RCA RNSMU7040 4K Ultra HD Smart TV Instruction Manual
- June 5, 2024
- RCA
Table of Contents
RCA RNSMU7040 4K Ultra HD Smart TV Instruction
SAFETY PRECAUTION
WARNING
TO REDUCE THE RISK OF ELECTRIC SHOCK
DO NOT REMOVE COVER C OR BACK .NO USER SERVICEABLE PARTS INSIDE. REFER
SERVICING TO QUALIFIED SERVICE
PERSONNEL. The lightning flash with arrowhead symbol A within an equilateral
triangle, is intended to alert the user to the presence of uninsulated
dangerous voltage” within the product’s enclosure that may be of sufficient
magnitude to constitute a risk of electric shock to persons. The exclamation
point within an equilateral Triangle is intended to alert the user to the
presence of important operating and maintenance (servicing) instructions in
the literature accompanying the appliance.
CAUTION
DANGER OF EXPLOSION IF BATTERY IS INCORRECTLY REPLACED. REPLACE ONL WITH THE
SAME OR EQUIVALENT TYPE.
- USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.
- TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
- TO REVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.
- DO NOT PLACE OBJECTS FILLED WITH LIQUIDS ON OR NEAR THIS UNIT.
- SHOULD ANY TROUBLE OCCUR, DISCONNECT THE AC POWER CORD AND REFER SERVICINGTO A QUALIFIED TECHNICIAN.
- This equipment is a Class II or double insulated electrical appliance.
- It has been designed in which a way that it does not require a safety connection to electrical earth.
- Do not use this unit in places that are extremely hot, cold, dusty or humid.
- Do not restrict the airflow of this unit by placing it somewhere with poor airflow, by covering it with a cloth, by placing it on bedding or carpeting.
SAFETY INFORMATION
When connecting or disconnecting the AC power cord, grip the plug and not
the cord itself. Pulling the cord may damage it and create a hazard. When you
are not going to use the unit for a long period of time, disconnect the AC
power cord.
RATING PLATE LOCATION
The rating plate is located on the rear of the unit.
FCC STATEMENTS
This unit has been tested and found to comply with the limits for a Class B
digital device, pursuant of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This unit generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communication. However, there is no guarantee
that interference will not occur in a particular installation. If this unit
does cause harmful interference to radio or television reception, which can be
determined by turning the unit off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the unit and receiver.
- Connect the unit into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user authority to operate the unit.
IMPORTANT SAFETY INSTRUCTIONS
- Do not use this apparatus near water.
- Clean only with a dry cloth.
- Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
- Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (Including amplifiers) that produce heat.
- Do not defeat the safety purpose of the polarized or grounding-type plug.
- A polarized plug has two blades with one wider than the other.
- A grounding type plug has two blades and a third grounding pronghe wide blade or the third prong is provided for your safety.
- If the provided plug does not fit into your wall outlet, consult an electrician for replacement of the obsolete outlet.
- Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.
- Only use attachments/ accessories specified by the manufacturer.
- Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus.
- When a cart is used, use caution when moving the cart/ apparatus combination to avoid injury from tip-over.
- Unplug this apparatus during lightning Storms or when unused for long periods of time.
- Refer all servicing to qualified service personnel. Servicing is required when the apparatushas been damaged in any way, such as the power cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
- The mains plug is used as disconnect device, the disconnect device shall remain readily operable.
PERSONAL SAFETY NOTICE
ALWAYS read and follow all instructions for the installation and use of the
TV.
- Place the TV in a location that is level and sturdy.
- DO NOT place the TV on a furniture with drawers that can be used as steps by small children.
- DO NOT allow children to pull the TV or climb on the furniture where the TV is placed.
- DO NOT allow children to play in front of or around the TV
- ALWAYS route all the cables connecting to the TV so the cables cannot be easily pulled an grabbed by children.
- When installing the TV on a wall, please purchase a TV mount recommended by a professional TV installer, and follow the installation instructions that come with the TV mount
- Before installing the TV on a wall, please check to make sure the wall structure can suppor the weight of the TV and the mount. If in doubt, please ask the advice from a professional TV installer
FCC Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance 20cm between the radiator & your body.
ACCESSORIES
- Remote control x 1
- Battery (AAA) x 2
- Instruction Manual x 1
- Base stand x 2
- Base stand screws x 4
- Troubleshooting instructions card x 1
GETTING STARTED
USING THE REMOTE CONTROL
- Point the remote control at the remote sensor located on the unit.
- When there is a strong ambient light source, the performance of the infrared remote sensor may be degraded, causing unreliable operation.
- The recommended effective distance for remote operation is about 16 feet (5 meters).
TO INSTALL THE BATTERIES
Open the battery door
Insert 2″AAA”batteries.
BATTERY REPLACEMENT
When the batteries become weak, the operating distance of the remote control is greatly reduced and you will need to replace the batteries.
CAUTION
Danger of explosion if battery is incorrectly replaced.
NOTES
If the remote control is not going to be used for a long time, remove the
batteries to avoid damage caused by battery leakage corrosion. Do not mix old
and new batteries. Do not mix ALKALINE, standard (CARBON-ZINC) or rechargeable
(NICKEL-CADMIUM) batteries. Always remove batteries as soon as they become
weak. Weak batteries can leak and severely damage the remote control.
CONTROL REFERENCE GUIDE
REMOTE CONTROL
Remote control system code: TC9012 Customer code: OE
- POWER : Turns the TV on or off.
- MUTE: Mute or restore the sound.
- Number buttons: Choose the channel directly.
- LIST: Access the channel list.
- SOURCE: Select the input source mode.
- HOME( 0 ): Enter the home page.
- Return(Back): Return to the previously-viewed channel. MENU: Access the main menu.
- EXIT: Exit the current screen.
- Navigation buttons: Up/Down/Left/Right◄/► Navigate the menu.
- OK: Confirm the selection.
- NETFLIX: Access the Netflix interface.
- PRIME VIDEO: Access the Prime Video interface.
- Access the Internet.
- YOUTUBE: Access the YouTube interface.
- VOL +NOL Increases or decreases the TV volume.
- CHA/CHV: Change to the previous or next program.
- CC: Setup the mode of closed caption.
- GUIDE: Shows Electronic Program Guide.
- FAST BACKWARD/FAST FORWARD +1 : Fast review of fast forward.
- PLAY ► : Play while watching media.
- PAUSE 11 : Pause while watching media.
- SUBTITLE: Access the subtitle.
- AD: Shortcut voice channel of blind.
- Color Buttons(RED/GREEN/YELLOW/BLUE): Execute the prompt function in specific mode.
IMPORTANT NOTICE
Depending on the country where the TV is installed, certain apps may not be
available. The quick launch button on the remote control associated with those
apps will therefore not work. All other functionalities of the remote will
work as designed.
FRONT VIEW
About remote control working distance and angle . Power/Standby Indicator: Blue and red dual-color LED. It shows red when the TV is turned off and blue when turned on. Remote Control Sensor: Remote control lR sensor, which receives infrared ray sent by remote control. If there is a protective film around the screen, remove the protective film before using the TV.
SIDE VIEW
- CH Scans up through the channel list. In the input source menu, it acts like the up arrow on the remote control.
- CH. Scans down through the channel list. In the input source menu, it acts like the down arrow on the remote control.
- VOL+: Increases the volume.
- VOL-:Decreases the volume.
- INPUT: When lV power off, short press this button to turn on. When lV is on, long press this button to turn off, short press this button to call out the input source menu, press the CH+/- button to select the input source and press the power on/off button again to confirm the selection.
BACK VIEW
CVBS
Connect an AV device that has composite video jacks, such as a VCR or DVD
player.L: Left audio channel connection. R: Right audio channel connection.
LAN
Connect the Internet.
HDMI
(High Definition Multimedia Interface) Provides an uncompressed digital
connection. Please enter
to the setup menu to turn it on.
OPTICAL
Digital TV sound output.
Service
This port is used by professional maintenance personnel when repairing the
machine.
RF
Connect to receive the signal from your antenna or cable through a coaxial
cable.
USB
Connect the USB device such as the flash disk to access the TV media function.
HDMI Link (HDMI 1 )
Command and control HDMI devices connected to the TV set. Please enter to the
setup menu to turn it on.
WALL MOUNT INSTALLATION
INSTALLING/ REMOVING THE BASE STAND
WARNING
The LED Display is very fragile, and must be protected at all times when
removing the base Stand .
Be sure that no hard or sharp object or anything that could scratch or damage the LED display comes into contact with it Do NOT exert pressure on the front of the unit at any time because the screen could crack.
- Disconnect all cables or cords connected to the unit.
- Lay the unit down on a flat surface with the back side facing up Please make sure to place a soft cushioned material such as a pillow or thick piece of foam) beneath the screen.
- To remove the base stand, loosen screws off the holes then pull downwards to release the base stand.
MOUNTING ON THE WALL
This unit is VESA-compliant, and is designed to be wall-mounted with a VESA- compliant16″x12″ (400mm x 300mm) mounting kit designed for flat panel TVs. Length of screw should be not exceed 8 mm
NOTE
Remove the base stand before mounting the unit on the wall.
Installation
Your TV is packaged with the stand and the cabinet separated. Before using the TV, install the stand as described below, or if you want to mount it to a wall, the wall mount itself is not supplied.
IMPORTANT
Make sure the TV set is unplugged from the power supply before installing or removing the stand. The TV panel may be awkward to install on your own. We recommend you ask someone to help with installation and/or removal of the stand.
Attaching the stand
Step 1
Place a soft cushioned material on top of a flat surface to prevent damaging
the screen panel. Then place the TV monitor flat on top, with the screen side
facing down, as illustrated on the right.
Step2
Align the screw holes on the stand and the bottom of the TV, as illustrated on
the right.
Step 3
Tighten the screws supplied with a screwdriver to affix the stand to the
panel, as illustrated on the right (3). Do not apply excessive force as this
may damage the screw holes.
CONNECTIONS
CONNECTING A TV ANTENNA/ CABLE/ SATELLITE
To view tel.evision channels correctly, a signal must be received from one of the following sources.
- An indoor or outdoor aerial antenna.
- A cable system.
- A satellite system.
NOTE
For receiving over-the-air TV broadcasts, we recommend that you use an
external fixed antenna. Should you require the use of a temporary antenna,
please ensure that you purchase an antenna with sufficient ability to receive
in weak signal areas. Only when you are in close proximity to a transmitter
will a temporary antenna reproduce a signal as strongly as a fixed antenna.
CONNECTING AN A/V DEVICE
To connect to other equipment such as a VCR, camcorder, satellite system or cable, etc.
CONNECTING DEVICESWITHA COMPOSITE VIDEO OUTPUT
To connect A/V devices such as a VCR, video game system or camcorder. Conne cting to a VCR/ Video Game Syst em/ Camcorder. Connect the AUDIO /VIDEO cable. Make sure you connect the cable from the other equipment ( AUDIO and VIDEO OUT) to this unit AV in.
NOTE
Composite video input shared with component
CONNECTING A HIGH-DEFINITION (HD) SOURCE USING HDMI CONNECTION
HDMI (High Definition Multimedia Interface) supports both video and audio on a single digital connection for use with DVD players, DTV, set-top boxes and other digital AV devices. HDMI was developed to provide the technologies of High Bandwidth Digital Content Protection (HDCP) as well as Digital Visual Interface (DVI) in one specification. HDCP is used to protect digital content transmitted and received by DVI-compliant or HDMI compliant displays. HDMI has the capability to support standard, enhanced or high-definition video plus standard to multi-channel surround-sound audio. HDMI features include uncompressed digital video, a bandwidth of up to 2.2 gigabytes per second (with HDTV signals), one connector (instead of several cables and connectors), and communication between the AV source and AV devices such as DTVs.
CONNECTING THE POWER CORD
You can power on your TV unit before you make sure the power cord is inserted well. At the same time, please check that the rated voltage of your unit matches your local Voltage.
NOTE
- Insert the power plug fully into the socket outlet. (If the power plug is loose, it could generate heat and cause fire .)
- Ensure that the power plug is easily accessible.
- Ensure the earth pin on the power plug is securely connected to prevent electrical shock.
- Do not touch the power plug with a wet hand this may cause electrical shock.
- Do not use any power cord other than that provided with this TV. (This may cause fire or electrical shock.)
- Do not damage the power cord. A damaged cord may cause fire or electrical shock.
- Do not move the TV with the cord plugged in the socket outlet.
- Do not place a heavy object on the cord or place the cord near a high-temperature object.
- Do not twist the cord, bend it excessively, or stretch it.
- Do not use a damaged power plug or socket outlet.
Connection to a Home Theater Audio System
For BEST audio performance
Connecting to a Home Theater System Dolby Digital can deliver optimal 2
channel stereo or surround sound with five discrete full range channels plus a
sixth channel for a subwoofer.
Enjoy optimal sound reproduction from your system with a Dolby Digital
amplifier that incorporates a digital optical input. Connect an optional
digital cable directly to the television’s optical audio output to listen
through all inputs except VGA.
How To Setup SPDIF Mode
- Press the MENU button on the remote control Press the arrow button to select SPDIF Mode in sound menu.
- Press OK button enter the Sub-menu.
- Press down T arrow button to select PCM, Auto, Transcode DD or Transcode DDP.
- Please set the SPDIF Mode to PCM when using the digital amplifier normally.
INITIAL SETUP
PUTTING THE UNIT ON A PROPER PLACE
When you tum on your television set for the first time, be sure to place it on
a solid stable surface. To avoid danger, do not expose the TV to water, or a
heat source (e.g. lamp, candle, radiator).
Do not obstruct the ventilation grid at the rear and be sure to leave
sufficient gaps around the unit.
TURNING THE UNIT ON FOR THE FIRST TIME
After you have initially connected your TV antenna or cable, turn the television ON. A screen will display asking you to select a Language, Environment, Country, Time Setting, Network Connection, Antenna Type and Auto Tuning.
SOURCE SELECTION
- Press the SOURCE button on the remote control.
- Use the T button to select the options (TV, AV, HDMl1,HDMl2,HDMl3) and select any of them using the OK button. The screen will change to your desired source.
- Before watching please make sure all necessary cables and devices are connected.
TV SETUP
Picture Menu
Press MENU button to display the main menu. Press IT button to select PICTURE in the main menu,it will highlight the option.
Picture Mode
Choose among Standard, Movie, User and Dynamic/Soccer depending on the region.
It will be set to “User” mode automatically when you adjust any of the
following six items.
This product is on standard picture mode in default, this is a power saving
mode and the picture will be a little dark. Please change the picture mode to
the desired mode from this setup menu.
Contrast
Adjust the difference between light and dark areas of the picture.
Brightness
Adjust the lightness of the picture.
Color
Adjust the richness of the picture.
Sharpness
Adjust the edge of the picture.
Tint
Only for some sources) Adjust the tint value of the color.
Backlight
Adjust the backlight value of the TV screen. Color Temperature: Select the
overall color tone of the picture. Choices are Cool, Nature, Warm and User.
Aspect Ratio: Select the aspect ratio display proportions) according to your
video signal type or preference. Choices are Auto, 4:3, 16:9, Movie or
Panorama. Noise Reduction: Eliminate noise in the picture. Choices are Off,
Low, Middle and High.
MPEG Noise Reduction
Eliminate noise generated while creating digital picture signals.
Dynamic Contrast
Turn on or turn off the function of dynamic contrast.
Film Mode
Turn on or turn off the function of film mode.
Sound Menu
- Press MENU button to display the main menu.
- Press Ii.IT button to select SOUND in the main menu,it will highlight the option.
- Sound Mode: Choose among Standard, Music, Movie, Soccer and User depending on the region, User.
- It will be set to User mode automatically when you adjust the value of 12GHz, 50GHz, 1.SKHz, SKHz or 1 0KHz.
- Balance: Control the sound balance between the right and left speaker.
- Auto Volume: Turn on to adjust the sound volume depending on the input signal.
- Surround Sound: Help to create rich and wider sound from stereo sound sources.
- SPDIF Mode: Set the SPDIF sound output mode.
- Advanced Effect DAP: Setup the advanced effect of Dolby Audio Processor Only for some regions.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>