F03-0135-0AA1 Atomstack Maker Rotary Chuck Instruction Manual

: June 13, 2024
: ATOMSTACK

Table of Contents

Product Using Installation Instruction
Read User Manual Online (PDF format)
Download This Manual (PDF format)

**F03-0135-0AA1 Atomstack Maker Rotary Chuck Instruction Manual

**

Product Using Installation Instruction

Packing list

Chuck body assembly
Support column assembly
Hexagonal jaws*3PCS L
L-shaped jaws*3PCS
H2.5 Hexagonal Plate Handle*1PCS

H3.0 Hexagonal Plate Handle*1PCS

Screw 3*6mm(6PCS)
Heightened feet *4PCS
Instruction manual

Mini level meter *1PCS
Soft ruler*1PCS
black plug wire*1PCS
White plug wire*1PCS
Caliper*1PCS

Heightening feet installation

When you need to work with the chuck to engrave or cut wide surface objects, you need to install the heightening foot. The laser engraver can be raised to engrave or cut taller objects by installing heightening foot accessories.

Chuck and heightening feet with the use of diagrams

Heightened fee

Connection cable use

The chuck has two connecting wires, black plug and white plug, note that they are wired in a different order and need to be connected carefully.

4PIN white plug cable for connecting ATOMSTACK laser engraving machine.
4PIN black plug cable for connecting to third party laser engraving machine.
The R1 chucking kit supports ATOMSTACK and third party laser cutters and engravers. You need to connect it to the device and use the appropriate software to operate it. If you cannot connect it, please change the order of the wires and change the processing as shown in Figure 1.1-1.2.

White plug wire connection sequence
The connection sequence of black plug wires

Terminal plug for connecting the chuck

|
---|---
Y-axis motor wire plug| Chuck motor plug| Y-axis motor wire plug| Chuck motor plug

White plug cable for Atom stack

|

Black plug wire other brands use

product use introduction

| Product portfolio using accessories| Engraved shapes/items
---|---|---
| Rings (rings and other smaller diameter circles) Circles (larger diameter circles such as bracelets)
| Circles (larger diameter circles such as bracelets)
Cylindrical
Goblets
| Circles (larger diameter circles such as bracelets)
Cylindrical
Goblets
| | Sphere, egg-shaped (curved surface is not obvious), non-invekible
| Sphere, egg-shaped (curved surface is not obvious), non-invekible

Installation guide

Step 1: Direction of chuck rotation
Clockwise for locking, counterclockwise for unlocking
Step 2 (A 1 ) : Installation of L-shaped jaws (method 1)
Key points of operation : the sphere should stick to the three jaws as far as possible, and then The suction cup of the rear support column is attached to the sphere, and then tightened screw. When disassembling the ball, you can put the chuck Loosen, then move the support column back.

Support column assembly

Step 2 (A 1) : Installation of L-shaped jaws (method 2)
Note:

When engraving a curved surface, take the average value of the diameter/circumference of the actual engraving range of the measured object (the average value of the left, middle and right of the engraving range position)
When tilting and engraving, adjust the appropriate position of engraving by rotating the button
Round bottom object engraving

Step 2 (B 1 ) : Installation of step jaws jaws (method 1)
Key points of operation: The sphere should be flattened by the three claws, and then the support column Flatten the sphere with the suction cup, and then tighten the screws. Disassemble the sphere, you can loosen the chuck first, and then move the support back column.
Note:

When engraving a curved surface, take the average value of the diameter/circumference of the actual engraving range of the measured object (the average value of the left, middle and right of the engraving range position)
When tilting and engraving, adjust the appropriate position of engraving by rotating the button
Round bottom object engraving

Support column assembly

Step 2 (B 2) : Installation of step jaws jaws (method 2)
Note:

When engraving a curved surface, take the average value of the diameter/circumference of the actual engraving range of the measured object (the average value of the left, middle and right of the engraving range position)
When tilting and engraving, adjust the appropriate position of engraving by rotating the button
Non-circular bottom object engraving

Step 2 (C 1) : Installation of hexagonal jaws
Key points of operation: when engraving a curved surface, take the measured object Diameter/- circumference average of actual engraving range (engraving The three values on the left, middle and right of the range position are equal mean)
Note:

When tilting and engraving, use the motor rotation button to adjust the appropriate position for engraving.

Support column assembly

Light Burn software use

Add “Start Rotation” to the main window
Click “Settings” on the toolbar
In the settings window, open the “Show rotation in main window to enable” button and click OK
Open the Rotation Settings window and set the parameters
Open the Rotation Settings window: click “Laser Tools” on the toolbar, then click “Rotary Setup”
Set the correct parameters in the rotation setting window: as shown in the figure
Steps:
Select the type of rotation: Chuck
Open “Enable Rotary”
Select “Y-axis” rotation axis
Enter the parameters of the rotating device (fixed value)
Enter your object parameters: the actual measured diameter or circumference of the object to be measured
Import the pattern you want to engrave, set the size of the pattern, and set the power and speed of the engraving.
You can click “Frame” to preview the position of the engraving pattern, and then move the laser head to the desired position.
It is recommended to use “Current Position” for the start position and click “Start” when you have finished setting

Notes

Make sure you have placed the chuck module parallel to the working area of the engraving machine before rotating the engraving. otherwise the pattern engraved on the object may be deformed
Try to make the three contact surfaces of the object under test and the jaw assembly flat
When the sphere needs to be removed after engraving, first loosen the chuck knob and then loosen the bracket fixing knob
Do not forget to update the parameters of the measured object in the rotation setting window every time you change the measured object.
Turn off “Enable Rotary” in the main window when plane engraving, otherwise the engraving pattern will be deformed.
If you are using this product for the first time, please read the accompanying materials carefully to improve your experience. If you do not use the product in accordance with the instructions and requirements or due to mishandling of the product, etc., ATOM STACK shall not be liable for any loss resulting therefrom.
ATOM STACK has carefully checked the contents of the manuals, but there may still be errors or omissions, ATOM STACK is committed to continually improving the functionality of its products and the quality of its services, and therefore reserves the right to change any manuals and the products or software described in the contents of the manuals without prior notice.

Customer service :

For detailed warranty policy, please visit our official website : www.atomstack.net
For technical support and service, please email support@atomstack.net

Manufacturer :

Shenzhen AtomStack Technologies Co.,Ltd

Address :

202, Building 1, Mingliang Technology Park, No. 88 Zhuguang North Road, Taoyuan
Street, Nanshan District, Shenzhen, Guangdong, China
Zip code : 518172

Scan QR code:

QR code reader/barcode scanner or any app with a scanner