Lucci 099040 Alfred 1 Light Batten Fix Chrome Glass Installation Guide
- June 21, 2024
- Lucci
Table of Contents
Lucci 099040 Alfred 1 Light Batten Fix Chrome Glass
Specifications
- Product Name: ALFRED 1 LIGHT DIY BATTEN FIX
- SKU: 099040, 099042, 099043, 099943
- Installation: DIY (onto existing batten holder)
Product Usage Instructions
Installation Requirements
Ensure the existing batten holder is in good working condition, and the
plastic has not become cracked, brittle, or discolored.
If the batten holder is damaged in any way, return the complete product to the
place of purchase for inspection, repair, or replacement.
Installation Directions – For Batten Holder Only:
- Ensure power to the batten holder has been switched OFF before starting the installation.
- Remove all packaging material from the product, ensuring not to discard any hidden accessories.
- If the glass shade is not tightly fixed with one silicon washer, use an additional washer.
- Do not exceed the 45W maximum globe rating after installation.
- Check that the product is fully assembled and all parts are secure before turning on the power to the batten holder. Test the product before use.
Installation Directions – For Lucci Create II Lamp Holder Exposed (Sold Separately):
- Ensure power to the luminaire has been switched OFF before beginning the installation.
- Unpack the product carefully to avoid discarding any hidden accessories.
- If the glass shade is not tightly fixed with one silicon washer, use an additional two to three full threads.
- Do not exceed the 45W maximum globe rating after installation.
- Confirm that the product is fully assembled and all parts are secure before switching on the power to the luminaire. Test the product functionality.
FAQ
-
Q: What should I do if the glass shade is not fixed tightly after installation?
A: If the glass shade is not tight, check if it was installed with a silicon washer. If not, add an additional washer as instructed in the manual. -
Q: What is the maximum globe rating I should not exceed after installation?
A: Do not exceed the 45W maximum globe rating after installing this product to ensure safety and proper function.
ALFRED 1 LIGHT DIY BATTEN FIX
SKU# 099040, 099042, 099043, 099943
DIY (Installation onto existing batten holder)
Thank you for purchasing this quality Lucci product. To ensure correct
function and safety, please read and follow all instructions carefully before
assembly, installation and use of this product. Please keep instructions for
future reference.
Warranty
- This product is covered by a 12-month warranty valid for in-store replacement or refund only.
- The warranty period starts from the date of purchase. Please retain the proof of purchase.
- Warranty will be void if there is any damage due to improper usage or modification to the product.
- Failure to comply with the instructions in this manual may increase the risk of damage or injury and will void the warranty.
Installation Requirements
- This product is a DIY (Do It Yourself) product, no electrical wiring connection or disconnection is required. The service of a licensed electrician is not required.
- This product is designed to be used with a batten holder (not included).
- The installation location must have an existing batten holder (not included) pre-installed.
- If you don’t have a batten holder (not included), please contact your licensed electrician.
NOTE: Ensure the existing batten holder (not included) is in good working condition, and the plastic has not become cracked, brittle or discoloured.
- This product is suitable for indoor use only.
- Do not exceed the maximum globe wattage rating after the installation of this DIY product.
- Lay out all the components on a smooth surface and make sure there are no components missing before assembling. If parts are missing, return the complete product to the place of purchase for inspection or replacement.
- Check whether the product has been damaged during transport. Do not operate/install any product which appears damaged in any way. Return the complete product to the place of purchase for inspection, repair or replacement.
NOTE: There are 4 different installation directions in this instruction manual:
- 1st installation method: For batten holder only – refer to page 2.
- 2nd installation method: For Lucci Create II (sold separately) Lamp holder exposed: SKU# 011444, 011445, 011446, 011447, 011448 & Lucci Create II finishing kit SKU 011466,011467, 011468, 011469, 011470- refer to page 3.
- 3rd installation method: For Lucci Create II (sold separately) Lamp holder hidden: SKU# 011444, 011445, 011446, 011447, 011448 & Lucci Create II finishing kit SKU 011466,011467, 011468, 011469, 011470- refer to page 4.
- 4th installation method: For Lucci Darly (sold separately): SKU# 099073, 099074- refer to page 5.
Installation Directions-For batten holder only
NOTE: Ensure power to the batten holder you are working on has been switched OFF before commencing the installation.
-
Remove all packaging material from the product and be careful not to throw away accessories that may be hidden within the packaging material.
-
Remove the skirt (F – not included) from the batten holder (A – not included).
-
Install the batten cover (B) over the batten holder (A – not included) followed by the glass shade (C), silicon washer (D), skirt cover (E) and secure with the skirt (F– not included).
NOTE : Ensure that the skirt (F – not included) is attached securely. Check that it has taken up at least 2-3 full threads while attaching the skirt (F – not included) to the batten holder (A – not included).
NOTE : If the glass shade(C) is not fixed tightly by installing with one silicon washer (D), use additional washer provided. -
Install a globe (G – not included) into the batten holder (A – not included).
NOTE : Do not exceed the 45W maximum globe rating after the installation of this DIY product. -
Check and ensure the product is fully assembled and all parts are secure before turning on the power to the batten holder. Switch on the product to test and enjoy your new lighting product.
Installation Directions-For Lucci Create II Lamp Holder Exposed (Sold Separately)
Compatible pendants: Lucci Create II suspension (sold separetely): SKU#
011444, 011445, 011446, 011447, 011448 &
Lucci Create II finishing kit SKU 011466,011467, 011468, 011469 , 011470
WARNING: Ensure power to the luminaire you are working on has been
switched OFF before commencing the installation.
-
Remove all packaging material from the product and be careful not to throw away accessories that may be hidden within the packaging material.
-
Remove the lamp holder ring (H – not included) from the lamp holder (K – not included).
-
Install the assembled shade (C) onto the lamp holder (K – not included) and secure by installing the silicon washer (D) followed by the lamp holder ring (H- not included) back onto the lamp holder (K– not included).
NOTE : Ensure that the lamp holder ring (H– not included) is attached securely. Check that it has taken up at least
2-3 full threads.
NOTE : If the glass shade (C) is not fixed tightly by installing with one silicon washer(D), install the additional washer provided. -
Install a globe (N – not included) into the lamp holder (K– not included).
NOTE : Do not exceed the 45W maximum globe rating after the installation of this DIY product. -
Check and ensure the product is fully assembled, and all parts are secure before turning on the power to the luminaire. Switch the power ON to test and enjoy your new lighting product.
Installation Directions-For Lucci Create II Lamp Holder Hidden (Sold
Separately)
Compatible pendant s: Lucci Create II suspension (sold separetely): SKU#
011444, 011445, 011446, 011447, 011448 &
Lucci Create II finishing kit SKU 011466,011467, 011468, 011469 , 011470
WARNING: Ensure power to the luminaire you are working on has been switched OFF before commencing the installation.
-
Remove all packaging material from the product and be careful not to throw away accessories that may be hidden within the packaging material.
-
Remove the lamp holder ring (H– not included) and the lamp holder cover (J – not included) from the lamp holder (I –not included).
-
Thread the lamp holder ring (H – not included) back over lamp holder (K – not included) and move the lamp holder ring (H- not included) to the threaded component above the lamp holder (M – not included).
-
Install the assembled shade (C) onto the lamp holder (K – not included) and secure by installing the silicon washer (D) followed by the lamp holder cover (J – not included) back onto the lamp holder (K – not included).
NOTE : Ensure that the lamp holder ring (H– not included) is attached securely. Check that it has taken up at least 2-3 full threads.
NOTE : If the glass shade(C) is not fixed tightly by installing with one silicon washer (D), use additional washer provided. -
Install a globe (N – not included) into the lamp holder (K – not included).
NOTE : Do not exceed the 45W maximum globe rating after the installation of this DIY product. -
Check and ensure the product is fully assembled, and all parts are secure before turning on the power to the batten holder. Switch the power ON to test and enjoy your new lighting product.
Installation Directions-For Lucci Darly (Sold Separately)
Compatible pendants: Lucci Darly (sold separetely): SKU# 099073, 099074
WARNING: Ensure power to the luminaire you are working on has been
switched OFF before commencing the installation.
-
Remove all packaging material from the product and be careful not to throw away accessories that may be hidden within the packaging material.
-
Remove the skirt (F – not included) from the lamp holder (Q – not included).
-
Install the assembled shade (C) onto the lamp holder (Q – not included) followed by the silicon washer (D), skirt cover (E) and the skirt (F – not included) back onto the lamp holder (Q – not included) to secure everything together.
NOTE : Ensure that the skirt (F – not included) is attached securely. Check that it has taken up at least 2-3 full threads while attaching the skirt (F – not included) to the lamp holder (Q – not included).
NOTE : If the glass shade(C) is not fixed tightly by installing with one silicon washer (D), use additional washer provided. -
Install a globe (G – not included) into the lamp holder (Q – not included).
NOTE : Do not exceed the 45W maximum globe rating after the installation of this DIY product. -
Check and ensure the product is fully assembled, and all parts are secure before turning on the power to the luminaire. Switch the power ON to test and enjoy your new lighting product.
Safety Tips
- Always ensure the power is OFF and the product has cooled down before performing any maintenance, cleaning, changing the globe or adjustment to the product.
- Do not touch the globe with bare hands. Use a clean cloth, gloves or a tissue.
- To avoid injury or damage to the product, ensure that power leads and screws are secure before connecting the power.
- Select a suitable location away from liquids and hazards.
- Ensure that the product does not come in contact with corrosive chemicals, etc.
- To clean, wipe with a damp clean cloth. Never soak the product with water.
Specifications
SKU #| 099040| 099042| 099043| 099943
Colour| Chrome / Clear Glass
Shade
| Black/ Clear Glass
Shade
| Oil Rubbed Bronze/
Clear Glass Shade
| Aged Brass/ Clear
Glass Shade
Globe Wattage| 45W Max. (After the installation of this DIY product)
Lamp Holder| BC/B22 – Installation onto existing batten holder (not included)
Weight| 1.2 kg
Dimensions| H:180mm Dia:300mm
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>