ilovbee B87 Mechanical Keyboard Owner’s Manual

ilovbee B87 Mechanical Keyboard

PRODUCT BASIC

WIRED MODE

INDICATOR LIGHTS/KNOB FUNCTION

INDICATOR LIGHTS

KNOB FUNCTION

CONNECTIVITY

BT CONNECTIVITY

• BT Connection Method: As shown in the picture below, the keyboard switch is set to B state.

1. Place the switch to the side.

2. To pair the keyboard, press and hold any of the key combinations of FN+Q / W / E for 3 seconds.
   take Fn+Q for example, the Q key will quickly flash to indicate pairing mode, while a slow flash indicates reconnection mode.

3. Turn on the computer/phone/other devices, find and link to the keyboard whose name on the list shows ilovbee B87

4. Similarly, Repeat the previous steps to connect and pair each desired BT device using the FN +Q / W / E key combinations. Short press FN+Q / W / E to switch between the stored devices.

(kinder reminder: Please pair the 3 BT devices before switching between them.)

2.4G CONNECTIVITY
2.4G Connection: As shown in the figure below, the keypad switch is set to G status.

1. Place the switch to the side.
2. Long press FN+P to pair, insert the receiver when the P key rapidly flashes, and successful pairing is indicated when the P key stops flashing.
3. Slow flashing P key indicates the keyboard is in reconnection mode.

( Note: 2.4G receiver comes pre-paired. This method is only for troubleshooting 2.4G connection issues. Set it up once and no further setup is required.)

BATTERY REMINDER

Check the battery level in wireless mode FN+ Enter
For Example

• The backlight is bright, indicating that the keyboard is 10% of the power at this time
• The backlight is on at the same time, indicating that the keyboard is 20% of the power at this time

Similarly

• The backlight is on at the same time, indicating that the keyboard power is 100% at this time

DFU MODE

BACKLIGHT BRIGHTNESS/SPEED SETTING

CUSTOM BACKLIGHT SET

MULTIMEDIA KEY FOR WINDOWS

• Windows system(Fn + A: switch to Windows system)

MULTIMEDIA KEY FOR MAC

• MAC system(Fn + S: switch to Mac system)

FCC STATEMENT

This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:

1. This device may not cause harmful interference,
2. this device must accept any interference received, including interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a ClassB digital device, according to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used under the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Warning: Changes or modifications to this unit not expressly approved by the part responsible for compliance could void the user’s authority to operate the equipment.
FCC Radiation Exposure Statement
The device has been evaluated to meet general RF exposure requirements.
The device can be used in portable exposure conditions without restriction.

ISED STATEMENT
This device contains licence-exempt transmitters)/receivers) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:

1. This device may not cause interference.
2. This device must accept any interference, including interference that may cause undesired operation of the device. The digital apparatus complies with Canadian CAN ICES-3 (B)/NMB-3(B).

This device meets the exemption from the routine evaluation limits in section 2.5 of RSS 102 and compliance with RSS 102 RF exposure, users can obtain Canadian information on RF exposure and compliance.

This equipment complies with Canada’s radiation exposure limits set forth for an uncontrolled environment.

The keyboard can support VIA drivers: https://usevia.app/
Executive standard: GB/T 14081-2010 Made in China

References

• VIA

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>