FlexStyle HD400 Series Air Styling and Drying System Hair Dryers Instruction Manual
- June 13, 2024
- FlexStyle
Table of Contents
FlexStyle HD400 Series Air Styling and Drying System Hair Dryers
IMPORTANT SAFETY INSTRUCTIONS
When using electrical appliances, especially when children are present, basic safety precautions should always be followed, including the following:
FOR HOUSEHOLD USE ONLY
READ ALL INSTRUCTIONS BEFORE USING—SAVE THESE INSTRUCTIONS
WARNINGS: KEEP AWAY FROM WATER
DANGER—
As with most electrical appliances, electrical parts are electrically live even when the switch is off.
WARNING
To reduce the risk of death by electric shock:
- Always unplug the unit immediately after using.
- Do not use while bathing.
- Do not place or store appliance where it can fall or be pulled into a tub or sink.
- Do not place in or drop into water or other liquid.
- If an appliance falls into water, unplug the unit immediately. Do not reach into the water.
WARNING
To reduce the risk of burns, electrocution, fire, or injury to persons:
- An appliance should never be left unattended when plugged in.
- Close supervision is necessary when this appliance is used by, on, or near children or individuals with certain disabilities.
- Use this appliance only for its intended use as described in this manual. Do not use attachments not recommended by the manufacturer.
- Never operate this appliance if it has a damaged cord or plug, if it is not working properly, or if it has been dropped, damaged, or dropped into water.
- Keep the cord away from heated surfaces.
- Do not wrap the cord around the appliance.
- Never block the air openings of the appliance or place it on a soft surface, such as a bed or couch, where the air openings may be blocked. Keep the air openings free of lint, hair, and the like.
- Never use while sleeping.
- Never drop or insert any object into any opening.
- Do not use outdoors or operate where aerosol (spray) products are being used or where oxygen is being administered.
- Do not use an extension cord with this appliance.
- Do not direct hot air toward eyes or other heat sensitive areas.
- Attachments may be hot during use. Allow them to cool before handling.
- Do not place appliance on any surface while it is operating.
- While using the appliance, keep your hair away from the air inlets.
- Do not operate with a voltage converter.
- Only use the appliance with the voltage, frequency and power shown on the rating label on the product.
- Do not use this appliance on hair extensions or wigs unless recommended by the hair extension or wig manufacturer.
- If hair styling product is being used in conjunction with this appliance please read and follow all of the hair styling product safety warnings and instructions before use.
SAVE THESE INSTRUCTIONS
OPERATING INSTRUCTIONS
- Turn the styler on and off.
- Adjust the airflow. Pressing the button allows you to choose a low, medium, or high airflow.
- Adjust the temperature. Pressing the button allows you to choose no heat, low, medium, or high temperature.
- Press and hold the Cool Shot button for a cool burst of air to set your style.
- To attach any accessories included with your model, press them into the nozzle outlet. You will know they are properly attached when they click in place.
- To remove accessories, slide the lock down and lift the accessory off the nozzle by holding onto the touchpoints identified in your Style Guide.
- To change from styling wand mode to hair dryer mode, slide down the lock and rotate the nozzle left. Keep rotating the nozzle until it clicks into place in hair dryer mode. To change from hair dryer mode to styling wand mode, slide down the lock and rotate the nozzle right.
- To remove the filter cover, slide it off the bottom of the unit. To attach the filter cover, slide it back on to the bottom of the unit until it clicks in place.
- Press the ALCI button to rest the dryer. See Troubleshooting & Error Codes for more information.
- Rating label location.
For further operating instructions, please consult the Styling Guide or scan the QR code.
Storage, Cord Safety, and Maintenance/Cleaning:
- Ensure the cord is not knotted, twisted, or wrapped around any nearby objects when in use.
- Store the unit in a dry location away from water and other heat sources. Store brush accessories so the bristles are not touching any surfaces to help prevent bristle damage.
- Clean the filter at the bottom of the unit monthly. To clean the filter, first slide the filter cover off the bottom of the unit. Then use a new toothbrush to brush off any dust or debris on the filter. Once the filter is clean, slide the filter cover back on the unit until it clicks in place.
- Remove any hair on the brush accessories after every use to help maintain performance.
TROUBLESHOOTING & ERROR CODES
MAINTENANCE/CLEANING
Reduction in Airflow.
Make sure you are not covering the filter cover with your hand when operating the unit. This will block the air inlet, which could cause a reduction in airflow. A change in airflow or air power, airflow blockages, and/ or visible buildup on the inlet at the bottom of the unit could also indicate your unit needs to be cleaned. To maintain performance, clean the filter at the bottom of the unit every month, using a new toothbrush.
ALCI OPERATION
Electricity flickers or trips circuit breaker during use.
This dryer is equipped with an Appliance Leakage Circuit Interrupter (ALCI), a safety feature that renders it inoperable under abnormal conditions. Should the dryer turn off in use, press the red Reset button on the plug and the dryer should function normally. If the dryer does not reset, please check your circuit breaker. If the issue persists, ensure there are no other appliances plugged in within the room where the dryer is being used. Do not use the dryer with a power strip.
OVERHEATING
Hair dryer is overheating or shuts off.
This unit is equipped with a temperature-protective thermostat. If for some reason your hair dryer overheats, the thermostat will automatically turn the unit off. To prevent power-down recurrence, unplug the hair dryer and set it aside to cool, or cool down using the Cool Shot button during use. Overheating may result if the unit is powered on for a long duration, or can indicate a blockage or dust buildup. To prevent overheating, clean the filter at the bottom of the unit every month, using a new toothbrush. Make sure you are not covering the filter with your hand when operating the unit, as this could also cause overheating. If overheating continues to occur, contact Customer Service at 855-522-0912.
TWO (2) YEAR LIMITED WARRANTY
The Two (2) Year Limited Warranty applies to purchases made from authorized
retailers of Shark Ninja Operating LLC.
Warranty coverage applies to the original owner and to the original product
only and is not transferable.
Shark Ninja warrants that the unit shall be free from defects in material and
workmanship for a period of two (2) years from the date of purchase when it is
used under normal household conditions and maintained according to the
requirements outlined in the Owner’s Guide, subject to the following
conditions and exclusions:
What is covered by this warranty?
- The original unit and/or non-wearable parts deemed defective, in Shark Ninja’s sole discretion, will be repaired or replaced up to two (2) years from the original purchase date.
- In the event a replacement unit is issued, the warranty coverage ends six (6) months following the receipt date of the replacement unit or the remainder of the existing warranty, whichever is later. Shark Ninja reserves the right to replace the unit with one of equal or greater value.
What is not covered by this warranty?
- Normal wear and tear of wearable parts (such as accessories), which require regular maintenance and/or replacement to ensure the proper functioning of your unit, are not covered by this warranty. Replacement parts are available for purchase at sharkclean.com.
- Any unit that has been tampered with or used for commercial purposes.
- Damage caused by misuse, abuse, negligent handling, failure to perform required maintenance (e.g., failure to keep the well of the motor base clear of food spills and other debris), or damage due to mishandling in transit.
- Consequential and incidental damages.
- Defects caused by repair persons not authorized by Shark Ninja. These defects include damages caused in the process of shipping, altering, or repairing the Shark Ninja product (or any of its parts) when the repair is performed by a repair person not authorized by Shark Ninja.
- Products purchased, used, or operated outside North America.
How to get service
If your appliance fails to operate properly while in use under normal
household conditions within the warranty period, visit
sharkbeauty.com for product care and maintenance
self-help.
Our Customer Service Specialists are also available at
855-522-0912 to assist with product
support and warranty service options, including the possibility of upgrading
to our VIP warranty service options for select product categories. So we may
better assist you, please register your product online at
registeryourshark.com and have the product on
hand when you call.
Shark Ninja will cover the cost for the customer to send in the unit to us for repair or replacement. A fee of $20.95 (subject to change) will be charged when Shark Ninja ships the repaired or replacement unit.
How to initiate a warranty claim
You must call 855-522-0912 to initiate a warranty claim. You will need the receipt as proof of purchase. We also ask that you register your product online at registeryourshark.com and have the product on hand when you call, so we may better assist you. A Customer Service Specialist will provide you with return and packing instruction information.
How state law applies
This warranty gives you specific legal rights, and you also may have other rights that vary from state to state. Some states do not permit the exclusion or limitation of incidental or consequential damages, so the above may not apply to you.
FCC WARNINGS
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to parts 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if
not installed and accordance with the instructions, may cause harmful
interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device complies with part 15 of the FCC rules.
Operation is subject to the following conditions:
- This device may not cause harmful interference.
- This device must accept any interference received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this device.
ISED Statement
This device complies with Industry Canada license-exempt RSS standard(s).
Operation is subject to the following two conditions:
(1) this device may not cause interference, and (2) this device must accept
any interference, including interference that may cause undesired operation of
the device.
CUSTOMER SUPPORT
For accessories and replacement
parts,
visit sharkclean.com/accessories
SCAN QR CODE FOR FULL
INSTRUCTIONS, WARRANTY
INFORMATION, AND HOW-TOS
© 2022 Shark Ninja Operating LLC. SHARK FLEXSTYLE is a trademark of Shark
Ninja Operating LLC.
HD400_Series_Warning_Insert_E_F_S_REV_Mv2
If you are experiencing a different error code,
please scan the QR code for additional troubleshooting
or contact Customer Service at
855-522-0912.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>