Trimble PA1 Gateway Alpha Installation Guide
- June 5, 2024
- Trimble
Table of Contents
Trimble Gateway Alpha Install Guide
Install Overview
- The Trimble Gateway device includes internal Cellular, WiFi, and GPS antennas.
- Mount the module in or on the dash with a clear view of the sky unobstructed by metals, with the top pointing to the sky.
- Attach the module securely using the screws provided, strong two-sided tape, or plastic ties.
- Be sure the module is clear of driver activities and potential environmental hazards. - Connect to the vehicle Power and Engine Data using the cables and adapters noted in the following pages.
- The main cable includes an RP1226 connector for most late-model vehicles.
- Adapters are available to connect at the diagnostic port if needed, as well as a 2-pin cable for in-dash installations. - The optional white Ignition lead is available if needed, but most vehicles will boot normally using the J1939 Engine Data signal.
- The display will power from the three-pin Power/Ignition/Ground connector, while all Display communications take place over WiFi.
Vehicle-Specific Install Guides
- The page below includes install guides and videos covering most Makes and Models.
- No Trimble Gateway-specific guides exist at this time, but the guides can be used as references, as the vehicle connection points are the same.
- See the PCG tab for diagnostic port and RP1226 installs.
- See the PMG tab for 2-pin installs. - https://transportation.trimble.com/installations/
Additional Install Notes
- Trimble Gateway supports power inputs from 12 or 24 volt vehicles (6-36 volt functional range).
- Trimble Gateway includes internal antennas, but an external antenna is also available if needed.
- Part H-055-0519
- The module will automatically detect an external antenna and switch to it. - Trimble Gateway will automatically adjust to the baud rate of the vehicle J1939, whether 250k or 500k.
Standard Kit M-010-0728
- Trimble Gateway Module E-006-0638
- L-016-0728 Trimble Gateway RP1226 Main Cable
- Trimble Gateway 44-Pin Head.
- RP1226 for Power/Engine Data Connection to newer trucks or adapters for older vehicles.
- Power/Ignition/Ground Connector for Displays.
- Two RS232 Connections.
- Two discrete inputs. - H-048-0526 #8 x ¾” Mounting Screws
Adapters and Accessories
- M-010-0741 9-Pin Kit
- L-016-0737 - RP1226 to 9-Pin Adapter
- Connection to any approved 9-Pin Diagnostic Port - M-010-0743 Volvo/Mack Kit
- L-016-0737 - RP1226 to Volvo/Mack OBD-style Adapter
- Connection to Volvo/Mack diagnostic port on pre-2018 Volvo/Mack trucks with Volvo/Mack engine - L-016-0727 Trimble Gateway/PMG Adapter
- Connects a Trimble Gateway device to an existing PMG Main Cable, replacing the PMG - L-016-0734 Trimble Gateway/PMG Dual Adapter
- A “Y” connector to plug both a Trimble Gateway and a PMG into an existing PMG Main Cable
Trimble Gateway Box
LED Indicators
- LED1
- Solid Red = ON and Charging
- Off = Powered Off - LED2
- Solid Green = Cell Connected
- Off = No Cell Connection - LED3
- Rapid Blue Flash = Engine Data Connected
- Off = No Engine Data - LED4
- Solid Amber = GPS Fixed
- Blinking Amber = No GPS Fix
Main Cable Pin-out
Pin|
---|---
A and B| Input Power
C and D| Ground
31| Ignition Sense
6| J1708 High
7| J1708 Low
36| J1939 High
35| J1939 Low
TRANSFORMING THE WAY THE WORLD WORKS
Federal Communication Commission Interference Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Caution:
- Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.
- This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
This device meets all the other requirements specified in Part 15E, Section 15.407 of the FCC Rules.
Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance 20cm between the radiator & your body.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>