FUJITSU DL3100 Printer OmniData Services Group Instruction Manual
- June 13, 2024
- FUJITSU
Table of Contents
FUJITSU DL3100 Printer OmniData Services Group
Product Information
Specifications:
- Roll Paper Support Components:
- 2 x Paper Roll Shaft (Paper roll support, safety path)
- 2 x Support (secured with knob screws)
- 1 x Paper Roll
- 1 x Shaft
| Part | Description |
|---|---|
| Eje (Axis) | x 2 (paper roll support, safety route) |
| Soporte (Support) | x 2 (fixed with knob screws) |
| Rollo de papel (Paper Roll) | 1 |
| Base | x 1 |
| Placa de la pata (Foot Plate) | x 1 (fixed with knob screws) |
Product Usage Instructions:
1. Check Roll Paper Support Components:
Ensure you have the following components that form the roll paper support:
- 2 x Paper Roll Shaft (Paper roll support, safety path)
- 2 x Support (secured with knob screws)
- 1 x Paper Roll
- 1 x Shaft
2. Mount the Paper Roll and Shaft:
Securely mount the paper roll and shaft ensuring the correct path as follows:
- Place Ring E on the left and right sides of the shaft so they are outside the support.
- Fix the paper roll on the paper roll support.
- Secure the shaft to ensure the safety path.
3. Assembly:
Assemble the components in the following order:
- Base x 1
- Leg Plate x 1 (secured with knob screws)
4. Secure Components:
Secure the following components using knob screws:
- Support
- Base
5. Mounting:
Mount the assembly using the mounting holes as indicated.
Assembly Instructions
- Check the components that make up the rolled paper support:
- 2 x Axis (paper roll support, safety route)
- 2 x Support (fixed with knob screws)
- 1 x Paper Roll
- 1 x Base
- 1 x Foot Plate (fixed with knob screws)
- Mount the paper roll and the axis (ensuring the route) on the support:
- Place the E rings on the left and right sides of the axis so that they remain outside the support.
- Do not tighten the knob screws excessively.
- Slide the support to the right as indicated by the arrow, ensuring it is correctly positioned.
- Method of mounting on the printer:
- Place the base. After moving the tractor units to the left and right extremes, align the base with the runs on both the left and right sides of the printer and adjust from the top.
- Insert the foot plate into the base. Secure it with knob screws.
- Apply the supports to the base. Secure them with knob screws.
- Paper feed method for the paper roll:
- Turn on the printer and move the paper selection lever (right side of the printer) until it points to ” ” for roll paper feed.
- Insert the paper roll. When detected, it will be captured automatically.
- Move the paper selection lever backwards towards ” ” to set the continuous paper position. Then, pull the paper feed lever towards you to expel the roll paper. Align the paper edges on the left and right sides of the paper roll support.
- Once the paper roll is adjusted, move the paper selection lever forward until the pressure roller is closed.
- Place the sheet feeder along the slot.
FAQs
How do I ensure the paper roll is correctly positioned?
To ensure correct positioning, follow the steps to place Ring E on the shaft and secure it in the support.
What should I do if the paper roll does not feed properly?
Check the alignment of the paper roll and shaft, ensuring they are mounted securely and that the safety path is clear for smooth feeding.
How do you properly align the base with the printer?
Move the tractor units to the extremes and align the base using the runs on both sides of the printer, adjusting from the top.
What should you be careful with when tightening the knob screws?
Do not tighten the knob screws excessively to avoid damaging the components.
How do you ensure the paper roll is captured automatically?
Insert the paper roll into the printer and it will be detected and captured automatically.
What is the importance of the E rings in the assembly?
The E rings should be placed on the left and right sides of the axis to remain outside the support, ensuring safety and correct function.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>