Trimble EM130 Empower Module User Guide
- June 3, 2024
- Trimble
Table of Contents
- Trimble EM130 Empower Module
- Safety
- Recycling in Europe
- Components and accessories
- Federal Communication Commission Interference Statement
- Limited Warranty Terms and Conditions
- Limitation of Liability
- Product specifications
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
Trimble EM130 Empower Module
Geospatial Division
- 10368 Westmoor Drive
- Westminster, Colorado 80021 USA
Mobile Computing Solutions
- 345 Avery Ave
- Corvallis, OR 97333
Trimble, Inc. (was Kellenberger, Dayton- both exist)
- 4450 Gibson Dr
- Tipp City OH 45371 USA
Trimble TEBV UK
- 1 Bath Street
- Ipswich, Suffolk IP2 8SD
- United Kingdom
Trimble AB Europe
- Box 64, SE-182 11
- Danderyd, Sweden
Trimble Europe B.V.
- Industrieweg 187A, 5683 CC
- Best, Netherlands
Global technical support
To request detailed technical assistance for Trimble solutions, contact:
trimble_support@trimble.com
Copyright and Trademarks
© 2020-2020, Trimble Inc. All rights reserved. Trimble and the Globe &
Triangle logo and Access are trademarks of Trimble Inc., registered in the
United States and in other countries. Microsoft and Windows are either
registered trademarks or trademarks of Microsoft Corporation in the United
States and/or other countries. The Bluetooth word mark and logos are owned by
the Bluetooth SIG, Inc. and any use of such marks by Trimble Inc. is under
license. All other trademarks are the property of their respective owners.
Manufacturer’s Name: Trimble Inc.
- Manufacturer’s Address: 4408 Gibson Dr, Tipp City, OH 45371
Declares, under our sole responsibility, that the product:
- Model Number(s): 123655
- Spectrum and maximum power: WiFi Halow 802.11ah 23dBm
Product Antenna and Gain
List of antenna information | Gain |
---|---|
Components | Frequency (MHz) |
WLAN | 902-928 |
Safety
- Power requirement
- I/O module connector
- DC power Input 5V, Current 1.5A
- Operating ambient temperature Max: 40˚C
Power supply safety
WARNING – Use only AC and vehicle adapters intended for the device. Other
external power sources may damage your product and void the warranty.
- Ensure the input voltage on the adapter matches the voltage in your location. Ensure the adapter has prongs compatible with your outlets.
- The AC power supply is designed for indoor use only. Avoid using the AC power supply in wet areas.
- Unplug the power supply from power when not in use.
- Do not short the output connector.
Service safety
WARNING
Do not attempt to take apart, open, service, or modify the product,
accessories, or power supply. Doing so could present the risk of electric
shock or other hazard. Any evidence of any attempt to open and/or modify this
device, including any peeling, puncturing, or removal of any of the labels,
will void the Limited Warranty.
Safe environments of use
WARNING
Areas with potentially explosive atmospheres are often, but not always, posted
and can include fueling areas, such as below decks on boats, fuel or chemical
transfer or storage facilities, or areas where the air contains chemicals or
particles, such as grain dust, or metal powders. When you are in such an area,
turn off your device, and do not remove or install battery chargers, AC
adapters, or any other accessories. In such areas, sparks can occur and cause
an explosion or fire.
Distraction
WARNING
Using the device in some circumstances can distract you and may cause a
dangerous situation. Observe rules that prohibit or restrict the use of
devices (for example, avoid operating the device while driving a vehicle).
Recycling information
You should dispose of this product and accessories properly according to local
laws and regulations. Because this product contains electronic components, it
must be disposed of separately from household waste. When the product reaches
its end of life, contact your local Trimble reseller to learn about disposal
and recycling options for your area.
Recycling in Europe
The symbol at right means that according to local laws and regulations your product and/or its battery shall be disposed of separately from household waste. When this product reaches its end of life, take it to a collection point designated by local authorities. The separate collection and recycling of your product and/or its battery at the time of disposal will help conserve natural resources and ensure that it is recycled in a manner that protects human health and the environment.
For Information about recycling Trimble WEEE (Waste Electrical and Electronic Equipment) products that run on electrical power go to http://www.trimble.com/Corporate/Environmental_Compliance.aspx.
To recycle Trimble WEEE products call +31 497 53 24 30, and ask for the “WEEE
Associate”. or mail a request for recycling instructions to: Trimble Europe
B.V. & Trimble InternationalB.V.
Industrieweg 187a 5683 CC Best The Netherlands
Regional compliance
Australia and New Zealand
This product conforms with the regulatory requirements of the Australian
Communications and Media Authority (ACMA) Telecommunications,
Radiocommunications and EMC Labelling Notices, thus satisfying the
requirements for RCM marking and sale within Australia and New Zealand.
Europe
This device complies with Directive 2014/53/EU (RED) issued by the
Commission of the European Community. A minimum separation distance of 20cm
must be maintained between the user’s body and the device.
This Trimble product has been tested and found to comply with all requirements for CE Marking and sale within the European Economic Area (EEA ). The device has Bluetooth and wireless LAN approval and satisfies the requirements for Radio and Telecommunication Terminal Equipment specified by European Council Directive 1999/5/ EC. These requirements provide reasonable protection against harmful interference when the equipment is operated appropriately in a residential or commercial environment.
Frequency bands and Powers
- Frequency band(s) in which the radio equipment operates; Please see the above table in ”Product Antenna and Gain”
- Maximum radio-frequency power transmitted in the frequency band(s) in which the radio equipment operates; Please see the above table in ”Product Antenna and Gain”
Components and accessories
Accessories and components including software that allow the radio equipment to operate as intended. Manufacturers only have to describe those accessories and components including software if they:
- have an influence on the conformity of the radio equipment, and
- are intended to be installed or changed by the user without the control of the manufacturer.
The instructions shall also include the information required as above.
Accessories example:
If the radio equipment is delivered without an antenna, then the technical
features of the antenna that may be used in conjunction with the radio
equipment shall be provided to the user. This information could be the generic
characteristics of a given antenna type or a reference to a specific
antenna(s) available on the market.
CAUTION
Only approved accessories may be used with this equipment. In general, all
cables must be high quality, shielded, correctly terminated and normally
restricted to two meters in length. Power supplies approved for this product
employ special provisions to avoid radio interference and should not be
altered or substituted. Unapproved modifications or operations beyond or in
conflict with these instructions for use may void authorization by the
authorities to operate the equipment.
European declaration of conformity
In all cases assessment of the final product is in compliance with the
Essential Requirements of the RED Directive 2014/53/EU LVD 2014/35/EU EMC
2014/53/EU RED Articles 3.1(a) and (b), safety and EMC respectively, as well
as any relevant Article 3.2 requirements. An up-to-date DoC is available upon
request or can be found at Trimble.com.
Importer of Record
- Trimble European Regional Fulfillment Center Logistics Manager
- Trimble Europe B.V. & Trimble International B.V. industrieweg 187a 5683 CC Best, The Netherlands
Importer of Record
- Trimble European Regional Fulfillment Center Logistics Manager Trimble Europe B.V. & Trimble International B.V.
- Industrieweg 187a 5683 CC Best The Netherlands.
Trimble EC
Trimble Germany Am Prime Parc 11 65479 Raunheim Germany
CAUTION:
Only approved accessories may be used with this equipment. In general, all
cables must be high quality, shielded, correctly terminated and normally
restricted to two meters in length. Power supplies approved for this product
employ special provisions to avoid radio interference and should not be
altered or substituted. Unapproved modifications or operations beyond or in
conflict with these instructions for use may void authorization by the
authorities to operate the equipment.
Recycling information
You should dispose of the device and accessories properly according to local
laws and regulations. Because the device contains electronic components, it
must be disposed of separately from household waste. When the device reaches
its end of life, contact your local Trimble reseller to learn about disposal
and recycling options for your area.
Recycling in Europe
The symbol above means that according to local laws and regulations your
product and/or its battery shall be disposed of separately from household
waste. When this product reaches its end of life, take it to a collection
point designated by local authorities. The separate collection and recycling
of your product and/or its battery at the time of disposal will help conserve
natural resources and ensure that it is recycled in a manner that protects
human health and the environment.
For information about recycling Trimble WEEE (Waste Electrical and Electronic
Equipment) products that run on electrical power go to
http://www.trimble.com/corporate/about_WEEE_ROHS_initiatives.aspx.
To recycle Trimble WEEE products call +31 497 53 24 30, and ask for the “WEEE Associate”. or mail a request for recycling instructions to:
Trimble Europe B.V. & Trimble International B.V.
Industrieweg 187a 5683 CC Best The Netherlands
Canada
IC: 5817A-123655
This radio transmitter has been approved by Industry Canada to operate with
the antenna types listed below with the maximum permissible gain indicated.
Antenna types not included in this list, having a gain greater than the
maximum gain indicated for that type, are strictly prohibited for use with
this device. Cet émetteur radio (identifier l’appareil par numéro de
certification) a été approuvé par l’industrie Canada pour fonctionner avec les
types d’antenne énumérés ci-dessous avec le gain maximum admissible indiqué.
Types d’antennes non inclus dans cette liste, ayant un gain supérieur au gain
maximum indiqué pour cette type, sont strictement interdits pour une
utilisation avec cet appareil.
Industry Canada statement
- This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: 1) this device may not cause interference, and 2) this device must accept any interference, including interference that may cause undesired operation of the device.
- This Class B digital apparatus complies with Canadian ICES-003
- This device complies with RSS-310 of Industry Canada. Operation is subject to the condition that this device does not cause harmful interference.
- This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter, except tested built-in radios.
- The County Code Selection feature is disabled for products marketed in the U.S./ Canada.
This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparel at us as set out in the radio interference regulations of the Canadian Department of Communications.
License exempt
This device complies with Industry Canada license-exempt RSS standard(s).
Operation is subject to the following two conditions:
- This device may not cause interference, and
- This device must accept any interference, including interference that may cause undesired operation of the device.
This Class B digital apparatus complies with Canadian ICES-003.
This Category II radio communication device complies with Industry Canada Standard RSS -310.
Detachable Antenna Usage
This radio transmitter (IC: 5817A-123655 ) has been approved by ISED to
operate with the antenna type listed below with the maximum permissible gain
indicated. Antenna types not included in this list, having a gain greater than
the maximum gain indicated for that type, are strictly prohibited for use with
this device.
List of antenna information | Gain |
---|---|
Components | Frequency (MHz) |
Dipole Antenna | 902-928 |
2dBi
IC SAR warning
Radio Frequency (RF) Exposure Information
The information in this section applies to 121655 wireless products that are
not intended to be operated close to the human body.
The product complies with IC radiation exposure limits set forth for an uncontrolled environment when installed and operated with a minimum distance of 20cm between the radiator and your body.
U.S.
FCC ID: S9E-123655
Federal Communication Commission Interference Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help.
FCC Caution:
- Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.
- This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
For Mobile Device USAGE ( >20cm/low power)
Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance 20cm between the radiator & your body.
FOR COUNTRY-CODE SELECTION USAGE (WLAN DEVICES)
Note:
The country code selection is for non-U.S. models only and is not available to
all U.S. models. Per FCC regulation, all Wi-Fi products marketed in the U.S.
must be fixed to U.S. operation channels only.
Limited Warranty Terms and Conditions
Product Limited Warranty
Subject to the terms and conditions set forth herein, Trimble Inc. (“Trimble”)
warrants that for a period of two (2) years from date of purchase this Trimble
product (the “Product”) will substantially conform to Trimble’s publicly
available specifications for the Product and that the hardware and any storage
media components of the Product will be substantially free from defects in
materials and workmanship.
Product Software
Product software, whether built into hardware circuitry as firmware, provided
as a standalone computer software product, embedded in flash memory, or stored
on magnetic or other media, is licensed solely for use with or as an integral
part of the Product and is not sold. The terms of the end-user license
agreement, as included below, govern the use of the Product Software,
including any differing limited warranty terms, exclusions, and limitations,
which shall control the terms and conditions set forth in the limited Product
warranty.
Warranty Remedies
If the Trimble Product fails during the warranty period for reasons covered by
this limited warranty and you notify Trimble of such failure during the
warranty period, Trimble will repair OR replace the non-conforming Product
with new, equivalent to new, or reconditioned parts or Product, OR refund the
Product purchase price paid by you, at Trimble’s option, upon your return of
the Product in accordance with Trimble’s product return procedures then in
effect.
How to Obtain Warranty Service
To obtain warranty service for the Product, it is recommended you contact your
Trimble dealer. Alternatively, you may contact Trimble to request warranty
service by emailing
Repair_Services@Trimble.com. Please be
prepared to provide: – your name, address, and telephone numbers;
- product name, part number, and serial number;
- proof of purchase;
- an explanation of the problem.
The customer service representative may need additional information from you depending on the nature of the problem.
Warranty Exclusions and Disclaimer
This Product limited warranty shall only apply in the event and to the extent that (i) the Product is properly and correctly installed, configured, interfaced, maintained, stored, and operated in accordance with Trimble’s applicable operator’s manual and specifications, and; (ii) the Product is not modified or misused. This Product limited warranty shall not apply to, and Trimble shall not be responsible for, defects or performance problems resulting from (i) the combination or utilization of the Product with hardware or software products, information, data, systems, interfaces, or devices not made, supplied, or specified by Trimble; (ii) the operation of the Product under any specification other than, or in addition to, Trimble’s standard specifications for its products; (iii) the unauthorized installation, modification, or use of the Product; (iv) damage caused by: accident, lightning or other electrical discharge, fresh or saltwater immersion or spray (outside of Product specifications); or exposure to environmental conditions for which the Product is not intended; (v) normal wear and tear on consumable parts (e.g., batteries); or(vi) cosmetic damage. Trimble does not warrant or guarantee the results obtained through the use of the Product or Software, or that software components will operate error-free.
NOTICE REGARDING PRODUCTS EQUIPPED WITH TECHNOLOGY CAPABLE OF TRACKING SATELLITE SIGNALS FROM SATELLITE-BASED AUGMENTATION SYSTEMS (SBAS) (WAAS, EGNOS, GAGAN, MSAS, AND LUCH), OMNISTAR, BEIDOU, GPS, GALILEO OR GLONASS SATELLITES, OR FROM IALA BEACON SOURCES: TRIMBLE IS NOT RESPONSIBLE FOR THE OPERATION OR FAILURE OF OPERATION OF ANY SATELLITE-BASED POSITIONING SYSTEM OR THE AVAILABILITY OF ANY SATELLITE-BASED POSITIONING SIGNALS.
THE FOREGOING LIMITED WARRANTY TERMS STATE TRIMBLE’S ENTIRE LIABILITY, AND YOUR EXCLUSIVE REMEDIES, RELATING TO THE TRIMBLE PRODUCT. EXCEPT AS OTHERWISE EXPRESSLY PROVIDED HEREIN, THE PRODUCT, AND ACCOMPANYING DOCUMENTATION AND MATERIALS ARE PROVIDED “AS-IS” AND WITHOUT EXPRESS OR IMPLIED WARRANTY OF ANY KIND, BY EITHER TRIMBLE OR ANYONE WHO HAS BEEN INVOLVED IN ITS CREATION, PRODUCTION, INSTALLATION, OR DISTRIBUTION, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, TITLE, AND NON INFRINGEMENT. THE STATED EXPRESS WARRANTIES ARE IN LIEU OF ALL OBLIGATIONS OR LIABILITIES ON THE PART OF TRIMBLE ARISING OUT OF, OR IN CONNECTION WITH, ANY PRODUCT. BECAUSE SOME STATES AND JURISDICTIONS DO NOT ALLOW LIMITATIONS ON DURATION OR THE EXCLUSION OF AN IMPLIED WARRANTY, THE ABOVE LIMITATION MAY NOT APPLY TO YOU.
Limitation of Liability
TRIMBLE’S ENTIRE LIABILITY UNDER ANY PROVISION HEREIN SHALL BE LIMITED TO THE AMOUNT PAID BY YOU FOR THE PRODUCT. TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, IN NO EVENT SHALL TRIMBLE OR ITS SUPPLIERS BE LIABLE FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGE WHATSOEVER UNDER ANY CIRCUMSTANCE OR LEGAL THEORY RELATING IN ANY WAY TO THE PRODUCTS, SOFTWARE, AND ACCOMPANYING DOCUMENTATION AND MATERIALS, (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF BUSINESS PROFITS, BUSINESS INTERRUPTION, LOSS OF DATA, OR ANY OTHER PECUNIARY LOSS), REGARDLESS OF WHETHER TRIMBLE HAS BEEN ADVISED OF THE POSSIBILITY OF ANY SUCH LOSS AND REGARDLESS OF THE COURSE OF DEALING WHICH DEVELOPS OR HAS DEVELOPED BETWEEN YOU AND TRIMBLE. BECAUSE SOME STATES AND JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR LIMITATION OF LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES, THE ABOVE LIMITATION MAY NOT APPLY TO YOU.
NOTE:
THE ABOVE TRIMBLE LIMITED WARRANTY PROVISIONS WILL NOT APPLY TO PRODUCTS
PURCHASED IN THOSE JURISDICTIONS (E.G., MEMBER STATES OF THE EUROPEAN ECONOMIC
AREA) IN WHICH PRODUCT WARRANTIES ARE THE RESPONSIBILITY OF THE LOCAL DEALER
FROM WHOM THE PRODUCTS ARE ACQUIRED. IN SUCH A CASE, PLEASE CONTACT YOUR
TRIMBLE DEALER FOR APPLICABLE WARRANTY INFORMATION.
Notice to Australian Purchasers – The Australian Consumer Law
Our goods come with guarantees that cannot be excluded under the Australian
Consumer Law. You are entitled to a replacement or refund for a major failure
and for compensation for any other reasonably foreseeable loss or damage. You
are also entitled to have the goods repaired or replaced if the goods fail to
be of acceptable quality and the failure does not amount to a major failure.
Trimble’s warranty, as set out in the user manual accompanying this statement,
or as described in the warranty card accompanying the Product you purchased,
is in addition to any mandatory rights and remedies that you may have under
the Australian Consumer Law.
Official Language
THE OFFICIAL LANGUAGE OF THESE TERMS AND CONDITIONS IS ENGLISH. IN THE EVENT
OF A CONFLICT BETWEEN ENGLISH AND OTHER LANGUAGE VERSIONS, THE ENGLISH
LANGUAGE SHALL CONTROL
Product specifications
- Power hot-swappable, 5V, Max Current. 1.5A
- I/O User replaceable module
- Standard: Charger/DC power-in, POGO port
- Wi-Fi 802.11 ah, 902~928MHz
- Environmental MIL-STD-810G. Independently tested and certified for:
- Operating temperature: -20 °C to +60 °C (-4 °F to +140 °F)
- Humidity: 90 % RH temp cycle –20 °C/60 °C (–4 °F/140 °F)
- Drop MIL-STD-810G, Method 516.7, Procedure IV
- Water MIL-STD-810G, Method 506.6, Procedure I
References
- Trimble Advanced Industry Solutions & Integrated Technology
- Recycling Waste Electrical and Electronic Equipment (WEEE) Certification
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>