jaycar SL3954 RGB LED Light Strip Kit User Manual
- June 5, 2024
- Jaycar
Table of Contents
jaycar SL3954 RGB LED Light Strip Kit
Instructions for safety
Make sure you use the product perfectly and safely, please observe the instructions and warning on this manual. Operate cautiously and read these instructions carefully.
- For installation, try to avoid strong magnetic fields and high-pressure areas.
- Ensure that the wire is connected correctly and firmly in order to avoid short-circuit damage to parts and pose a fire hazard.
- Please install the controller in a well-ventilated place to ensure that the ambient temperature is moderate.
- Before using this product, please check the DC power and voltage meet the product’s technical requirements; positive and negative polarity is defined as consistent with the product.
- Prohibit live wiring, check to confirm wiring is correct, if no short-circuit, then power!
Specifications
- Input power: DC12V
- Output signal: SPI signal
- Max load current: 5A
- Drive IC number: 20—100pcs
- Output power: 60W (12V)
WARNING
KEEP BUTTON BATTERIES OUT OF REACH OF CHILDREN
- If swallowed a lithium button battery may lead to serious or fatal injury in as little as 2 hours, due to chemical burns and potential perforation of the esophagus.
- Non-lithium button batteries battery can cause serious injuries if it is swallowed or placed inside any part of the body.
- All button batteries must be kept away from children regardless if they are new or used.
- If you suspect your child has swallowed or inserted a button battery immediately call the 24-hour Poisons Information Centre on 13 11 26 (Australia) or 0800 764 766 (New Zealand) for fast, expert advice.
- If your child is having difficulty breathing contact 000 (Australia) or 111 (New Zealand).
- Dispose of used button batteries immediately and safely out of the reach of children. A battery can still be dangerous even when it can no longer operate the device.
- As soon as you have finished using a button battery, put sticky tape around both sides of it. This will make it harder for children to swallow the button battery and avoid the risk of the battery catching fire.
- Immediately dispose of button batteries immediately out of reach of children, or recycle using a child-resistant container and take used cells to your local battery collection centre.
Descriptions for panel and remote controller keys
| Icon | Name of keys | Description |
|---|---|---|
up/down
| Key in the static mode increases or decreases the LED brightness and IC number.
Keys in a dynamic mode increase/decrease speed.
|
OFF/ON
|
Turn on or off the LEDʼs
|
IC set
| Enter the IC configuration mode, and press this key all the lights are
bright white
|
Opening
| Static red, green, blue, yellow, green, purple, and white Monochromatic
water by the middle of the left / right push effect.
|
Closing
| The static model of red, green, blue, yellow, green, purple, and white monochrome water
From both sides to the middle closing effect.
---|---|---
| Colour selection| Red, green, blue, yellow, cyan, purple, and white is seven
kinds of monochromatic colours selected.
|
3 colour
| Press this key to red, green, and blue circulating flash, in a dynamic model
for flicker selection gradient colour.
|
7 colour
| Press this key for red, green, blue, yellow, cyan, purple, and white rainbow circulating flash
In a dynamic model for gradient flicker selection.
|
16colour
| Red, green, blue, yellow, cyan, purple, white, orange, deep yellow, light
yellow, light green, light blue, dark blue, sky blue, blue and purple,
magenta, choice of 16 colours
|
Water left
| The red, green, blue, yellow, cyan, purple, and white colours of each left
the water effect.
|
Water right
| The red, green, blue, yellow, cyan, purple, and white colours of each, right
of water.
| The left gradient of shining| From the left to the right of each IC 3
flashes light and gradually lights up all IC after all the extinguishing
effect.
|
Shining right gradient
|
From right to left each IC3 flashes and gradually light effect.
| Left total gradient of shining| From left to right each IC has 3 flashes lit
after quenching, lit by out all IC after all the light effect.
| Right full gradient flash out| From right to left each IC has 3 flashes lit,
lit by out all IC after all the light effect.
|
Meteor left
|
Meteor across the left ( dripping ) effect.
|
Meteor right
|
Meteor across the right( dripping ) effect.
|
water cycle
|
Around the water circulation effect.
|
Meteor
|
The meteor from left to right creates a circulation effect.
|
Gradient
| Press this key transition effect, and press the CS button to choose a
colour, 3 colours, 7 colours,16 colour gradient effect.
|
Flicker
|
Press this key to flicker effect, and CS, press button can select monochrome, tri-colour,7 colour, 16 colour flicker effect.
---|---|---
|
Automatic
|
All patterns of circulation.
- Key sequence description
Any pattern colour changes are needed to enter the static mode and choose a good colour after the choice of mode in order to achieve the desired results.
Troubleshooting
Failure
| ****
Analysis
| ****
Solution
---|---|---
No light
| ****
1. No power.
2. Reversed the polarity.
3. Wrong connection or poor contact.
| ****
1. Check the power
2. Make sure the polarity is right.
3. Re-check the wire connection.
The brightness of LED is not consistent
| 1. Input wire is too long to cause wire loss.
2. Diameter of the wire is too thin to cause wire loss.
3. Power overload.
| 1. Shorten wire or use a loop circuit.
2. Calculate the current, and then replace the thick wire.
3. Replace larger power.
4. Add a power amplifier
| 4. Controller overload.|
Distributed by:
Electus Distribution Pty. Ltd. 320 Victoria Rd, Rydalmere NSW 2116 Australia
www.electusdistribution.com.au
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>