Sunco DL_ RE6_S-WH 6 Inch Retrofit Smart Downlight User Manual
- June 21, 2024
- SUNCO
Table of Contents
Lighting made better.
User Manual
6” Retrofit Smart Downlight
SKU: DL_ RE6_S-WH
Whats in the Box?
Retrofit Downlight
Before You Start
Safety Information
To reduce the risk of fire, electric shock, or physical injury:
- Turn off circuit breaker before installing fixture.
- Suitable for damp locations at temperatures ranging from -4°F to 104°F.
- Not intended for use with emergency fixtures.
- Not compatible with all dimmers. For more dimming information, please visit www.sunco.com
- Not compatible with timing devices.
- Not compatible with third party sensors.
- Not compatible with photo-electric sensors.
- Not compatible with motion sensors.
- All electrical connections must be in accordance with local and National Electric Code (N.E.C.) standards.
- Please review installation manual carefully before proceeding. Consult a qualified electrician if you are unfamiliar with proper electrical wiring connections.
WARNING:
Cancer & Reproductive Harm-
www.P65Warnings.ca.gov
This device complies with Part 15 of the FCC rules.
Operation is subject to the following two conditions:
- This device may not cause harmful interference.
- This device must accept any interference that may cause undesired operation. Please review all instructions carefully prior to installation.
Quickstart Guide
Step 1
Locate the recessed housing.
Step 2
Determine type of connector available.
Step 3
Connect the adapter to make connection.
Step 4
Push downlight into can until secure.
Installation Guide
STEP 1
a. Turn off circuit breaker before installation.
b. Locate the housing.
NOTE: Remove previous fixture. Fixture may be hot so allow time to cool
after turning off power.
STEP 2
Determine the type of connector available.
-TP24 Connector(1)
-E26 Base(2)
STEP 3
a. Connect the appropriate adapter to make connection in the housing.
NOTE: the wires may come lose from the connectors so ensure they are
attached.
b. Tuck all wires into the can.
STEP 4
a. Line up trim ring with opening.
b. Push downlight into can until secure. Compression clips will hold retrofit
light in place. Push up spring clips and insert into ceiling.
STEP 5
Turn on circuit breaker and test light.
STEP 6
a. To start the pairing process, initiate pairing mode first and then use the
Sunco app to set up and configure your device.
b. Please refer to the pairing instructions on the next page for guidance on
completing the pairing process.
Product Details
Install Sunco Smart App
Install Sunco Smart Lighting App. Search for “Sunco Smart Lighting”.
Register Your Account
Register using your mobile phone number or email address to receive a
verification code and press next. Enter verification code and press next.
Create password for your account and press next.
Adding Lights
To activate pairing mode, simply toggle the wall switch OFF and ON five times
in quick succession. Then, effortlessly configure your device by utilizing the
Sunco App and following the intuitive on-screen prompts.
Note: For proper functioning, this smart light requires a 2.4 GHz
connection.
Specifications
Voltage | 120V |
---|---|
Wattage | 14W |
Power Factor | 0.7 |
CCT | 2700K-6500K |
Weight | 0.45lbs |
Housing Material | PA |
Dimmable | Via App |
Average Lifetime | 50000 hrs |
Lumens | 1200LM |
Moisture Rating | Damp |
CRI | 80+ |
Usage | Indoor |
Frequency | 60Hz |
Warranty | 7 Years |
Common Troubleshooting
Feeling in the dark about an issue with your product? No worries! Our
troubleshooting section is here to shed some light and provide you with easy-
to-follow solutions for any problem.
If you still need some assistance, please feel free to contact us with any
questions. Our team of lighting experts are happy to help brighten your day.
Installation
Light isn’t turning on.| Double check if fixture is properly connected and
circuit breaker hasn’t been tripped.
---|---
Light unexpectedly fails.| For further assistance, contact our customer
support.
Dimming
Light not dimming to lowest setting.| Ensure minimum dimmer load requirement
is met.
---|---
Light not dimming smoothly.| Dimming only accessible via the app.
Light not compatible with dimmer switch.| Check light-dimmer compatibility.
Consider purchasing compatible switch if necessary.
Flickering
Light is flickering when turning on.| Check that fixture wiring connections
are secure.
---|---
Light flickering with other lights on the same circuit.| Check that the lights
on the same circuit are not overloading the circuit.
Light flickering when turned on.| Verify fixture compatibility.
Light flickering when dimmed.| Dimming only accessible via the app.
Buzzing
Fixture buzzing with power outages.| Verify light is connected to surge
protector securely.
---|---
Fixture buzzing with appliances or electronic devices.| Look for nearby
interferences that can cause buzzing.
Such as televisions, radios, computers, etc.
Fixture buzzing when dimmed.| Dimming only accessible via the app.
Light Distribution Angle
Lighting distribution angle refers to the spread of light emitted from a light
source. It is an important factor to consider when selecting a fixture or
bulb, as it affects the way it will illuminate an area. There are two main
types of lighting distribution angles:
A symmetric lighting distribution emits light evenly in all directions,
creating a cone-shaped pattern that provides a pool of light. This type of
lighting is ideal for general lighting and illuminating large areas. Common
applications for symmetric lighting include general area illumination,
security lighting, and perimeter lighting. Symmetric lighting is also used to
a certain degree in up-lighting.
An asymmetric lighting distribution angle, also known as beam angle, creates a
pattern that focuses light in a specific direction. This type of lighting is
ideal for task lighting as it reduces glare and light spill in other areas.
Common applications include task lighting in spaces such as landscape
settings, retail stores, museums, and much more.
It is important to note that the lighting distribution angle can also be
affected by other factors such as the reflector design of the light source,
the type of lens used, and the distance between the light source and the
surface being illuminated.
Customer Support
Warranty Policy
This product is covered by our industry leading 7 year warranty.
It gets even better – scan the QR code for 2 extra years of protection!
Scan me for two extra years!
https://www.sunco.com/pages/warranty
30 Day Return Policy
At Sunco, we value our customers and stand by the quality and performance of
our products.
If you are not completely satisfied with your purchase, we accept returns
within 30 days of your purchase date.
Customer Service
Our Los Angeles team of lighting experts is here to assist you with all your
needs! Contact us at:
Email: support@sunco.com
Call or Text: 844-334-9938
support@sunco.com
844-334-9938
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>