IZZY 10Lt IZ-8225 Digital Air Fryer Instruction Manual

IZZY 10Lt IZ-8225 Digital Air Fryer Instruction Manual

Thank you for having chosen an appliance from the IZZY range.

Safety interlocks

Please read these instructions carefully before using the appliance and save them for future reference. Please keep the sales receipt for guarantee purposes (pls see below “Guarantee and Customer Service”) Any use which does not conform to the instructions will absolve IZZY from any liability.

• Make sure your electricity supply is the same as the one shown on the underside of the appliance.

• Always plug your device into an outlet that is earthed. Failure to comply with this requirement may result in electric shock and possible serious injury.

• Never leave the appliance unattended when it is operating.

• Close supervision is necessary when your appliance is being used near children or infirm persons. Ensure that they do not play with the appliance.

• This appliance is not intended for use by persons with reduced physical, sensory or mental capabilities, children or those with lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.

• Switch off and unplug
  − After each use
  − Before cleaning
  − Before moving

• Never use the appliance for any other use than indicated.

• The device is intended for indoor use. Do not use the device outdoors.

• The device is intended only for domestic use. Any other use will cancel the warranty.

• Always use the appliance on a secure, dry, clean and heat resistant surface.

• Do not operate or place the device or parts in places of high humidity or where it may get wet.

• Never let the body of the appliance, cord or plug get wet. If the appliance does get wet, immediately remove the power cord from the wall outlet and do not put your hands in the water. Never run the wet appliance and contact one of the authorized BENRUBI service centers.

• Do not place the appliance near heat sources, on or next gas or electric hobs.

• The appliance must have sufficient airflow. Leave more than 10 cm around the appliance.

• Don’t put the appliance near curtains, under shelves or cupboards, or near anything that might be damaged by the escaping steam.

• Don’t cover the appliance or put anything on top of it during use.
  ATTENTION: During use, be careful and do not touch the air outlet, on the back of the appliance. Hot air comes out.

• Misuse of the air fryer can result in injury.

• Do not let the power cord of the appliance hang over the edge of a table or bench top or where a child could grab it. Do not let the power cord to touch any hot surface.

• Never pull the cord to disconnect the appliance from the electrical supply. Instead grasp the plug and pull it to disconnect.

• Never leave the power cable wrapped during use. Unwind it completely.

• Never use highly corrosive or abstractive cleaning agents. Never use metal scouring pads for cleaning.
  CAUTION: The surface of the appliance is hot during operation. Do not touch hot parts of the appliance during operation.
  CAUTION: Do not let the resistance of the appliance to get wet.

• It is suggested that it should not be used for more than 3 hours.

• Do not move the appliance when it is in operation.

• Do not touch the appliance with wet or damp hands.

• Do not use an extension power cord.

• This appliance is not intended to be operated by means of an external timer or separate remote-control system.

• Check the power cord periodically for possible damages. If the power cord or the plug of the appliance has been damaged, do not use the appliance and contact an authorized BENRUBI Service Center.

• In case of a possible damage, do not attempt to repair the appliance by yourself. Please contact one of the authorized BENRUBI service centers.

• Any repair made by an unauthorized BENRUBI Service Center CANCELS THE GUARANTEE.

• Any misuse of the device cancels the warranty.

• Use only original spare parts.

• The appliance conforms to EU directive 2014/30/EU on Electromagnetic Compatibility, the 2014/35/EU Low Voltage Directive, the 2011/65/EU RoHS Directive, the directive 2009/125/EC for eco-design and the EC regulation no. 1935/2004 on materials intended to contact with food.

SAVE THESE INSTRUCTIONS

Parts of the Appliance

1. Air inlet
2. Control panel
3. Bucket separator
4. Detachable non-stick rack
5. Detachable non-stick bucket 10L with window
6. Handle
7. Air outlets
8. Power cord

Control panel

9. Temperature adjustment buttons ∧/∨
10. Zone selection 1
11. Display screen
12. Zone selection 2
13. Time adjustment buttons ∧/∨
14. “PREHEAT” button with indication light
15. “AIR FRY” button with indication light
16. “START/PAUSE” button with indication light
17. “BAKE” button with indication light
18. “SMART FINISH” button with indication light
19. “ROAST” button with indication light
20. “MATCH COOK” button with indication light
21. “BROIL” button with indication light
22. “DEHYDRATE” button with indication light
23. Power button
24. “KEEP WARM” button with indication light
25. “REHEAT” button with indication light
    

Programs and Preset Times and Temperatures

The following table lists the programs and the preset temperatures and times.
Use this table for reference only.

Before the First Use

• Make sure the appliance is switched off and unplugged before use.

NOTE: Smoke and odors may occur during first use.

1. Wash the parts of the appliance. See “Care and Cleaning” section.

2. Place the appliance on a clean, flat and heat-resistant surface.

3. Place the rack (4) in the bucket (5).
   Note: Do not use the appliance without the detachable rack.

4. Insert the bucket in the reception without food until it snaps into place.
   Note: If the bucket does not fit well into the reception, the appliance will not turn on.

5. Plug in. A “beep” will be heard and the power button (23) will remain on.

6. Press the power button (23). A “beep” will sound and all the indication lights on the display screen (10) will turn on.

7. Press “MATCH COOK” button (20). The indication light will flash.

8. Press the “PREHEAT” button (14) The indication light will flash and on the display screen the preset temperature 150 οC and the preset time 15 will alternate.

9. Set the temperature 200οC by pressing the temperature adjustment button ∧ (9).

10. Set the time to 10 minutes by pressing the time adjustment button ∨ (13).

11. Press “START/PAUSE” button (16) and the appliance will start. On the display screen (10) the selected temperature and time will alternate.

12. When the selected program is finished, a “beep” will be heard 11 times. The indication lights will turn off and the indication light of the power button (23) will remain on.

13. The appliance is ready for use.

Using the Appliance

• Make sure the appliance is switched off and unplugged before use.
• It is recommended to preheat the appliance for 5 minutes without food before cooking.
• Do not put a paper liner without food in the airfryer, to avoid it flying away or burning by the heating element.

Regular function **

**

– You can cook two different foods by choosing different program, temperature & time for each one.

1. Place the appliance on a clean, flat and heat-resistant surface.

2. Place the rack (4) in the bucket (5) and slide the bucket separator (3) in the slot in the middle of the bucket.
   Note: Do not use the appliance without the detachable rack.

3. Place the food on the rack (4) and insert the bucket (5) in the reception until it snaps into place.
   Note: Make sure the food in the bucket does not come into contact with the heating resistant.
   Note: If the bucket with the rack do not fit well into the airfryer cavity, the appliance will not turn on.

4. Plug in. A “beep” will be heard and the power button (23) will remain on.

5. Press the power button (23). A “beep” will sound and all the indication lights on the control panel (10) will turn on.

6. Press the zone selection button 1 (10). The indicator light will flash.

7. Press the button of the program of your choice (see section “Table of programs & preset times & temperatures”). The corresponding indication light will flash and the preset temperature and the preset time of the program will alternate on the display screen. Set the temperature and time of your choice by pressing the corresponding temperature (9) and time (13) adjustment buttons.

8. Press the zone selection button 2 (12). The indicator light will flash.

9. Press the button of the program of your choice (see section “Table of programs & preset times & temperatures”). The corresponding indication light will flash and the preset temperature and the preset time of the program will alternate on the display screen. Set the temperature and time of your choice by pressing the corresponding temperature (9) and time (13) adjustment buttons.
   Note: If you do not press any key for 5 minutes, the lights will turn off and the appliance will enter the standby mode and the power indication (23) will remain on.

10. Press the “START/PAUSE” button (16) and the appliance will start. The internal light will turn on.
    Note: The internal light will remain on for 3 minutes and then will turn off.

11. On the display screen the selected temperature and time will alternate.
    Note: During cooking, it is recommended to stir or turn the food in the bucket for best results:
    – Press the START/CANCEL button (16), remove the bucket, mix and reinsert the bucket. Press the START/CANCEL button again and the selected program will automatically resume.
    Note: If you do not insert the bucket within 5 minutes, the selected program is cancelled. The lights will turn off, the appliance will enter into standby mode and the power indication light (23) will remain on.

12. When the selected program is finished, a “beep” will be heard 11 times. The indication lights will turn off and the indication light of the power button (23) will remain on.
    Note: If the times you have selected are different, when the shorter one is completed a “beep” will be heard and the half side will stop working.
    Note: Before serving, check that the food has been cooked. If it takes extra time to cook, repeat the process by adjusting the time and temperature. Cooking time depends on the density, thickness and humidity of the food.

“MATCH COOK” function

• With the “MATCH COOK” function you can cook:
  – larger amount of food by using the whole bucket (without the separator).
  or
  – two different foods by using the separator (3) and by choosing common program, temperature and time.

1. Place the appliance on a clean, flat and heat-resistant surface.

2. Place the rack (4) in the bucket (5) and slide the bucket separator (3) in the slot in the middle of the bucket.
   Note: Do not use the appliance without the detachable rack.

3. Place the food on the rack (4) and insert the bucket (5) in the reception until it snaps into place.
   Note: Make sure the food in the bucket does not come into contact with the heating resistant.
   Note: If the bucket with the rack do not fit well into the airfryer cavity, the appliance will not turn on.

4. Plug in. A “beep” will be heard and the power button (23) will remain on.

5. Press the power button (23). A “beep” will sound and all the indication lights on the control panel (10) will turn on.

6. Press the “MATCH COOK” button (20). The indicator light will flash.

7. Press the button of the program of your choice (see section “Table of programs & preset times & temperatures”). The corresponding indication light will flash and the preset temperature and the preset time of the program will alternate on the display screen. Set the temperature and time of your choice by pressing the corresponding temperature (9) and time (13) adjustment buttons.
   Note: If you do not press any button for 5 minutes, the lights will turn off and the appliance will enter the standby mode and the power indication (23) will remain on.

8. Press successively the temperature setting buttons (9) to set the temperature of your choice.

9. Press successively the time setting buttons (13) to set the temperature of your choice.

10. Press the “START/PAUSE” button (16) and the appliance will start. The internal light will turn on.
    Note: The internal light will remain on for 3 minutes and then will turn off.

11. On the display screen the selected temperature and time will alternate.
    Note: During cooking, it is recommended to stir or turn the food in the bucket for best results:
    – Press the START/CANCEL button (16), remove the bucket, mix and reinsert the bucket. Press the START/CANCEL button again and the selected program will automatically resume.
    Note: If you do not insert the bucket within 5 minutes, the selected program is cancelled. The lights will turn off, the appliance will enter into standby mode and the power indication light (23) will remain
    on.

12. When the selected program is finished, a “beep” will be heard 11 times. The indication lights will turn off and the indication light of the power button (23) will remain on.

Note: Before serving, check that the food has been cooked. If it takes extra time to cook, repeat the process by adjusting the time and temperature. Cooking time depends on the density, thickness and humidity of the food.

“SMART FINISH” function

• With the “SMART FINISH” function you can cook
  – two different foods, by choosing different program, temperature and time for each one. With this function the appliance will automatically complete both programs at the same time.

1. Place the appliance on a clean, flat and heat-resistant surface.

2. Place the rack (4) in the bucket (5) and slide the bucket separator (3) in the slot in the middle of the bucket.
   Note: Do not use the appliance without the detachable rack.

3. Place the food on the rack (4) and insert the bucket (5) in the reception until it snaps into place.
   Note: Make sure the food in the bucket does not come into contact with the heating resistant.
   Note: If the bucket with the rack do not fit well into the airfryer cavity, the appliance will not turn on.

4. Plug in. A “beep” will be heard and the power button (23) will remain on.

5. Press the power button (23). A “beep” will sound and all the indication lights on the control panel (10) will turn on.

6. Press the “SMART FINISH” button (18). The indicator light will flash.

7. Press the zone selection button 1 (10). The indicator light will flash.

8. Press the button of the program of your choice (see section “Table of programs & preset times & temperatures”). The corresponding indication light will flash and the preset temperature and the preset time of the program will alternate on the display screen. Set the temperature and time of your choice by pressing the corresponding temperature (9) and time (13) adjustment buttons.

9. Press the zone selection button 2 (12). The indicator light will flash.

10. Press the button of the program of your choice (see section “Table of programs & preset times & temperatures”). The corresponding indication light will flash and the preset temperature and the preset time of the program will alternate on the display screen. Set the temperature and time of your choice by pressing the corresponding temperature (9) and time (13) adjustment buttons.
    Note: If you do not press any button for 5 minutes, the lights will turn off and the appliance will enter the standby mode and the power indication (23) will remain on.

11. Press the “START/PAUSE” button (16) and the appliance will start. The internal light will turn on.
    Note: The internal light will remain on for 3 minutes and then will turn off.

12. On the display screen the selected temperature and time will alternate.
    Note: During cooking, it is recommended to stir or turn the food in the bucket for best results:
    – Press the START/CANCEL button (16), remove the bucket, mix and reinsert the bucket. Press the START/CANCEL button again and the selected program will automatically resume.
    Note: If you do not insert the bucket within 5 minutes, the selected program is cancelled. The lights will turn off, the appliance will enter into standby mode and the power indication light (23) will remain on.

13. When the selected program is finished, a “beep” will be heard 11 times. The indication lights will turn off and the indication light of the power button (23) will remain on.

Note: Before serving, check that the food has been cooked. If it takes extra time to cook, repeat the process by adjusting the time and temperature. Cooking time depends on the density, thickness and humidity of the food.

Notes:

• Carefully remove the bucket from the reception. Always hold the bucket (5) by the handle (6).
• When removing the bucket, be careful as steam may escape.
• Serve using plastic or wooden tongs.
• If you want to change the time or temperature during operation, press the temperature (9) and/or time (13) adjustment buttons and set the temperature or time accordingly.
• If you want to change the program during operation, press the START/CANCEL button (16). Select the program you want, set the temperature & time and press the START/CANCEL button (16) again.
• If you want to stop the program before the selected time, press the function button (23).
• Do not cover the device or place anything on it during use.
• Do not fill the basket with oil or any other liquid.
• Do not place flammable containers made of cardboard, paper, plastic and similar materials into the device.
• Do not place glassware, closed containers and similar materials that may break with the temperature.
• Do not use glass or ceramic utensils.
• If you do not press any button for 5 minutes, the lights will turn off and the appliance will enter the standby mode and the power indication (23) will remain on.
• In the event of electricity disconnection, when the power is restored, the appliance will continue to work from the time it has stopped and complete the program you had set.
• In the event of a power outage, when the power is restored, the program of your choice continues from the time it has stopped.

Tips

• Add 1-2 tablespoons of oil (depending on the amount) and stir before cooking.
• Smaller ingredients usually require less cooking time than larger ingredients.
• To ensure uniform cooking, in the middle of the cooking time, it is recommended to mix the food in the frying basket during cooking.
• Snacks that are normally baked in the oven can also be cooked in the fryer.
• Cooking extremely fatty ingredients is not recommended.
• The ideal quantity for preparing crispy potatoes is 500 grams to use half the bucket and 900 grams to use the whole bucket.
• Use pre-made dough to make filling snacks quickly and easily. Pre-made dough also requires less preparation time than homemade dough.
• Place a baking tin or baking tray on the detachable rack if you want to bake a cake or quiche or if you want to fry brittle or stuffed ingredients.
• The appliance is suitable for heating food. To reheat your food, set the temperature to 150℃ for up to 10 minutes.

Care and Cleaning

• Before cleaning and storage, unplug the appliance and let it cool down for at least 30 minutes.
• Always clean the appliance and accessories after each use.

Body:

• Wipe with a damp cloth, then dry.
• Never use highly corrosive or abstractive cleaning agents.
• Never use metal scouring pads for cleaning.

Detachable rack, bucket & separator:

• Wash with warm soapy water and dry thoroughly.
• Never use highly corrosive or abstractive cleaning agents.
• Never use metal scouring pads for cleaning.
• It is recommended not to wash the parts in the dishwasher.

Technical Characteristics

Model: Air fryer DIGITAL IZ-8225 IZZY
Voltage: 220~240V
Frequency: 50/60Hz
Power: 2200-2600 W
Capacity: 10Lt

Important Information for Correct Disposal of the Product in Accordance with EC Directive 2002/96/EC

At the end of its working life, the product must not be disposed of as urban waste. It must be taken to a special local authority differentiated waste collection centre or to a dealer providing this service. Disposing of a household appliance separately avoids possible negative consequences for the environment and health deriving from inappropriate disposal and enables the constituent materials to be recovered to obtain significant savings in energy and resources.

As a reminder of the need to dispose of household appliances separately, the product is marked with a crossed-out wheeled dustbin.

Guarantee & Customer Service

BENRUBI Company guarantees its products for any manufacturing defect or defective materials for a period of two (2) years from the date of purchase or delivery by presenting purchase receipt. If your product malfunctions or you find any defects, please revert to the retail location you have purchased it from or contact an authorized BENRUBI Service Centre. To find the nearest authorized BENRUBI Service Centre, visit our website www.benrubi.gr. It is in the discretion of BENRUBI Company to replace or repair the defective product.

The warranty does not cover damages resulting from normal wear, breakage, scaling, improper installation or maintenance of the product, mishandling, abnormal working conditions, failure to implement the instructions, conversion or repair of the product by an unauthorized technician who does not belong to the BENRUBI Service Centers.

Also, the warranty does not cover the following indicative factors:
• Stains, discoloration or scratches.
• Burns due to exposure to heat or flame.
• Damage from thermal shock (sudden temperature change or change of voltage).

FOR MORE INFORMATION PLEASE CONTACT:

(NEW) H. BENRUBI & FILS SA

27 Aghiou Thoma str, GR15124, Maroussi – Athens,
Tel./Customer Support: +30210 6156400
Fax: +302106199316
e-mail: benrubi-sda@benrubi.gr

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>