PETKIT 15714 Fresh Element Mini Smart Pet Feeder Instruction Manual

PETKIT 15714 Fresh Element Mini Smart Pet Feeder

Product Information

Specifications

• Product Name: FRESH ELEMENT Mini
• Power Source: 5 AA batteries (not included)
• Material: Stainless steel, plastic
• Connectivity: Wifi for app integration
• Compatibility: PETKIT app (App Store or Play Store)

Product Usage Instructions

Quick Setup (Device Setup)

1. Installing the Batteries:
   • Remove the battery cover on the bottom of the device.
   • Install 5 AA batteries with the correct orientation.
   • Slide the cover back and tighten the screws.
   • Replace batteries when low on power. Use alkaline batteries only.
2. Connect Power Adapter:
   • Plug the power adapter into the port on the bottom of the device.
3. Setting up the Main Device:
   • Place the device on a flat surface.
   • Position the food bowl on the bottom section for the magnetic snap.

Quick Setup (Opening Lid and Adding Food)

1. Open the Lid:

   • Hold down the button and lift the lid.

2. Insert Desiccant Packet:

   • Distribute moisture-absorbent material evenly in the
     compartment.

   • Close the compartment cover.

3. Add Cat Food:

   • Add dry cat food without exceeding the MAX line.
   • Ensure cat food sizes are between 5mm and 12mm.

Connect Using the APP
Download the PETKIT app, add a device, and follow the prompts to connect.

QUICK SETUP

DEVICE SETUP

1. *Installing the batteries (batteries sold separately) (Before installing batteries, make sure there is no food in the food storage container.)**
2. Remove the screws and slide off the battery cover on the bottom of the device.
3. Install 5 AA batteries in the battery compartment. (make sure they are installed with the correct orientation)
4. Slide the cover back into place and tighten down the screws.

• We strongly recommend replacing the batteries before leaving on a trip for an extended period. Make sure to replace batteries when they are low on power. (Use alkaline batteries only) 2. Connect power adapter
  Take the power adapter out of the food storage container, and plug it into the power adapter port on the bottom of the main device.

  3. Setting up the main device
  4. Please set the device on a flat, even surface.
  5. Place the food bowl on the bottom section of the device. The magnetic sensors will allow it to snap into place once it is in the correct position. (Please see the illustration below)

OPENING THE LID AND ADDING FOOD

1. Open the lid
   Hold down the “Open Lid” button and lift the lid. (You can scan the QR code below for further instructions on how to open the lid)

2. Insert a desiccant packet
   Lay the cover flat and open the compartment for the moisture-absorbent material. Stir the bag of moisture-absorbent material until it is spread evenly in the compartment, then close the compartment cover.

3. Add cat food

4. Add dry cat food. (Please do not exceed the MAX line)

5. Close the lid. *Sizes for cat food should be between 5mm and 12mm.

6. Connect using the APP
   Download the “PETKIT” app from the App Store or Play Store Enter the Home Page of the App- Click”+” on the right of “Device Lists” and add a device correspondingly. Follow the prompts to connect your device.

LIST OF PARTS

*Before setting up your device, please make sure you have all the necessary parts. (This product does not come with batteries or a screwdriver. You will need to purchase these separately.)

PRODUCT SUMMARY

*Note: To provide the best product, we will be implementing periodic product enhancements. If the illustrations do not match what you see on the device, please refer to the device as standard.

PRODUCT USAGE

1. Manual feeding
   Hold down the manual feeding button. The food outlet door will open and dispense food. Let go of the button, and the food outlet door will close and cease dispensing food.

2. Feeding remotely using the APP
   You can dispense food in real-time or set times for food to be dispensed via the remote control of the Petkit App.

INDICATION LIGHT INSTRUCTIONS

the internet or is unable to connect to the router.
Wifi indication light is blinking quickly| ① The device is searching for a wi-fi signal.

② The device is undergoing an update (Please refer to the notifications in your App)

Wifi indication light is on (constant)| The device is connected to the internet.
Wifi indication light is off| The device is not connected to the internet, or the indication light has been switched off.
The food level indication light is on (constant)| The food level is low.
The food level indication light is blinking| The device is not functioning properly.
Food level indication light is off| The food level is adequate.

CLEANING GUIDE

1. Open the top lid, and remove the food storage container. Pull out the food bowl set and separate the stainless steel food bowl from the food bowl support.
2. One by one, clean the food storage container (including the propeller blades), the stainless steel food bowl, and the bowl support. We recommend using an appropriate cleaning agent and rinsing clean.
   *Be aware that the exterior of the main device should not get wet.
3. Once washing is complete and the parts have air dried, install them back into the main device one at a time.
   *When putting the food storage container back in, lightly screw the food mixer back into the food storage container until the container is fully secured in the main device.

TROUBLESHOOTING

Friendly reminder: If there is a problem with the indication light (it doesn’t turn on), or if you are unable to dispense food manually, please first check the App settings, or try unplugging and plugging back the device again.

• The wi-fi indication light is not blinking properly.
  1. The device has lost its connection to the internet. Please check the internet in your area.
  2. If the internet is functioning properly, please open the “Device” page in the App, click the “setting” in the upper right corner, and reconfigure your device’s wi-fi connection.
• The food level indication light is on constantly.
  The food level is low. Please add food now.

Note: For troubleshooting other problems, as well as everyday maintenance information, please refer to the prompts in the App.

FAQ

• The Feeder Mini has lost its internet connection:
  If the Feeder loses connection to your home’s router will cause the device to get offline. Possible causes for this problem include:

1. Electricity has gone out in your home. If it happens, your router will not work and your Feeder will switch to battery power. If there are no batteries installed, then your device will cease working until power is restored. Before the batteries die, the Feeder will operate normally. However, the App will be unable to connect to your device. Records of feeding during this time will be labeled as “unknown”. (Note: once the internet connection is restored, you will only be able to update a maximum of 10 feeding records, and during this time you will be unable to adjust the feeding schedule.)
2. The internet connection has been interrupted in your home (this could be due to reasons such as your internet provider cutting internet service to your home). During this time, the Feeder will continue to operate normally, however, the App will be unable to connect to your device. Records of feeding during this time will be labeled as “unknown”. **(Note:** once the internet connection is restored, you will only be able to update a maximum of 10 feeding records, and during this time you will be unable to adjust the feeding schedule.)

• The Feeder Mini is not dispensing food properly:
  To dispense food on a specific schedule, the feeder dispenses a set amount of food each serving. Each
  serving is approximately 5g. The actual weight of each serving may vary depending on the type of food, the size of each pebble, and the density of the food. When the food storage container is full, each serving is relatively consistent in weight. In most cases, you can adjust the amount dispensed in your settings. When the food level is low, the portion size may shrink. Please make sure there is always enough food in the food storage container.

• Q: What should I do if the food level indication light blinks?
  A: If the light blinks, it indicates an unknown problem. Please check the device, connections, and food outlet door for any issues.

MESSAGE TO OUR VALUED CUSTOMERS

• Thank you for choosing to purchase the PETKIT Smart Feeder Mini. PETKIT works hard to make a better life for you and your pets through the implementation of science and technology.
• Before using, please carefully read the User Manual for this device. Installing and using this device means you have read and accepted the safety guidelines listed below.
• PETKIT is not responsible, nor does it accept any legal responsibility, for any accidents or losses caused by improper use of this device.
• PETKIT reserves the right to interpret and modify this notice.

HOW TO USE SAFELY

• Not respecting or abiding by the following guidelines may result in device malfunction or other unexpected accidents.

  • Only install and use the device as instructed in the User Manual.
  • This device is not recommended for pets younger than 3 months.
  • Please only use indoors.
  • This device operates under low voltage, however it may still lose power if pets chew on the power cable. Please make sure pets do not chew on the cord.
  • Only use the original power adapter. Otherwise, you may damage the device or cause a safety risk.
  • Please make sure the device is placed on a level surface. Do not overturn the device, or it may not function properly.
  • Only put dry pet food into the food storage container, or the device will not function properly, and it may even endanger the safety of the pet.
  • To prevent your pet from overturning this device, we recommend placing it in a corner or against a wall.
  • When dispensing food, please do not obstruct the dispenser opening.
  • The main body of the device should not get wet.
  • If you plan on leaving this device unused and unmoved for long periods, please remove any batteries and unplug the power cable.
  • Children should only be allowed to operate this device under the supervision of an adult.
  • To avoid unnecessary damage or injury, only repair technicians should be allowed to repair this device.
  • If you plan on being away from the device for an extended period, please make sure that the batteries installed in the device have sufficient charge (this device only uses alkaline batteries).
  • If you encounter any problems operating this device, please contact customer service.

BASIC SPECIFICATIONS

FCC

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and ；(2) this device must accept any interference received, including interference that may cause undesired operation.

FCC warning:
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, under part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used by the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

The device has been evaluated to meet general RF exposure requirements.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body.

IC warning
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) This device must accept any interference, including interference that may cause undesired operation of the device.

The device has been approved for use in EU countries and is therefore provided with the CE mark. All necessary documentation is available on the website: www.electric-collars.com Changes to technical parameters, properties, and printing errors are reserved.

Service center and distribution
Reedog, sro Sedmidomky 459/8 101 00 Prague 10
Phone: +1 646 980 4569
Email: info@electric-collars.eu

References

• ★☆ Electronic training collars for dogs ☆★ - Electric-Collars.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>