Jaycar GH1676 Brass Monkey Single Door Caravan Instruction Manual
- June 10, 2024
- Jaycar
Table of Contents
- Jaycar GH1676 Brass Monkey Single Door Caravan
- Product Information
- Product Usage Instructions
- Frequently Asked Questions
- WARNINGS & SAFETY INFORMATION
- BEFORE FIRST USE
- FEATURES
- BOX CONTENTS
- PRODUCT DIAGRAM
- OPERATION
- INSTALLATION
- ADJUSTING THE FREEZER ZONE
- DOOR HINGE DIRECTION
- TROUBLESHOOTING
- CLEANING, CARE, STORAGE & MAINTENANCE
- SPECIFICATIONS
- WARRANTY INFORMATION
- Documents / Resources
Jaycar GH1676 Brass Monkey Single Door Caravan
Product Information
Specifications:
- Model: GH1676
- Capacity: 65L
- Type: Caravan Fridge
Product Usage Instructions
Before First Use
Ensure all box contents are present and inspect the refrigerator for any damage. Report any transportation damage immediately to the place of purchase.
Operation
- The product features a three-level battery protection function.
- Select the appropriate level (L, M, H) based on the type of battery powering the fridge.
- Error code F1 indicates voltage protection mode.
Installation
-
Check the refrigerator for damage upon opening.
-
Installing in a cavity/cabinet:
- Ensure proper ventilation space around the refrigerator.
- Place refrigerator on a flat, level surface away from heat
sources.
-
Connect to a power supply:
- Use an appropriate wire gauge based on the distance between the refrigerator and the battery.
- Ensure excess wire for moving the fridge in and out of the cabinet.
Adjusting the Freezer Zone
- Pull out the freezer zone lid horizontally.
- Pull out the divider horizontally.
Door Hinge Direction
- Follow step-by-step instructions to reverse the door hinge direction if needed.
Frequently Asked Questions
Q: What should I do if error code F1 appears on the panel?
A: Error code F1 indicates voltage protection mode. To resolve this, charge the battery or adjust the battery protection mode to a lower setting (from H to M, or M to L).
WARNINGS & SAFETY INFORMATION
- WARNING: The manufacturer is not responsible for any potential injury from misuse
- Do not operate the appliance if it is visibly damaged.
- Do not block the gaps in the fridge with things like pins or wires, etc.
- Do not expose the appliance to rain or immerse it in water.
- Do not place the appliance near naked flames or other heat sources (heaters, direct sunlight, gas ovens etc.)
- Do not store any explosive substances like spray cans with a flammable propellant.
- Ensure the supply cord is dry and not trapped or damaged. Do not locate multiple portable socket outlets or portable power supplies at the rear of the appliance.
- Check the voltage specification on the type plate corresponds to that of the energy supply. The appliance is only to be used with the power supply unit provided with the appliance.
- Do not use electrical appliances inside the food storage compartments of the appliance, unless they are of the type recommended by the manufacturer.
- Once unpacked and before turning on, the appliance must be placed on a level surface for more than 6 hours.
- Make sure that the appliance stays horizontal when it is running. The tilt angle must be less than 5° for long-time running and less than 45° for short-time running.
- Keep the ventilation openings in the unit casing or the built-in structure free of obstacles.
- Keep the appliance stable on the ground or in the car; Do not drain upside down.
Caution
- Repairs may only be carried out by qualified personnel. Incorrect repair may cause danger. The lamp and supply cord must be replaced by the manufacturer or qualified persons.
- The installation of DC power in a boat must be handled by qualified electricians.
- Children shall not play with the appliance. Cleaning and user maintenance shall not be done by children without supervision.
- The appliance can be used by children aged 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they’ve been given supervision or instruction concerning the use of the device in a safe way and understand the hazards.
Notice
- Disconnect the power supply before each cleaning and maintenance and after every use.
- Do not use sharp tools to defrost; Do not damage the refrigerant circuit.
- Risk of child entrapment. Before you throw away your old refrigerator or freezer: take off the doors: and leave the shelves in place so that children may not easily climb inside.
- Check if the cooling capacity of the appliance is suitable for storing food or medicine. Food may only be stored in its original packaging or suitable containers.
- If the appliance is left empty for long periods, switch off, defrost, clean, dry, and leave the door open to prevent mould from developing within the appliance.
- The appliance is intended to be used in household and similar applications such as:
- Staff kitchen areas in shops, offices and other working environments;
- Camping, Farmhouses and by clients in hotels, motels and other residential environments;
- Bed and breakfast type environments;
- Catering and similar non-retail applications.
- Information, illustrations and specifications in this manual reflect the most current available at the time of publication and are subject to change without prior notice.
- Due to the flammable refrigerant and blowing gas contained in the device, comply with local regulations for disposal.
BEFORE FIRST USE
- Prior to using your product, please read all the safety and operating instructions thoroughly. Please ensure you follow the steps below before using the product.
- We recommend you keep the original packaging for storing the product when not in use.
- Please pay close attention to the section entitled Warnings & Safety Information. Find a safe and convenient place to keep this instruction manual for future reference.
- Unpack the product but retain all packaging materials until you are satisfied that your new product is undamaged and in working order. Ensure you have all accessories listed in this manual.
FEATURES
- High-efficiency DC compressor and module which is robust and durable.
- Fast cooling to 0° C (based on 25° C ambient temperature).
- Intelligent voltage detection system to protect car battery.
- CFC-free and low energy consumption.
- Designed to be powered by 12V/24V DC.
- LCD for temperature setting.
- Bluetooth APP for temperature monitor and control.
BOX CONTENTS
- 1 x 95L Portable Dual Zone Fridge/Freezer
- 1 x 240V Mains Power Adaptor
- 1 x 12/24V Cigarette Lighter/Merit Car Charger
PRODUCT DIAGRAM
OPERATION
How to Turn on the Fridge
- Connect to 12/24V power
- Press the power button
- The internal temperature will display
Temperature Setting
- Press , to display ‘FR’( freezer zone temperature setting) or ‘RE’ (refrigerator zone temperature setting).
- Select either the fridge zone or the freezer zone temperature. You cannot select separate temperatures for each zone at the same time; you must choose which zone you want to more accurately control the temperature of.
- The zone not selected to control the temperature will be then cooled as a slave zone relative to the temperature set by the other zone.
- Press “+ “ or “ – “ to adjust the temperature of the respective zone.
To Reset
- Power off the fridge
- Holding the setting button until E1 is displayed.
- Press buttons “+” and “—” at the same time until the display is as below.
Battery Protection Mode Setting
- The product has a three-level battery protection function, which not only guarantees the normal operation of the product but also protects the battery of the vehicle.
- When powered on, long press the settings button for 3 seconds and the display screen flashes H, select low voltage production L(ow), Medium), and High) by clicking the settings button . The factory default is set to L(ow) protection.
- From left to right: L/M/H.
- H should be selected when the fridge is connected to the vehicle starter battery, and M or L should be selected when powering from a deep cycle battery.
- If error code F1 is shown on the panel it means that the fridge is in voltage protection mode, meaning the fridge will operate again once the battery is charged or the battery protection model is lowered from H to M, or M to L.
INSTALLATION
- Ensure that the refrigerator is in good order and not damaged when opening the packaging for the first time.
- Any transportation damage must be reported promptly to the place of purchase within 24 hours of taking delivery.
- Handle the product with the utmost care and attention.
- When installing in a cavity/cabinet.
- The refrigerator dimensions are 470430630mm (ACB), and there should be enough space (75mm minimal) at the rear and top of the refrigerator to ensure adequate ventilation.
- There should be a minimum of 7.5mm of space on each side.
- Cabinet dimensions suggested 485505705mm (A1C1B1).
- Always place the refrigerator on a flat and level surface that is adequate to support its weight.
- Place the refrigerator in a location away from heat sources and ensure that it has enough ventilation.
- Connect to a power supply
- Connect the refrigerator to the vehicle 12/24VDC system directly, the minimal cable cross-section as per the below table based on the overall length of wire between the refrigerator and the battery.
- Enough excess wire needs to be kept to allow for moving the fridge into and out of the cabinet.
Wire Length to Refrigerator | Wire Gauge |
---|---|
Maximum 6 m | 14AWG |
Maximum 11m | 12AWG |
Maximum 17m | 10AWG |
- It is highly recommended that the installation fridge is carried out by a qualified person.
Push the refrigerator into the cabinet
- Push the refrigerator into the cabinet carefully to avoid scratching the floor, and that the power cable is kept loose, and is not kinked or damaged.
Mount the fridge with the cabinet wall
- Mounting points (holes) are built into the side wall of the refrigerator, a hole needs to be drilled into the cabinet to line up with the mounting points on the side of the fridge.
- Fix the fridge with screws (M5, 15mm minimum to the cabinet walls, then use the screw covers included to hide the screws. A total of 4 screws are required (not included) for installation into a cabinet.
Verify the installation
- Once the installation has been finished, check the continuity of the negative circuit and carry out all electrical safety testing provided for by current regulations.
- Protect and fix the cables to prevent accidental pulling of the cable and from disconnecting from any connections or the power source and ensure it doesn’t come into contact with heat sources with a temperature of 50°C or more, or with sharp objects.
ADJUSTING THE FREEZER ZONE
- Open the freezer zone lid and make a 75°angle between it and the right border of the fridge.
- Pull out the freezer zone lid horizontally.
- Pull out the divider horizontally.
DOOR HINGE DIRECTION
- Unscrew the bottom hinge (9)
- Take off the door body (keep the fridge stable)
- Unscrew and take off the door latch (8), install it into the new location of the door latch (6)
- Remove the door head decorative sheet (5), and install it into a new location of door head decorative sheet (7).
- Move the top door axle (1) and bottom door axle (3) to new position (2)(4)
- Install the door to the refrigerator, fasten the top door axle with the top hinge; install the bottom hinge screws (4), fix the door with the hinge;
- Close the door, the door opening direction is now reversed.
TROUBLESHOOTING
ISSUE | SUGGESTED REMEDY |
---|---|
The refrigerator does not work | • Check if the switch is on. |
• Check if the plug and socket are connected well.
• Check if the fuse has been burnt.
• Check if the power supply is malfunctioned.
• Switch on/off the fridge frequently may cause a start delay in the compressor
Refrigerator compartments are too warm| • The lid is opened frequently.
• A large amount of warm or hot food was stored recently.
• The refrigerator has been disconnected for a long time.
Food is frozen| The temperature was set too low
There is a “water flow” noise from inside the refrigerator| It’s a normal
phenomenon, caused by the flow of refrigerant.
There are waterdrops around the refrigerator casing or door gap| It’s a normal
phenomenon, the moisture will condense to water when it touches the cold
surface of the refrigerator.
The compressor is slightly noisy when starting| It’s a normal phenomenon, the
noise will be reduced after the compressor works stably.
Code F1 displayed| Possible cause: low voltage to the fridge.
Adjust the battery protection from High to Medium or from Medium to Low.
Code F2 displayed| Possible cause: The condenser fan is overloaded. Disconnect power to fridge for 5 minutes & re-start.
If the code shows again, contact the manufacturer for service.
Code F3 displayed| Possible cause: the compressor starts too frequently. Disconnect power to fridge for 5 minutes & re-start.
If the code shows again, contact the manufacturer for service.
Code F4 displayed| Possible cause: compressor not kicking in. Disconnect power to fridge for 5 minutes & re-start.
If the code shows again, contact the manufacturer for service
Code F5 displayed| Possible cause: overheating of the compressor & electronics. Disconnect power to fridge for 5 minutes & re-start.
If the code shows again, contact the manufacturer for service.
Code F6 displayed| Possible cause: no parameter can be detected by the controller. Disconnect power to fridge for 5 minutes & re-start.
If the code shows again, contact the manufacturer for service.
Code F7 or FS displayed| Possible cause: temperature sensor is faulty. Contact manufacturer for service.
CLEANING, CARE, STORAGE & MAINTENANCE
WARNING: Never use hard or sharp tools to remove ice or to loosen objects frozen in place.
Cleaning
- Unplug the device first to avoid electric shock.
- Use a wet cloth to clean the device and dry it.
- Remove the cover and drain from the hole at the bottom of the device.
- Do not soak the device in water and do not wash it directly.
- Do not use abrasive cleaning agents as these can damage the device.
Storage
- If the device will not be in use for a long time, please follow the steps:
- Turn off the power and remove the plug.
- Remove all the items stored in the device.
- Remove the cover and drain from the hole, wipe off excess water with a soft rag.
- Leave the lid slightly open to prevent odour formation.
- Put he device in a cool and dry place.
Defrosting
- Humidity can form frost in the interior of the cooling device or on the evaporator, which will affect the cooling performance.
- Defrost the device regularly to avoid this.
- Switch off the device.
- Take out the contents of the device.
- Keep the lid open.
- Remove the cover and drain from the hole.
- Wipe off the defrosted water.
SMART CONTROL – FRIDGE APP INSTRUCTIONS
- Downloading the “BRASS MONKEY” Application
- Using a pre-installed QR reader on your handheld smart device scan the QR code in the manual or on the carton, or search for the “BRASS MONKEY” APP in the iTunes”App Store (for Apple” devices) or Google store (Android Devices)
- Start the application and select the Search function.
- The application will prompt you to pair the fridge by pressing the set button on the fridge’s control panel.
- Once the set button has been activated, the fridge will be paired with your smart device and the application will switch to a control panel allowing you to control the fridge’s functions.
- SET
- Freezer zone current temperature
- Refrigerator zone current temperature
- Battery protection model: High/Medium/Low
- Turn ON/OFF the fridge
- Current-voltage
- Battery capacity (Battery is not supported on this model)
- Freezer zone temperature setting
- Refrigerator zone temperature setting
- TO ECO ( Energy-saving) / MAX(Fast cooling) mode switch
- Children’s Lock/ Unlock
- Celsisus / Fahrenheit switch
- Unpair the device and return to Search
- Note: Click the lock icon on the APP to lock/unlock the control panel on the fridge, if locked, the fridge can only be controlled by the APP.
- Please scan the OR code to download the APP
SPECIFICATIONS
Rated Voltage | DC 12/24V |
---|---|
Power Consumption | 60W |
Capacity | 65L |
Noise Emission | ≤45dB |
Temperature Range | 0-8°C(RE)/ -12~-20°C(FR) |
Climate Class | T/ST/N/SB |
Dimensions(WHD) | 430630470 mm |
N.W. | 19.06KG |
G.W. | 21.21KG |
WARRANTY INFORMATION
- Our product is guaranteed to be free from manufacturing defects for 3 years.
- If your product becomes defective during this period, Electus Distribution will repair, replace, or refund where a product is faulty; or not fit for the intended purpose.
- This warranty will not cover modified products; misuse or abuse of the product contrary to user instructions or packaging label; change of mind and normal wear and tear.
- Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and compensation for any other reasonably foreseeable loss or damage.
- You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and failure does not amount to a major failure.
- To claim a warranty, please contact the place of purchase. You will need to show a receipt or other proof of purchase. Additional information may be required to process your claim.
- Any expenses relating to the return of your product to the store will normally have to be paid by you.
- The benefits to the customer given by this warranty are in addition to other rights and remedies of the Australian Consumer Law concerning the goods or services to which this warranty relates.
- Electus Distribution
- Address 46 Eastern Creek Drive, Eastern Creek NSW 2766 Ph. 1300 738 555
Documents / Resources
|
Jaycar GH1676 Brass Monkey Single Door
Caravan
[pdf] Instruction Manual
GH1676 Brass Monkey Single Door Caravan, GH1676, Brass Monkey Single Door
Caravan, Monkey Single Door Caravan, Single Door Caravan, Door Caravan,
Caravan
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>