MIGRO 154 Smart Wi-Fi Controller User Manual
- June 3, 2024
- MIGRO
Table of Contents
MIGRO 154 Smart Wi-Fi Controller
Smart Wi-Fi Controller
ATTENTION !!!
Connect to Wi-Fi Network Indoors Prior to Installation
Ensuring your MIGRO Smart Wi-Fi Controller is functioning prior to field installation is required by the manufacturer. Environmental and application specific conditions may cause communication error and manufacturer. Environmental and application specific conditions may cause communication error and a bench test will ensure that the equipment is functioning properly. Connect a 120VAC Power Supply to the System and perform the pairing steps to ensure connection. (see pairing instructions)
WARNING
- This Smart Box system should be installed by a LICENSED ELECTRICIAN. Turn Power off at main panel before servicing this switch or the equipment it controls.
- Wiring must be in accordance with all national and local electrical code requirements.
- This Smart Box Enclosure does not provide grounding between conduit connectors.
Installation Instructions
Your Wi-Fi control system must be installed and maintained as described in this guide to ensure reliable and safe operation. Confirm the voltage and current draw of your connected load to the control output is consistent with the design specifications of this product and that your application will not exceed the maximum load capacity listed.
System Features
Wi-Fi ENABLED CONTROLS
Use mobile apps as well as Google and Alexa to your system on/off or scheduling
MANUAL ON MODE
“Manual ON” mode will give you the ability to run your system regardless of
the Wi-Fi control status.
BEYOND SCHEDULING
Use the Google, Alexa and IFTTT capabilities to control your systems by
weather, workflow Geo-fencing, and others
OVERRIDE OFF MODE
Additional Data:
- Power Supply: 120 VAC
- Relay: DPST & 3P
- Security: WEP/WPA-PSK/WPA2-PSK
- FCC Part 15 IEEE 802.11 b/g/n
- Wi-Fi Frequency: 2.412-2.48GHz
This mode provides users with great safety protection. The OFF mode will remain OFF regardless of Wi-Fi controls.
Contact Load Ratings
- Normally Open
- CH1- 2 Pole : 50A Resistive 40A Inductive
- CH2- 2 Pole : 50A Resistive 40A Inductive
- CH3- 2 Pole : 50A Resistive 40A Inductive
- CH4- 2 Pole : 50A Resistive 40A Inductive
-
CONDUIT FITTING
Install the Conduit Fitting provided (or one provided by others) in the desired location ensuring wire clearance within the enclosure. -
ANTENNA
Install the Antenna provided on to the threaded connector located on the outside of the enclosure. -
MOUNT TO DESIRED LOCATION
Place and mount the enclosure to your desired location using the supplied hardware. The brackets are to be mounted to the back exterior of the enclosure with the wall flanges facing out. (See Image 1) -
WIRE THE SYSTEM
Wire in accordance with the national and local electrical codes (see wiring diagram).After wiring is complete, turn circuit power on and test your MIGRO Mi-Fi Swit®ch.
Manual Override:
Momentarily press the push button located on the Soloff smart WIFI switch module.
WIRING & PAIRING
- L = Line
- N = Neutral
- T = Load Terminal
System Features
Wi-Fi ENABLED CONTROLS
Use mobile apps as well as Google and Alexa to your system on/off or
scheduling
BEYOND SCHEDULING
Use the Google, Alexa and IFTTT capabilities to control your systems by
weather, workflow Geo-fencing, and others.
PAIRING TO WI-FI NETWORK
To Connect your MIGRO ® Smart Wi-Fi Controller to your app and Wi-Fi Network,
please refer to the ewe link instructions or Scan the QR Code
below.
TIPS
- Install the antenna as high as possible, clear from obstructions or metal structures.
- Ensure that your WIFI Router is placed as high as possible to maximize range and coverage.
WEB LINK
https://migromifi.com/manuals/migro-pool-fi-smart-switch-120vac/
Find other Wireless Control Solutions at www.MIGRO.com
as well as compatible accessories
MIGRO WIRELESS SOLUTIONS 01/2022
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>