Ethnicraft 53061 Geometric Meeting Table Instruction Manual

Table of Contents

Specifications:
- Product Name: Geometric Meeting Table – Varnished Oak
- Product Code: 53061
- Dimensions: 313/140/76 cm Includes Cable Management

Parts to Assemble:
- Table Top x1
- Cable Management Box x2
- Leg x2
- Tools Required (Not Included):
- Flathead Screwdriver
- Phillips Screwdriver
Assembly Steps:
- A. Removing Metal Plates:
- Step 1: Use L Key 4 to loosen all screws on the apron.
- Step 2: Use L Key 5 to remove all screws from the metal plate. Do not throw away, screws will be used in Step C.
- Step 3: Slightly lift the apron and remove the metal plate.
- B. Installing Metal Plates to the Legs:
- Fit the screw into the barrel nut using a flathead screwdriver.
- Use a metal plate (4x), screw M8x50mm (8x), and L Key 5 to tighten. Tighten fully all screws.
- C. Installing the Legs:
- Step 1: Slightly lift the apron and ensure the leg fits firmly into the groove.
- Step 2: Use screw M6x60mm (2x), fit the screw into the barrel nut using a flathead screwdriver, and use L Key 4 to tighten but do not fully tighten.
- Step 3: Use screw M8x16mm (8x) and L Key 5 to tighten but do not fully tighten.
- D. Installing Cable Management Boxes:
- Use wood screw 4,5x20mm (12x) and tighten fully all screws using Phillips screwdriver.
- Cable management boxes can be installed in two directions as preferred.
- E. Re-Tighten All Screws:
- Use L Key 5 and L Key 4 to tighten all screws fully.
- F. Finish:
- Use L Key 4 to tighten all screws fully.

Q: Can one person assemble the table?
- A: It is advisable to assemble the table with at least three persons for safety and ease of assembly.

GEOMETRIC MEETING TABLE – VARNISHED OAK

CODE /DESCRIPTION
- 53061 /GEOMETRIC MEETING TABLE – VARNISHED OAK – WITH CABLE MANAGEMENT – 313/140/76

NOTE

CAREFULLY OPEN THE CARTON, REMOVE THE CONTENTS AND LAY IT OUT ON THE CARPET THE PACKAGING CARTON BOX OR OTHER PROTECTIVE SURFACE TO AVOID DAMAGE.
CHECK PACKAGE CONTENTS TO ENSURE ALL THE NECESSARY HARDWARE AND PARTS ARE RECEIVED UNDAMAGED.
DO NOT USE DAMAGED OR DEFECTIVE PARTS/HARDWARE. CONTACT ETHNICRAFT FOR ANY MISSING PARTS AND/OR HARDWARE.
READ THE ASSEMBLY INSTRUCTIONS BEFORE INSTALLATION AND CAREFULLY FOLLOW THE INSTRUCTION GIVEN.
SEEK A PROFESSIONAL’S ADVICE IF YOU ARE NOT FAMILIAR WITH THESE INSTALLATIONS OR HAVE ANY DOUBTS ABOUT THE SAFETY OF THIS INSTALLATION.
IT IS ADVISABLE TO DO THIS ASSEMBLY WITH MINIMUM OF 3 PERSONS.

$Ethnicraft-53061-Geometric-Meetin-Table-fig-1 $5$$

C CABLE MANAGEMENT BOX 2 pieces
- CODE /DESCRIPTION
- P4967 \CABLE MANAGEMENT BOX

(Included in package)

(Not Included in package)

$Ethnicraft-53061-Geometric-Meetin-Table-fig-1 $9$$

A. REMOVING METAL PLATES $Ethnicraft-53061-Geometric-Meetin-Table-fig-1 $10$$
B. INSTALLING METAL PLATES TO THE LEGS $Ethnicraft-53061-Geometric-Meetin-Table-fig-1 $11$$
C INSTALLING THE LEGS $Ethnicraft-53061-Geometric-Meetin-Table-fig-1 $12$$
D. INSTALLING CABLE MANAGEMENT BOXES $Ethnicraft-53061-Geometric-Meetin-Table-fig-1 $13$$
E RE-TIGHTEN ALL SCREWS $Ethnicraft-53061-Geometric-Meetin-Table-fig-1 $14$$
F FINISH $Ethnicraft-53061-Geometric-Meetin-Table-fig-1 $15$$