genexis G6426 Fiber Twist Installation Guide
- June 11, 2024
- genexis
Table of Contents
G6426 Fiber Twist
Installation Guide Fiber Twist
P6426/G6426
Installation Guide
G6426 Fiber Twist
Installation with use of app
You’re just a few steps away to install your device via the Genesis Easy WiFi
app
Scan QR-code
https://genexis.eu/content/uploads/app-redirect/index.html
Download app and follow the steps
Installation guide
Box contents
- Genexis Fiber Twist (active device)
- Power adapter
- Labels (self-adhesive)
Label position
The product label is positioned on the bottom of the active device. The
relevant device information is also listed on the additional labels included
in the giftbox.
Preparation
Ensure there is a power socket within reach of where the device is being
installed.
Genesis EaSy WIFi app
Installation and management of the Genesis Fiber Twist device can be done with
help of the mobile application Genesis Easy WiFi. Please follow the steps on
the left page.
Important: Instructions need to be followed precisely and uninterrupted.
This minimizes the risk of damage to the fiber optic connectors, causing a
severe degradation of signal quality.
Warning: Do not cover the device, this will interfere with the
ventilation. Ambient Operating Temperature: 0°C ~ 40°C
Remove Blind Cover or active device (if present)
- Press and hold the unlock button (on the right side of the Blind Cover or active device).
- Rotate the Blind Cover or active device counterclockwise till it blocks.
- Remove the Blind Cover or active device from the baseplate (FTU) by pulling it towards yourself.
- Store the Blind Cover or active device in a safe place.
Remove dust cap
- Take the Fiber Twist out of the box.
- The dust cap is connected to the red string located on the rear of the Fiber Twist.
- Remove the dust cap by pulling the red string.
- Store the dust cap in a safe place.
Twist!
- Place the Fiber Twist on the FTU/Bracket as shown in the picture below.
- Rotate clockwise until it clicks into place.
- Make sure the Fiber Twist is aligned squarely on the FTU/Bracket. Your Fiber Twist is now installed!
Setting up the Fiber Twist
- If required, connect your telephone to a telephone port via an RJ11 phone cable.
- If required, connect your personal devices to the LAN ports via an RJ45 network cable.
- If required, connect your television / set-top box to the TV port with a coax cable.
- Connect the supplied power adapter to the Fiber Twist and plug the adapter into a power socket.
- Toggle the ON/OFF button on the bottom of the Fiber Twist in the ON position to turn on the device.
- If the device is connected properly and the service is active on the fiber port, the Status, Uplink and Internet LEDs will have a solid green color.
Switching the WiFi ON/OFF
The WiFi function of the Fiber Twist can be switched ON or OFF by means of the
Mode button.
- Switch OFF: On the Fiber Twist, press and hold the Mode button until the WiFi LED turns off.
- Switch ON: On the Fiber Twist, press and hold the Mode button until the WiFi LED turns on.
Connecting to the wireless network
You can connect your personal device to the FiberTwist via manual pairing. If
Automated pairing (WPS) is prefered, please check for your specific device how
this can be initiated.
Before pairing , make sure the WiFi LED is on (solid green). If not, switch
the WiFi ON as described in this installation guide. Manual pairing
The WiFi network name and WiFi key are printed on the labels of the
FiberTwist.
- Perform a search of available wireless networks on your personal device or scan the QR-code on the label of the FiberTwist.
- Select the WiFi network name printed on the labels of the FiberTwist.
- Enter the WiFi key printed on the labels of the FiberTwist.
Using the web interface
You can access the FiberTwist web interface via a wired connection or wireless
connection.
- Wired connection: Connect an RJ45 network cable between your personal device and the FiberTwist LAN port (yellow connector).
- Wireless connection: Connect your personal device to the wireless network as described in this installation guide.
- Use a web browser on your personal device and navigate to the GUI URL as printed on the labels of the FiberTwist.
- Login using the credentials as printed on the labels of the FiberTwist.
Power saving options
Power saving options are available via the web interface.
Warning: This product contains a laser that emits invisible light. It is
a Class 1 Consumer Laser product according to EN 50689:2021, which means it is
safe under all conditions of normal use. However, it is still advised to not
look directly into the fiber connector when the product is powered on.
LED overview
Button overview
Port overview
Reset button (recessed)
Reboot – short press once
Factory reset – long press and hold until all LED’s start fast blinking green
ON/OFF switch
Switch ON – flip the switch to ON
Switch OFF – flip the switch to OFF
Troubleshooting
Is the Status LED solid red?
Contact your service provider.
Is the Status LED not solid blue after automated pairing (WPS)?
Automated pairing between the FiberTwist and personal device failed. Please
follow the instructions again to connect your personal devices to the
FiberTwist via the wireless network.
Is the Status LED blinking yellow and the Uplink LED is blinking green?
The FiberTwist is being upgraded with new software. Please wait until the
Status LED turns solid green again.
Is the Uplink LED off?
If the Uplink indicator LED is off, despite proper connection, contact your
service provider.
Is the Uplink LED blinking red?
Contact your service provider.
Is the Internet LED blinking green for 5 minutes?
FiberTwist does not have a connection with the broadband network. Please
contact your service provider.
Is the WiFi LED off?
On the FiberTwist, press and hold the Mode button until the WiFi LED starts
blinking green or turns solid green.
Return the FiberTwist to factory default settings
With the reset button you can reset the FiberTwist to its factory default
settings.
You can press this button with a small pin or paperclip.
- Press and hold the reset button until all LED’s start fast blinking green.
- Wait until the Status LED turns solid green again.
EU Declaration of Conformity
Hereby, Genexis Netherlands B.V. declares that the radio equipment type
FiberTwist is in compliance with Directive 2014/53/EU, Directive 2009/125/EC,
Directive 2011/65/EU and Delegated Directive 2015/863.
The full text of the EU declaration of conformity is available at the
following internet addresses:
https://genexis.eu/product/fibertwist/red/fibertwist-p6426,
https://genexis.eu/product/fibertwist/red/fibertwist-g6426
Company Name
Genexis Netherlands B.V.
Company Address
Lodewijkstraat 1a
5652 AC Eindhoven
The Netherlands
Name and title of authorized person
Maarten Egmond, CTO
Signature of authorized person
Frequency bands and maximum radio frequency power transmitted
The FiberTwist P6426/G6426 operates in the frequency bands of 2.4 GHz and
5GHz.
The maximum radio frequency power transmitted in these bands is:
- 20 dBm (100 mW) (EIRP) for the 2400 MHz – 2483.5 MHz band
- 23 dBm (200 mW) (EIRP) for the 5150 MHz – 5350 MHz band *
- 30 dBm (1000 mW) (EIRP) for the 5470 MHz – 5725 MHz band
- In EU, 5150 – 5350 MHz is restricted to indoor.
People deserve fiber
Revision 2.0 – November 2023 – Copyright
© 2023 Genexis Netherlands B.V.
All rights reserved.
Multiple languages of this document and additional product information
are available on https://genexis.eu/product/fibertwist/downloads
Genexis assumes no responsibility for any inaccuracies in this document.
Genexis reserves the right to change, modify, transfer, or
otherwise revise this publication without notice.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>