Claude Home Scape Wall Light Instruction Manual

Claude Home Scape Wall Light

Specifications

• Dimensions: W160 H120 D90 MM / W6.3 H4.7 D3.5 IN
• Weight & Material: 1 kg – Aluminium, 2 kg – Brass, 2 kg – Darkened Brass
• Classification: IP20
• Light Source: G9 LED bulb (Incl.) 2.6W, 220-240V
• Lumen: 320lm
• Kelvin Rating: 2700K
• Dimmable: On request 3.5W, IND/ UK/ EU
• Hardware: W146 H55 D22 MM Stainless steel Cord- Hardwire

Care Instructions

Ensure your hands are clean before touching the metal surface to avoid leaving any fingerprint marks. It is advised to use gloves when handling the lighting fixture. Do not use any abrasive substances on the product. Handle with care.
Over time, use metal polish with a soft, dry cloth to retain the original aluminium or brass finish. Avoid using polish on darkened brass finish. Use a dry cloth to remove dust occasionally.

CAUTION

BEFORE INSTALLATION
Please read and understand the provided step-by-step instructions thoroughly before proceeding with the installation. By taking these precautions and diligently following the provided guidelines, you will achieve a secure and successful installation.

1. Always remember to turn off the power supply to the circuit before commencing any installation work. Electrical installation tasks should exclusively be undertaken by an authorized electrical contractor. For professional guidance, please contact your local electricity authority.
2. Before installation, check the installation area for the presence of any other cables to prevent damage to concealed wiring.
3. When positioning the light fixture, ensure that the chosen area can adequately support the weight of light upto 2kg ( 4.5 lbs, aluminium)/ 3kg (6.6 lbs, brass, darkened brass).
4. Please note that this fixture is designed for use in dry domestic indoor environments only.
5. Before installing or changing a G9 bulb, it’s essential to switch off the mains power and allow the lamp to cool.
6. When handling the metal fixture, ensure your hands are clean. It is advised to wear gloves to avoid leaving marks on the metal surface.

CARE INSTRUCTIONS

• Ensure your hands are clean before touching the metal surface to avoid leaving any fingerprint marks. It is advised to use gloves when handling the lighting fixture. Do not use any abrasive substances on the product. Please be wary of its weight. Handle with care.
• Over time, the metal surface may diminish its original luster. To retain the original aluminium or brass finish, use metal polish with a soft, dry cloth and gently rub it onto the surface. Please refrain from using any polish on the darkened brass finish, as this may result in the removal of the patina. Use a dry cloth to remove dust occasionally.

TECHNICAL DETAILS

Dimensions
W160 H120 D90 MM W6.3 H4.7 D3.5 IN

Weight & Material

1. kg – Aluminium
2. kg – Brass
3. kg – Darkened Brass

Classification

• IP20

Light source
IND/ UK/ EU
G9 LED bulb (Incl.)
2.6W, 220-240V

US/ JPN
G9 LED bulb (not incl.) Suggested wattage 2W-5W 110-120V

Lumen
320lm

Kelvin Rating

• 2700K

Dimmable

• On request
• 3.5W, IND/ UK/ EU

Hardware
W146 H55 D22 MM W5.7 H2.2 D0.9 IN Stainless steel Cord – Hardwire

INSIDE THE BOX

NOTE : G9 LED Bulb is not included for regions with voltage requirement 110-120V.

STEP 1

Position and install the Crossbar (B) on junction box (A) Align the crossbar (B) with the junction box’s holes (D), ensuring the arrow (C) on the crossbar points upwards. Secure it in place using the screws (not provided with the fixure as J-boxes can vary). Connect the ground wire (G) to the grounding terminal (GND) on the crossbar (Fig. 1).

STEP 2: Set the position of the Mounting plate (F)

• Use M4 screws with hex nuts (E) to level the mounting plate (F) by tightening them on the crossbar (B) (Fig. 2), ensuring it’s level and flush with the drywall (Fig. 3). Note that drywall thickness affects the space between the crossbar (B) and the mounting plate (F).
• To achieve a seamless mounting, the mounting hardware is hidden behind the drywall. Keep in mind that because the drywall needs time to dry, this installation takes more than a day. Consider hiring a professional drywall expert.

STEP 3: Secure the Mounting plate (F)
Align the arrow (H) on the mounting plate (F) with the arrow (C) on the crossbar (B) and use the M4 screws (I) to secure the mounting plate (F) on the crossbar (B) (Fig. 4).

STEP 4 Conceal the Mounting plate (F)
Use mesh tape and apply mud, sand and paint to match the surrounding surface finish. For best results, hire a drywall professional. Keep in mind that two mounting holes (J & K), one power hole (L), and the electrical wires must remain exposed to complete the installation (Fig. 5).

NOTE : Before proceeding with the installation, unscrew the canopy screws to disassemble the canopy casing with diffuser.

STEP 5
Position and install the Back plate
Pull out the electrical connection point from the canopy back plate (M). Tighten the M4 round head screw (P) on the back plate (M) of the canopy casing.

STEP 6
Connect the wiring
Take the electrical connection and connect both ends of the wire to the wire connector (O) on the back of the top canopy casing (N).

STEP 7: Attach the top Canopy casing
Attach the top canopy casing (N) to the back plate (M) and secure it by tightening the canopy screw (Q) on both ends.

STEP 8: Install the Bulb
Insert the G9 bulb (R) into the bulb holder on the top canopy casing (N). Test the connection and move on to the next step.

STEP 9: Insert the Diffuser
Slide the diffuser (S) into the space between the back plate (M) and the top canopy casing (N).

STEP 10: Secure the Diffuser
Tighten the canopy screw (P) to secure the diffuser (S) in place.

STEP 11: Install the Light
Take the metal light shade (T) and slide the rod into the back plate (M).

STEP 12: Clean the surface
Use a dry cloth to gently wipe the metal surface and remove any fingerprint marks.

1. Use the gloves provided to avoid leaving fingerprint marks on the metal surface.

Frequently Asked Questions

• Q: Is the G9 LED bulb included in the product?
  • A: The G9 LED bulb is included for regions with voltage requirements of 220-240V. For regions requiring 110-120V, the bulb is not included.
• Q: Can the SCAPE WALL LIGHT be used in outdoor environments?
  • A: No, the fixture is designed for use in dry domestic indoor environments only.

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>