HIKMICRO UD32821B Digital Night Vision Monocular User Guide

: June 10, 2024
: HIKMICRO

Table of Contents

HIKMICRO UD32821B Digital Night Vision Monocular
Specifications
Product Usage Instructions
FAQ
Appearance
Install Battery
Charge Device
More Operations
FCC STATEMENT
Maintenance
CONTACT
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

HIKMICRO UD32821B Digital Night Vision Monocular

HIKMICRO-UD32821B-Digital-Night-Vision-Monocular-
PRODUCT

Specifications

Model: HIKMICRO CHEETAH Series
Functionality: Digital Night Vision Monocular
Power Source: Battery
Interface: Type-C
Infrared Light: Yes
Adapter Compatibility: 38mm, 40mm, 50mm, 62mm

Product Usage Instructions

Rotate the battery compartment cover counterclockwise to open it.
Insert the battery following the marks for positive and negative terminals.
Securely close the battery compartment cover.
Align the red dot of the adapter with the eyepiece and insert it.
Rotate the locking ring to secure the adapter.
Rotate the locking ring counterclockwise to loosen it.
Gently remove the adapter.
Ensure the device is turned on and hotspot function is disabled.
Connect the device to a power adapter for charging via a Type-C cable.
Download the HIKMICRO Sight app from the App Store or Google Play.
Connect the device to the app for live view, settings, upgrades, and album access.

Refer to the user manual, accessible via QR code, for detailed operations.

FAQ

Q: How long should I charge the battery for the first use?
A: Charge the battery for more than 4 hours before initial use.
Q: How do I clean the thread of the battery compartment cover?
A: Use a cleaning cloth to ensure good conductivity if the thread gets dirty.

Appearance

Component & Interface (Page 1 – A)

No.	Component	Function
1	Lens Cover	Protect the lens.
2	Focus Ring	Adjust the focal length.
3	Power Key	● Press: standby mode/wake up device

● Hold: power on/off

4| Mode Key| Hold to switch display modes.
5| Wheel| ● Press: start/stop recording

● Hold: menu operation

HIKMICRO-UD32821B-Digital-Night-Vision-Monocular-FIG-1

Install Battery

HIKMICRO-UD32821B-Digital-Night-Vision-Monocular-FIG-2

Steps

Rotate the battery compartment cover counterclockwise to loosen and open it.
Insert the battery as the positive and negative marks indicate.
Rotate the battery compartment cover clockwise to until it is tight and locked.

Note

Take the battery away if you do not use the device for a long time.
The battery type is 18650 with a protection board. The battery size is 19 mm × 70 mm. The rated voltage is 3.6 VDC, and the battery capacity is 3200 mA.
Charge the battery for more than 4 hours before first use.
To ensure good conductivity, please use the cleaning cloth to clean the thread of the battery compartment cover if it gets dirty.

Install Adapter

HIKMICRO-UD32821B-Digital-Night-Vision-Monocular-FIG-3

Install an adapter if you want to connect a daylight scope to the device.

Steps

Make sure the red dot of the adapter aligns with the red dot of the eyepiece, and insert the adapter as arrow 1 shows.
Rotate the locking ring clockwise (as arrow 2 shows).

Note: Four diameters of adapters are selectable: 38 mm, 40 mm, 50 mm, and 62 mm.

Remove Adapter
Steps

Rotate only the locking ring counterclockwise, and make sure the device or other parts of the adapter are not rotated or moved.
Plug out the adapter after it is loosening.

Charge Device

HIKMICRO-UD32821B-Digital-Night-Vision-Monocular-FIG-4

Before You Start

Please turn on the device and make sure the hotspot function is disabled.

Steps

Lift the cover of the type-C interface.
Connect the device to the power adapter using a type-C cable to charge the device.

Connect to Mobile App

HIKMICRO-UD32821B-Digital-Night-Vision-Monocular-FIG-5

Search and download HIKMICRO Sight on the App Store (iOS System) or Google Play™ (Android System), or scan the QR code to download and install the App.
After connecting the device to the mobile App, you can view live view, set parameters, upgrade devices, and access albums on the App.

More Operations

Scan the QR code to obtain the user manual for more detailed operations.

Legal Information
© 2023 Hangzhou Microimage Software Co., Ltd. All rights reserved.

About this Manual
The Manual includes instructions for using and managing the Product. Pictures, charts, images and all other information hereinafter are for description and explanation only. The information contained in the Manual is subject to change, without notice, due to firmware updates or other reasons. Please find the latest version of this Manual on the HIKMICRO website (www.hikmicrotech.com/). Please use this Manual with the guidance and assistance of professionals trained in supporting the Product.

Trademarks Acknowledgement
and other HIKMICRO trademarks and logos are the properties of HIKMICRO in various jurisdictions. Other trademarks and logos mentioned are the properties of their respective owners.

LEGAL DISCLAIMER
TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THIS MANUAL AND THE PRODUCT DESCRIBED, WITH ITS HARDWARE, SOFTWARE AND FIRMWARE, ARE PROVIDED “AS IS” AND “WITH ALL FAULTS AND ERRORS”. HIKMICRO MAKES NO WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION, MERCHANTABILITY, SATISFACTORY QUALITY, OR FITNESS FOR A PARTICULAR PURPOSE. THE USE OF THE PRODUCT BY YOU IS AT YOUR OWN RISK. IN NO EVENT WILL HIKMICRO BE LIABLE TO YOU FOR ANY SPECIAL, CONSEQUENTIAL, INCIDENTAL, OR INDIRECT DAMAGES, INCLUDING, AMONG OTHERS, DAMAGES FOR LOSS OF BUSINESS PROFITS, BUSINESS INTERRUPTION, LOSS OF DATA, CORRUPTION OF SYSTEMS, OR LOSS OF DOCUMENTATION, WHETHER BASED ON BREACH OF CONTRACT, TORT (INCLUDING NEGLIGENCE), PRODUCT LIABILITY, OR OTHERWISE, IN CONNECTION WITH THE USE OF THE PRODUCT, EVEN IF HIKMICRO HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES OR LOSS. YOU ACKNOWLEDGE THAT THE NATURE OF THE INTERNET PROVIDES FOR INHERENT SECURITY RISKS, AND HIKMICRO SHALL NOT TAKE ANY RESPONSIBILITIES FOR ABNORMAL OPERATION, PRIVACY LEAKAGE OR OTHER DAMAGES RESULTING FROM CYBER-ATTACK, HACKER ATTACK, VIRUS INFECTION, OR OTHER INTERNET SECURITY RISKS; HOWEVER, HIKMICRO WILL PROVIDE TIMELY TECHNICAL SUPPORT IF REQUIRED.
YOU AGREE TO USE THIS PRODUCT IN COMPLIANCE WITH ALL APPLICABLE LAWS, AND YOU ARE SOLELY RESPONSIBLE FOR ENSURING THAT YOUR USE CONFORMS TO THE APPLICABLE LAW. ESPECIALLY, YOU ARE RESPONSIBLE, FOR USING THIS PRODUCT IN A MANNER THAT DOES NOT INFRINGE ON THE RIGHTS OF THIRD PARTIES, INCLUDING WITHOUT LIMITATION, RIGHTS OF PUBLICITY, INTELLECTUAL PROPERTY RIGHTS, DATA PROTECTION AND OTHER PRIVACY RIGHTS. YOU SHALL NOT USE THIS PRODUCT FOR THE ILLEGAL HUNTING OF ANIMALS, INVASION OF PRIVACY OR ANY OTHER PURPOSE THAT IS ILLEGAL OR DETRIMENTAL TO THE PUBLIC INTEREST. YOU SHALL NOT USE THIS PRODUCT FOR ANY PROHIBITED END-USES, INCLUDING THE DEVELOPMENT OR PRODUCTION OF WEAPONS OF MASS DESTRUCTION, THE DEVELOPMENT OR PRODUCTION OF CHEMICAL OR BIOLOGICAL WEAPONS, ANY ACTIVITIES IN THE CONTEXT RELATED TO ANY NUCLEAR EXPLOSIVE OR UNSAFE NUCLEAR FUEL-CYCLE, OR IN SUPPORT OF HUMAN RIGHTS ABUSES.
PLEASE FOLLOW ALL THE PROHIBITIONS AND EXCEPTIONAL CAVEATS OF ALL APPLICABLE LAWS AND REGULATIONS, IN PARTICULAR, THE LOCAL FIREARMS AND/OR HUNTING LAWS AND REGULATIONS. PLEASE ALWAYS CHECK NATIONAL PROVISIONS AND REGULATIONS BEFORE PURCHASE OR USE OF THIS PRODUCT. PLEASE NOTE THAT YOU MAY HAVE TO APPLY FOR PERMITS, CERTIFICATES, AND/OR LICENSES BEFORE ANY PURCHASING, SELLING, MARKETING AND/OR USING OF THE PRODUCT. HIKMICRO SHALL NOT BE LIABLE FOR ANY SUCH ILLEGAL OR IMPROPER PURCHASING, SELLING, MARKETING, AND END USES AND ANY SPECIAL, CONSEQUENTIAL, INCIDENTAL, OR INDIRECT DAMAGES ARISING THEREOF. IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE APPLICABLE LAW, THE LATTER PREVAILS.

These clauses apply only to the products bearing the corresponding mark or information

EU/UK Conformity Statement

This product and – if applicable – the supplied accessories too are marked with “CE” and comply therefore with the applicable harmonized European standards listed under Directive 2014/30/EU (EMCD), Directive 2014/35/EU (LVD), Directive 2011/65/EU (RoHS), Directive 2014/53/EU.
This product and – if applicable – the supplied accessories too are marked with “UKCA” and comply therefore with the following directives: Radio Equipment Regulations 2017, Electromagnetic Compatibility Regulations 2016, Electrical Equipment (Safety) Regulations 2016, the Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment Regulations 2012.

Frequency Bands and Power (for CE/UKCA)
The frequency bands and modes and the nominal limits of transmitted power (radiated and/or conducted) applicable to this radio device are the following: Wi-Fi 2.4 GHz (2.4 GHz to 2.4835 GHz), 20 dBm.

Directive 2012/19/EU (WEEE Directive): Products marked with this symbol cannot be disposed of as unsorted municipal waste in the European Union. For proper recycling, return this product to your local supplier upon the purchase of equivalent new equipment, or dispose of it at designated collection points. For more information see: www.recyclethis.info. According to the Waste Electrical and Electronic Equipment Regulations 2013: Products marked with this symbol cannot be disposed of as unsorted municipal waste in the United Kingdom. For proper recycling, return this product to your local supplier upon the purchase of equivalent new equipment, or dispose of it at designated collection points. For more information see: www.recyclethis.info.
Directive 2006/66/EC and its amendment 2013/56/EU (Battery Directive): This product contains a battery that cannot be disposed of as unsorted municipal waste in the European Union. See the product documentation for specific battery information. The battery is marked with this symbol, which may include lettering to indicate cadmium (Cd), lead (Pb), or mercury (Hg). For proper recycling, return the battery to your supplier or to a designated collection point. For more information see: www.recyclethis.info.

According to the Batteries and Accumulators (Placing on the Market) Regulations 2008 and the Waste Batteries and Accumulators Regulations 2009: This product contains a battery that cannot be disposed of as unsorted municipal waste in the United Kingdom. See the product documentation for specific battery information. The battery is marked with this symbol, which may include lettering to indicate cadmium (Cd), lead (Pb), or mercury (Hg). For proper recycling, return the battery to your supplier or to a designated collection point. For more information see: www.recyclethis.info.

FCC STATEMENT

Industry Canada ICES-003 Compliance
This device meets the CAN ICES-003 (B)/NMB-003(B) standards requirements.
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:

this device may not cause interference, and
this device must accept any interference, including interference that may cause undesired operation of the device.

Safety Instruction
These instructions are intended to ensure that the user can use the product correctly to avoid danger or property loss.
Laws and Regulations
Use of the product must be in strict compliance with the local electrical safety regulations.

Transportation

Keep the device in original or similar packaging while transporting it.
Keep all wrappers after unpacking them for future use. In case of any failure occurred you need to return the device to the factory with the original wrapper.
Transportation without the original wrapper may result in damage to the device and the company shall not take any responsibility.
Do not drop the product or subject it to physical shock. Keep the device away from magnetic interference.

Power Supply

The input voltage for the device should meet the Limited Power Source (5 VDC, 2 A) according to the IEC61010-1 or IEC62368 standard. Please refer to actual products and technical specifications for detailed information.
The power source should meet limited power source or PS2 requirements according to IEC 60950-1 OR ICE 62368-1 standard.
Use the power adapter provided by the qualified manufacturer. Refer to the product specification for detailed power requirements.
Make sure the plug is properly connected to the power socket.
DO NOT connect multiple devices to one power adapter, to avoid over-heating or fire hazards caused by overload.

Battery

Improper use or replacement of the battery may result in an explosion hazard. Replace with the same or equivalent type only. Dispose of used batteries in conformance with the instructions provided by the battery manufacturer.
Use the battery provided by a qualified manufacturer. Refer to the product specification for detailed battery requirements.
Make sure the battery temperature is between 0°C to 45°C (32°F to 113°F) when charging.
For long-term storage of the battery, make sure it is fully charged every half year to ensure the battery quality. Otherwise, damage may occur.
The built-in battery cannot be dismantled. Please contact the manufacturer for repair if necessary.
Batteries of improper size cannot be installed and may cause abnormal shutdown.
The battery cannot be charged with an external power source directly.
Confirm there is no flammable material within 2 m of the charger during charging.
DO NOT place the battery near the heating or fire source. Avoid direct sunlight.
DO NOT place the battery in the reach of children.
DO NOT swallow the battery to avoid chemical burns.

Maintenance

If the product does not work properly, please contact your dealer or the nearest service centre. We shall not assume any responsibility for problems caused by unauthorized repair or maintenance.
Wipe the device gently with a clean cloth and a small quantity of ethanol, if necessary.
If the equipment is used in a manner not specified by the manufacturer, the protection provided by the device may be impaired.
Clean the lens with a soft and dry cloth or wiping paper to avoid scratching it.
It is recommended to reboot the device every 2 hours when using it to ensure the device’s performance.

Using Environment

Make sure the running environment meets the requirements of the device. The operating temperature shall be -30 °C to 55 °C (-22 °F to 131 °F), and the operating humidity shall be 95% or less, no condensing.
Place the device in a dry and well-ventilated environment.
DO NOT expose the device to high electromagnetic radiation or dusty environments.
DO NOT aim the lens at the sun or any other bright light.
When any laser equipment is in use, make sure that the device lens is not exposed to the laser beam, or it may burn out.
Avoid equipment installation on vibratory surfaces or places subject to shock (neglect may cause equipment damage).

Emergency
If smoke, odour, or noise arises from the device, immediately turn off the power, unplug the power cable, and contact the service centre.