REGENCY Tables and Sinks Wall Mounted Lockers Instruction Manual
- June 12, 2024
- REGENCY Tables and Sinks
Table of Contents
REGENCY Tables and Sinks Wall Mounted Lockers
Product Information
The Wall Mounted Lockers are a storage solution designed to be mounted on walls. They are made up of various panels, dividers, and hardware for assembly. The lockers come with a back panel, sidepanels, middle dividers, top/bottom panels, a front panel, brackets, blocks, and a coat rod. The package also includes extra bolts and nuts for replacement.
Product Usage Instructions
- Lay out and separate all parts and hardware.
- Align two top/back panels at a 90-degree angle with the panels positioned on the inside of the back panel’s ledge. Use the 3/8 bolts to connect the panels together.
- Repeat Step 2A to connect the second side panel and middle dividers as well as the top panel.
- Place the locker door on top of the panel set and squeeze the nels together so the locker door fits into place and is fully pushed down. Use force if necessary to align all bolt holes properly. Connect the locker doors to side panels and back panels using 3/8 bolts. Bolt the inside of shelving to the locker doorframe.
- Bolt the back panel and top panel together with the block. Bolt the bracket to the side panels and attach the garment rack to the bracket. Secure the garment rod with a hex head bolt. Bolt the inside of shelving to the locker door frame.
- Finish bolting any shelves, side panels, back panels, and extension legs, ensuring that all pieces are securely bolted together. Tighten bolts with a ratchet if necessary.
Optional: There may be additional optional steps or features not mentioned in this manual. For more information, please visit regencytablesandsinks.com.
INCLUDED PARTS
- A (2) Side Panels
- B (3) Middle Dividers
- C (1) Back Panel
- D (2) Top/Bottom Panel
- E (1) Front Panel
- F (2) Bracket
- G (4) Block
- H (1) Coat Rod
- I (4) 3/8″ Bolt for Bracket
- G (74) 1/2″ Bolts
- K (78) Nuts
- L (2) Hex Head Bolts
TOOLS NEEDED
- Wood Plank
- Hammer
- Ratchet and 10mm Socket
ADDITIONAL NOTES:
- If lockers are bent, use a wood block and hammer to reshape.
- Bolts are hand-tighten safe, however, use a ratchet where necessary
- Make note that package includes extra bolts and nuts in case of lost parts
- When fastening bolts, bolt thread faces interior, bolt head faces exterior
ASSEMBLING
ASSEMBLING THE LOCKERS
- Lay out and separate all parts and hardware.
- Align two top/back panels at a 90-degree angle.
- A The panels are to be positioned on the inside of the back panel’s ledge.
- B Use the 3/8″ bolts to connect the panels together.
- C Repeat Step 2A to connect the second side panel and middle dividers as well as the top panel.
- A Place the locker door on top of the panel set and squeeze the panels together so the locker door fits into place and is fully pushed down.
- B Use of force may be required to ensure all bolt holes are aligned properly.
- C Use 3/8” bolts to connect locker doors to side panels and back panels.
- D Inside of shelving will need to be bolted to the locker door frame.
Bolt the back panel and top panel together with the block.
- A Bolt the bracket to the side panels and attach the garment rack to the bracket.
- B Secure the garment rod with hex head bolt.
- C Inside of shelving will need to be bolted to the locker door frame.
Inspect the outside of the locker – front, back, and sides. Finish bolting any shelves, side panels, back panels, and extension legs, ensuring that all pieces are bolted together. Tighten bolts with ratchet if necessary.
OPTIONAL:
- Garmet hooks can be placed where desired.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>