SelectBlinds Zebra Shades Motorized Roller Shades with Cassette Instruction Manual

SelectBlinds Zebra Shades Motorized Roller Shades with Cassette

Product Specifications

• Product Type: Motorized Roller Shades with Cassette
• Control Type: Motorized
• Mounting Options: Top-Fixing, Face-Fixing
• Child Safety Feature: Chain Tensioner

The brackets offer two methods of installation:

1. Top-Fixing: Use the front two holes in the top of the bracket to fix to the lintel (the ‘ceiling’ of the recess).
2. Face-Fixing: Use two screws through the backplate to mount it onto a facing surface (a wall or window frame).

Note that the position of the outermost brackets should be at least 5cm away from the ends of the rail, with any other brackets evenly distributed across the width.

Holding the rail at an angle, situate the T-shaped lip on the top of the cassette into the front lip of the bracket.

Twist the back of the cassette upwards until it snaps into place against the back lip of the bracket.

Installation Guide for Zebra Shades

• Shades with clutch controls come with a continuous chain loop, which should always be screwed to the wall with the included chain tensioner.
• The chain tensioner should be installed to a flat surface, so the bead chain is taut but not stretched. Be sure not to twist or cross the chain.
• On inside mount shades, the tensioner may be attached to the windowsill or to the inside of the window frame. For outside mount or wall mount shades, the bracket may be mounted to the exterior of the window frame or the wall.
• With a pencil, mark the desired location of the screw holes for the tensioner and then drill pilot holes. Then install the tensioner with the screws, making sure that the tensioner is fully installed, so that the spring is pushed in and the chain passes smoothly through the guide.

The chain tensioner forms an important safety function by keeping chain loops away from small children. Never operate this shade without a functioning and correctly installed chain tensioner.

Installation Guide for No-Drill Blinds Headrail

The No-Drill Blinds Headrail will already be installed onto the existing product headrail. Remove the product from the headrail using appropriate methods.

• Preparing: Pull or push to retract the tension boot and install metal strips or adhesive tape on the window opening if needed.
• Installation: Insert the headrail into the window opening, make it flush with the top, and then secure it by extending the tension spring.
• Installing Product: Install product onto brackets and test for secure installation and smooth functionality.

FAQ

• Q: Do I need any special tools for installation?
• A: Basic tools such as a screwdriver, drill, and measuring tape may be required for installation. Please refer to the specific instructions provided with your product for more details.
• Q: How do I reset the motorized roller shades if they are working?
• A: To reset motorized roller shades, locate the reset button on the motor or refer to the user manual for specific instructions on resetting your particular model.

Fitting the brackets

• The brackets offer two methods of installation:

Top-Fixing

• Use the front two holes in the top of the bracket to fix to the lintel (the ‘ceiling’ of the recess).

Face-Fixing

• Use two screws through the back plate to mount onto a facing surface (a wall or window frame)

Note that the position of the outermost brackets should be at least 5cm away from the ends of the rail, with any other brackets evenly distributed across the width.

Fitting the shade

• Holding the rail at an angle, situate the T-shaped lip on the top of the cassette into the front lip of the bracket.
• Twist the back of the cassette upwards until it snaps into place against the back lip of the bracket.

Child Safety

Chain Tensioner

• Shades with clutch controls come with a continuous chain loop, which should always be screwed to the wall with the included chain tensioner.
• The chain tensioner should be installed to a flat surface, so the bead chain is taut but not stretched. Be sure not to twist or cross the chain.
• On inside mount shades, the tensioner may be attached to the windowsill or to the inside of the window frame. For outside mount or wall mount shades, the bracket may be mounted to the exterior of the window frame or the wall.
• With a pencil, mark the desired location of the screw holes for the tensioner and then drill pilot holes. Then install the tensioner with the screws, making sure that the tensioner is fully installed, so that the spring is pushed in and the chain passes smoothly through the guide.
• The chain tensioner forms an important safety function by keeping chain loops away from small children. Never operate this shade without a functioning and correctly installed chain tensioner.
• Please retain these instructions for future reference.
• Thank you for purchasing this product. Please read the instructions and warning carefully before installation to ensure the safe and satisfactory use of this product.

No-Drill Blinds Headrail

• The difficulty level of this installation is ranked at Level 1. A piece of cake!
• If you have questions or get stuck, call our Customer Care Team at 888-257-1840, or email customercare@selectblinds.com

Remove the No-Drill Blinds Headrail

• The No-Drill Blinds Headrail will already be installed onto the existing product headrail.
• Remove the product from the headrail (See Fig A), which will vary from product and depend on lift type.

Preparing the No Drill Blinds Headrail

• Pull the lever from below or push down on the mechanism from above to retract the tension boot (See Fig B).
• Install the metal strips or padded adhesive tape on opposite sides of the window opening where you’ll be installing the No-Drill Blinds Headrail. This is optional and only available on larger products.

Installing the No Drill Blinds Headrail

• Insert the No-Drill Blinds Headrail into the window opening, make it flush with the top of the window opening, then push on the lever to extend the tension spring and secure the No-Drill Blinds Headrail. (See Fig C)

Installing the Product

• Install the product onto the brackets (See Fig D). Test and operate the product to ensure secure installation and smooth functionality.

Uninstalling the No Drill Blinds Headrail

• To uninstall the product, follow step 1 by removing the product from the headrail and use a screwdriver to unlatch the lever.
• Make sure to hold the No Drill Blinds Headrail in place while unlatching the lever. This will prevent damage to the window or headrail.

Tech Tip

• If the fixed boot end was accidentally forced out, use a flathead screwdriver to twist the red “droplets” towards the center and then push it back in.

CONTACT

• Customer Care Team at 888-257-1840, or email customercare@selectblinds.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>