Thundercomm XDV1-0003 RF Board Unit Instruction Manual
- June 9, 2024
- Thundercomm
Table of Contents
RF module board Instructions for use
1 Packaging content
1. 1.nRF module board *1
2. Bubble bag + 1
2 Product appearance
Product specification
| product name | RF Board Unit |
|---|---|
| Product model specification | XDV1-0003 |
| product size | 34mm22mm3mm |
| dimensional tolerance | ±0.2mm |
| Product weight | 3g |
| product process | 1mm, FR 4, OSP, over hole cover oil |
| Electrostatic grade | NA |
| levels of protection | NA |
| working temperature | -25~65 degrees C |
| Storage temperature | -25~65 degrees C |
| Working humidity | 35%-95% |
| Store humidity | 35%-95% |
| working voltage | 1.8V |
| Power consumption | 50 mW (including master and RF parts) |
| Wireless frequency | 2.4GHz~2.480GHz |
Direction for use
- nRF module board Face up, the QFN connector is facing the QFN connector base at the glasses motherboard, press vertically.
- Take 2 screws and secure them with the main board.
Federal Communications Commission (FCC) Statement
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Warning: Changes or modifications made to this device not expressly approved
by Edan Instruments, Inc. may void the FCC authorization to operate this
device.
Note: The manufacturer is not responsible for any radio or TV interference
caused by unauthorized modifications to this equipment. Such modifications
could void the user’s authority to operate the equipment.
RF exposure statement:
The transmitter must not be co-located or operated in conjunction with any
other antenna or transmitter. This equipment complies with the FCC RF
radiation exposure limits set forth for an uncontrolled environment.
Integration instructions for host product manufacturers according to KDB 996369 D03 OEM Manual v01
2.2 List of applicable FCC rules
CFR 47 FCC PART 15 SUBPART C has been investigated. It is applicable to the
modular transmitter.
2.3 Specific operational use conditions
This module is stand-alone modular. If the end product will involve the
Multiple simultaneously transmitting condition or different operational
conditions for a stand-alone modular transmitter in a host, host manufacturer
have to consult with module manufacturer for the installation method in end
system.
2.4 Limited module procedures
Not applicable.
2.5 Trace antenna designs
Not applicable
2.6 RF exposure considerations
The device has been evaluated to meet general RF exposure requirement. The
device can be used in portable exposure condition without restriction.
2.7 Antennas
This radio transmitter has been approved by Federal Communications Commission
to operate with the antenna types listed below, with the maximum permissible
gain indicated. Antenna types not included in this list that have a gain
greater than the maximum gain indicated for any type listed are strictly
prohibited for use with this device if without further certify such as C2PC.
| Type | XDV1-0003 |
|---|---|
| Antenna type | PCB antenna |
| Frequency Range | 2.4GHz – 2.5 GHz |
| Antenna Gain | 1.61 dBi |
2.8 Label and compliance information
If the FCC identification number is not visible when the module is installed
inside another device, then the outside of the device into which the module is
installed must also display a label referring to the enclosed module. This
exterior label can use wording such as the following: “Contains Transmitter
Module FCC ID: 2AOHH-XDV1-0003” Or “Contains FCC ID:2AOHH-XDV1-0003”.
2.9 Information on test modes and additional testing requirements
Host manufacturer which install this modular with limit modular approval
should perform the test of radiated emission and spurious emission according
to FCC part 15C:15.247 and 15.209 requirement, only if the test result comply
with the requirement, then the host can be sold legally.
2.10 Additional testing, Part 15 Subpart B disclaimer
Host manufacturer is responsible for compliance of the host system with module
installed with all other applicable requirements for the system such as Part
15 B.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>