evenflo Easy Walk-Thru Clear Gate Instruction Manual

: June 12, 2024
: evenflo

Table of Contents

Safety
Parts List
Assemble Gate
Gate Operation
Care and Maintenance
Limited Warranty
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

evenflo Easy Walk-Thru Clear Gate Instruction Manual

Safety

WARNING
Children have died or been seriously injured when gates are not securely installed.

ALWAYS install and use gate as directed using all required parts.
NEVER use with a child or pet able to climb over, dislodge or open the gate.
NEVER leave child unattended.
NEVER use to keep child away from pool.
You MUST install Mounting Caps to keep gate in place. Without Mounting Caps, child can push out and escape.
To prevent falls, NEVER use at the top of the stairs.
Intended for use ONLY with children 6 months through 24 months.
To ensure proper fit, use ONLY in openings between 76 – 82.5 cm (30 – 32.5 in) and 89 – 95 cm (35 – 37.5 in) wide.
To help prevent entrapment, DO NOT allow space between bottom of gate and floor to exceed 7.62 cm (3 in).
Use ONLY with locking/latching mechanism securely engaged.
To help prevent gate from dislodging, make sure all four Adjustment Bumpers fit securely in the Mounting Caps against wall or doorway opening.
To prevent falls, DO NOT attempt to step over gate.
STOP using gate if parts are missing or if gate becomes damaged, broken, or disassembled.
Use in doorways with wooden frames. When installing against drywall, ensure mounting surface is reinforced with a wall stud to help prevent damage.
Periodically check all fasteners to be sure they are tight and secure to prevent gate from dislodging.
Pressure-mounted gates may dislodge if significant pressure is placed against them. Avoid applying significant pressure or weight.
This gate will NOT necessarily prevent all accidents.
For indoor use ONLY.
STRANGULATION HAZARD – Pets can force themselves into very small openings. Use this gate only with pets whose head or body WILL NOT fit into openings in the gate, between the gate and the floor, or between the gate and the wall.
Ensure gaps between the safety gate and the side of the door frame are approximately equal. NEVER exceed 5 cm (2 in).
Ensure child is kept away from the gate when closing or opening it to prevent injury to the child, such as from pinching.

Important Information

IMPORTANT: Failure to follow installation instructions could result in serious injury to your child. Read these instructions completely and keep for future reference.

Parts List

If you are missing parts, do not use gate. Visit us at www.evenflo.com, or call Evenflo ParentLink at 1-800-233-5921 (U.S.A.), 1-937-773-3971 (Canada), or 800-706-1200 (Mexico) to order replacement parts.

Parts List

Registration Information: Please register this product so we can reach you if there is a safety alert or recall. We will not sell, rent, or share your personal information. To register your product, please complete and mail the card that came with it or visit our on-line registration at www.evenflo.com/registerproduct

For future reference, record the Model Number and Date of Manufacture below.

Model Number: Date of Manufacture:

Assemble Gate

WARNING
DO NOT remove YELLOW TAG or PLASTIC
TIES at this time or serious injury may result.

Measure and record the width of the opening where you will use the gate.
If the opening width is 89 – 95 cm (35 – 37.5 in), install extension A on the gate frame B, as shown. Make sure the plastic caps on the extension A and the gate B touch each other. The plastic caps MUST touch each other to securely install the extension.
NOTE: Extension can be installed on either side of gate.
Push four Adjustment Bumpers C onto the corners of the gate frame B or the gate extension.
NOTE: Make sure the Adjustment Bumpers are pushed all the way in.
Position gate B on floor in center of opening, making sure that it is straight up and down (90º to the floor).
NOTE: Rubber ends of adjustment bumpers (D,E) may mark some mounting surfaces.
Peel backing off one side of Adhesive Mounting Pad K. Adhere pad to outside of Mounting Cap L, as shown.
Peel backing off other side of Adhesive Mounting Pad, and place Mounting Cap over end of Adjustment Bumper C.
NOTE: Make sure gate stays straight up and down (90º to floor) and in center of door frame during this process.
Slide Adjustment Bumper C out of gate frame toward door frame, until Mounting Cap sticks to door frame. Repeat this for other three Mounting Caps.

OPTIONAL: If mounting to drywall, mark center of mounting caps.
Pull mounting caps off wall. Drill holes and insert wall anchors. Secure mounting caps with screws. Tighten all four screws securely with handheld Phillips screwdriver, but do not overtighten.
Using the wrench, turn both upper Adjustment Bumpers D and both lower Adjustment Bumpers E, as shown, until all four rubber ends contact the mounting caps.
Check that the gate is still straight up and down then turn each bumper two more full rotations or until tight.
Test to make sure the gate frame assembly is secure by firmly shaking it. If it moves, it needs to be re-installed. Repeat steps 5 – 6.

WARNING
BEFORE removing the YELLOW TAG and cutting the PLASTIC TIES, ENSURE the gate is securely in place or serious injury may result.
With your gate securely in place, remove the yellow tag then cut and discard the plastic ties.

WARNING
Distance between gate frame and door frame should be equal on both sides, and NEVER exceed 5 cm (2 in).
Adjust both upper bumpers D until the gap between the button Fand latch G is 3.2 mm (1/8”).
Inspect the gate door. Make sure it swings freely and latches securely.

Gate Operation

To open gate, slide button H while lifting gate door slightly I and swing the gate open.
When window J is red, gate is NOT latched.
To close gate, push door gently

Care and Maintenance

Wash gate with mild soap and warm water and dry thoroughly before using.
Metal and plastic parts can be wiped clean with a soft damp cloth and dried with a soft cloth. DO NOT use abrasive cleaners or solvents.
Remember to clean rubber ends of adjustment bumpers with rubbing alcohol before each use.

Limited Warranty

For a period of 90 days from the original purchase of this Product, Evenflo warrants to the original end user (“Purchaser”) this Product (including any accessories) against defects in material or workmanship. Evenflo’s sole obligation under this express limited warranty shall be, at Evenflo’s option, to repair or replace any Product that is determined to be defective by Evenflo and determined to be covered by this warranty.

Repair or replacement as provided under this warranty is the exclusive remedy of the Purchaser. Proof of purchase in the form of a receipted invoice or bill of sale evidencing that the Product is within the warranty period must be presented to obtain warranty service. This express limited warranty is extended by Evenflo ONLY to the original Purchaser of the Product and is not assignable or transferable to subsequent purchasers or end users of the Product. For warranty service, contact Evenflo’s ParentLink Consumer Resource Center at 800-233-5921 or www.evenflo.com.

EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ON THIS PRODUCT IS HEREBY DISCLAIMED. EVENFLO SHALL NOT BE LIABLE FOR ANY INCIDENTAL, CONSEQUENTIAL, SPECIAL OR PUNITIVE DAMAGES OF ANY KIND FOR BREACH OF THE EXPRESS LIMITED WARRANTY ON THIS PRODUCT, OR ANY WARRANTY IMPLIED BY OPERATION OF LAW.
OTHER THAN THE EXPRESS LIMITED WARRANTY SET FORTH ABOVE, THERE ARE NO OTHER WARRANTIES THAT ACCOMPANY THIS PRODUCT, AND ANY ORAL, WRITTEN OR ANY OTHER EXPRESS REPRESENTATION OF ANY KIND IS HEREBY DISCLAIMED.

ParentLink
answers. advice. affirmation.-
www.evenflo.com • USA: 1-800-233-5921, 8 AM — 5 PM EST
• Canada: 1-937-773-3971 • Mexico: 800-706-1200

Company Logo