BRESSER F005101 LED Pocket Light Instruction Manual

: June 13, 2024
: BRESSER

Table of Contents

BRESSER F005101 LED Pocket Light
WARRANTY
GENERAL WARNINGS
PARTS OVERVIEW
PARTS DESCRIPTION
CHARGING & POWER SUPPLY
TURNING ON/OFF THE LIGHT
FUNCTIONS & OPERATION
CE DECLARATION OF CONFORMITY
WARRANTY & SERVICE
TECHNICAL DATA
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

BRESSER F005101 LED Pocket Light

Visit our website via the following QR Code or web link to find further information on this product or the available translations of these instructions.

www.bresser.de/PF005101

WARRANTY

www.bresser.de/warranty_terms

GENERAL WARNINGS

DANGER OF BODILY INJURY!
Do not use it in the presence of children or animals. Store out of reach of children and animals.

RISK OF MATERIAL DAMAGE!
Make sure that no one can trip over the connection cables of the device. The device could be knocked over. Only use the recommended power cable or the recommended battery for the power supply! The manufacturer accepts no liability for voltage damage caused by the use of an unsuitable power supply!

DANGER OF AN ELECTRIC SHOCK!
This device contains electronic parts that are powered by a power source (power adapter). Only use the device as described in the manual. Otherwise, you run the DANGER of an ELECTRIC SHOCK. Never bend, squeeze, or pull power cables, connecting cables, extensions, or connectors. Protect cables from sharp edges and heat. Check this device, cables, and connections for damage before use. Never attempt to operate a damaged device or a device with damaged electrical parts! Damaged parts must be replaced immediately by an authorized service agent. Operate the device only in a completely dry environment and do not touch the device with wet body parts.

RISK OF GLARE!

Make sure that people and animals do not look into the light. The high luminosity can cause glare to the eyes and afterimages. This impairment of vision can lead to accidents.

FIRE/EXPLOSION HAZARD!
Always place the device in such a way that it cannot tip over and ensure that it is stored in a reasonably safe place.

Keep children and animals away from the device! They could knock the device over.
Make sure that no one trips over connection cables. The device could be knocked over.
Do not expose the device to high temperatures. Do not short-circuit the device or dispose of it in a fire! Excessive heat and improper handling can cause short circuits, fires, and even explosions!
Only use the recommended power supply*!

IMPORTANT NOTE!
Do not disassemble the device! In the event of a defect, please contact your dealer. They will contact the Service Center and can arrange the return of this device for repair if necessary. Disconnect the power supply by pulling the mains plug when the appliance is not in use, in case of a longer interruption of operation, and before any maintenance and cleaning work. Place your device so it can be disconnected from the power supply at any time. The power outlet should always be near your appliance and should be easily accessible, as the plug of the power cord serves as a disconnect device from the main supply. To disconnect the unit from the mains, always pull the mains plug and never pull the cable! Do not subject the device to excessive vibrations!

PARTS OVERVIEW

PARTS DESCRIPTION

Hole for hand strap
LED-Screen
USB-C Power input socket
USB-A Power Output
Mode button
Battery status indicator
On/Off switch
Dial control
LED lught surface
Connection thread (1/4″ – 20)

CHARGING & POWER SUPPLY

This device is equipped with a rechargeable battery and can therefore be used with or without a mains power supply. Furthermore, you can use it as a power bank to charge your third-party devices (power input: 5V/2A).

Charging the battery

Note: An additional USB-A/USB-C charging cable and a USB power adapter (5V/2A) are required. Read the chapter “Technical data” for detailed information.

Insert the USB-C plug of the charging cable into the USB-C power input socket (3).
Insert the USB-A plug of the cable into the USB-A power socket of the USB power adapter.
Insert the mains plug of the power adapter into a mains power socket (210-230V).
After a successful connection, the battery status indicator (6) lights up green. Its color will change to blue when it is fully charged. The light is ready is for use.

Hint: Use the USB-A power output socket (4) to connect your smart device and charge it via a USB-A/USB-C charging cable* (power bank function).

Mains power supply
Once the battery level low is low, just connect the light with the mains power supply again as mentioned above to enable a direct power supply. The light can be set in operation directly and the battery is charged in parallel.

TURNING ON/OFF THE LIGHT

To turn on the light, slide the On/Off Switch (7) to position “ON”. The light will turn on immediately with settings used latest.
To turn off the light, slide the On/Off switch (7) to position “OFF”. The light will turn off immediately.

FUNCTIONS & OPERATION

CCT / HSI / FX Mode
Shortly press the Mode button (5) to switch between HSI, CCT or FX mode.

In [HSI] mode (RGB color), press the dial control (8) to switch between [INT] (intensity), [Hue] and [SAT] (saturation). Push the dial control up or down to increase or decrease the values.
In [CCT] mode (bi-color), press the dial control (8) to switch between [color temperature] and [intensity control]. Push the dial control up or down to increase or decrease the values.
In special [FX] mode (special effects), press the dial control (8) to switch between [intensity] and [special effect options]. Select [intensity control] and push the dial control up or down to increase or decrease the brightness. Select [special effect options] and push the dial control up or down to select one of the available special effects (see list below).

Special effects list
F1: Fire / F2: Cop car / F3: pulsing / F4: Party / F5: Lightning / F6: TV / F7: Fault bulb / F8: Firework / F9: Paparazzi

*ATTACHING TO OTHER DEVICES (optional)*
Through the two connection threads (10), this LED light can be attached to many other devices such as (D)SLR cameras, camcorders, selfie sticks, gimbals or action cams. An additional adapter* may be required for installation.

DISPOSAL

Dispose of the packaging materials properly, according to their type, such as paper or cardboard. Contact your local waste-disposal service or environmental authority for information on the proper disposal.
Do not dispose of electronic devices in the household garbage! As per the Directive 2012/19/EC of the European Parliament on waste electrical and electronic equipment and its adaptation into German law, used electronic devices must be collected separately and recycled in an environmentally friendly manner.
Under the regulations concerning batteries and rechargeable batteries, disposing of them in normal household waste is explicitly forbidden. Please make sure to dispose of your used batteries as required by law — at a local collection point or in the retail market. Disposal of domestic waste violates the Battery Directive.

CE DECLARATION OF CONFORMITY

Bresser GmbH has issued a „Declaration of Conformity“per applicable guidelines and corresponding standards. The full text of the CE declaration of conformity is available at the following internet address: www.bresser.de/download/BR- RGB/CE/F005101_CE.pdf

WARRANTY & SERVICE

The regular warranty period is 2 years and begins on the day of purchase. To benefit from an extended voluntary warranty period as stated on the gift box, registration on our website is required. You can consult the full warranty terms as well as information on extending the warranty period and details of our services at www.bresser.de/warranty_terms.

www.bresser.de/warranty_terms

TECHNICAL DATA

Model No.	BR-96RGB
Art. No.	F005101
Power Consumption	9W
Luminous Flux	800 lm
Color Temperature	2800K to 6500K
CRI	≥ 95
Dimmer	0% to 100%
Saturation	0% to 100%
Light source	LED; 0.5W28 pcs. @6500K / 0.5W28 pcs. @2800K / 1.5W RGB LEDs

Please contact the service center first for any questions regarding the product or claims, preferably by e-mail.

E-Mail: service@bresseruk.com
*Telephone:** +44 1342 837 098

BRESSER UK Ltd.
Suite 3G, Eden House Enterprise Way Edenbridge, Kent TN8 6HF Great Britain

Number charged at local rates in the UK (the amount you will be charged per phone call will depend on the tariff of your phone provider); calls from abroad will involve higher costs.

Bresser GmbH