and manufactured not to exceed the emission limits for exposure to radio frequency (RF) energy set by the Federal Communications Commission of the U.S. Government. The SAR limit set by the FCC is 1.6W/Kg. For body-worn operation, this device has been tested and meets the FCC RF exposure guidelines for use with an accessory that contains no metal and positions the device a minimum of 0mm from the body.

RF exposure compliance with any body-worn accessory that contains metal was not tested and certified. and use of such body-worn accessories should be avoided. Accessory available in market and must be used to keep use distance 0mm from EUT to body-worn operation.

TELEC
Note: 5G band (W52) indoor use only.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>