Bissell 1699/ 8905 Series ProHeat ClearView User’s Guide

Bissell 1699/ 8905 Series ProHeat ClearView User's Guide

Thanks for buying a BISSELL ProHeat ™ ClearView ®

We’re glad you purchased a BISSELL ProHeat ClearView heated formula deep cleaner. Everything we know about floor care went into the design and construction of this complete, high-tech home cleaning system.

Your ProHeat ClearView is well made, and we back it with a limited one-year warranty. We also stand behind it with a knowledgeable, dedicated Consumer Services department, so, should you ever have a problem, you’ll receive fast, considerate assistance.

My great-grandfather invented the floor sweeper in 1876.Today, BISSELL is a global leader in the design, manufacture, and service of high quality homecare products like your ProHeat Clearview.

Thanks again, from all of us at BISSELL.

Mark J. Bissell
President and Chief Executive Officer

IMPORTANT SAFETY INSTRUCTIONS

When using an electrical appliance, basic precautions should be observed, including the following:
Read all instructions before using your PROHEAT ™ CLEARVIEW. ™

WARNING : To reduce the risk of fire, electric shock, or injury:

• Do not immerse.
• Use only on surfaces moistened by cleaning process.
• Always connect to a properly grounded outlet.
• See Grounding Instructions.
• Unplug from outlet when not in use and before conducting maintenance or troubleshooting.
• Do not leave machine when it is plugged in
• Do not service machine when it is plugged in
• Do not use with damaged cord or plug
• If appliance is not working as it should, has been dropped, damaged, left outdoors, or dropped into water, have it repaired at an Authorized Service Center.
• Do not expose to rain, store indoors
• Do not pull or carry by cord, use cord as a handle, close door on cord, pull cord around sharp corners or edges, run appliance over cord, or expose cord to heated surfaces
• Do not carry the appliance while in use
• Unplug by grasping the plug, not the cord
• Do not handle plug or appliance with wet hands
• Do not put any object into appliance openings, use with blocked opening, or restrict air flow
• Do not expose hair, loose clothing, fingers or body parts to openings or moving parts
• Do not pick up hot or burning objects
• Do not pick up flammable or combustible materials (lighter fluid, gasoline, kerosene, etc.) or use in the presence of explosive liquids or vapor
• Do not use appliance in an enclosed space filled with vapors given off by oil base paint, paint thinner, some moth proofing sub stances, flammable dust, or other explosive or toxic vapors
• Do not pick up toxic material (chlorine bleach, ammonia, drain cleaner, gasoline, etc.)
• Do not modify the 3-prong grounded plug
• Do not allow to be used as a toy
• Do not use for any purpose other than described in this User’s Guide
• Do not operate the appliance unless the belt door is securely assembled in the location provided
• Do not unplug by pulling on the cord.
• Use only manufacturer’s recommended attachments
• Use only cleaning products formulated by BISSELL for use in this appliance
• Keep openings free of dust, lint, hair, etc.
• Do not point attachment nozzle at people or animals.
• Keep appliance on a level surface
• Turn off all controls before unplugging
• Unplug before attaching the Turbo Brush ™
• Be extra careful when cleaning stairs
• Close attention is necessary when used by or near children

SAVE THESE INSTRUCTIONS.

THIS MODEL IS FOR HOUSEHOLD USE ONLY.
Commercial use of this unit voids the manufacturer’s warranty.

GROUNDING INSTRUCTIONS
This appliance must be connected to a grounded wiring system. If it should malfunction or break down, grounding provides a safe path of least resistance for electrical current, reducing the risk of electrical shock. The cord for this appliance has an equipment-grounding conductor and a grounding plug. It must only be plugged into an outlet that is properly installed and grounded in accordance with all local codes and ordinances.

WARNING : Improper connection of the equipment-grounding conductor can result in a risk of electrical shock. Check with a qualified electrician or service person if you aren’t sure if the outlet is properly grounded. DO NOT MODIFY THE PLUG. If it will not fit the outlet, have a proper outlet installed by a qualified electrician. This appliance is designed for use on a nominal 120-volt circuit, and has a grounding attachment plug that looks like the plug in the drawing above. Make certain that the appliance is connected to an outlet having the same configuration as the plug. No plug adapter should be used.

How to Use this Guide

WARNING :
Do Not plug in your cleaner until you have completely assembled it per the following instructions and are familiar with all instructions and operating procedures.

This User’s Guide has been designed to help you get the utmost satisfaction from your BISSELL ProHeat ClearView. You’ll find assembly and operating instructions, safety precautions, as well as maintenance and troubleshooting instructions. Please read this Guide thoroughly before assembling your Deep Cleaner.

Pay particular attention to the product diagram, assembly instructions, and part names. Locate and organize all parts before assembly. Familiarize yourself with the parts and where they go. Following this User’s Guide will greatly enhance your ability to get the most performance from your BISSELL ProHeat ClearView for many years.

Your ProHeat ClearView comes in three,
easy to assemble components.
Upper Handle
Lower Handle
Tool Caddy
The only thing you will need to assemble your cleaner is a Phillips head screwdriver.

How To Put It Together

Refer to Assembly Diagram on page 4

1. Slide Upper Handle onto Lower Handle.
2. Feed bundled power cord through Tool Caddy from caddy’s flat side.
3. Align Upper Handle holes and Tool Caddy holes.
4. Place hex nut into back of Tool Caddy and hold in place. Insert bolt from front to back turning into the hex nut until snug. Do not over tighten. Repeat for the second bolt and hex nut.
5. Insert 2 screws into lower 2 holes. Turn until snug.
6. Snap tools into Storage on the Tool Caddy as shown in figure 6.
7. Wrap Power Cord and Flex Hose as shown in figure 7.

ProHeat ClearView assembly is now complete.

Special Features of Your BISSELL ProHeat ™ ClearView ®

The BISSELL SmartClean ® System
The ProHeat ClearView is a home cleaning system that automatically mixes hot tap water with the BISSELL advanced cleaning formula and heats the solution as it is applied to the carpet. The combination of heated cleaning solution, powered brush and suction provide a safe & effective method of cleaning.

SmartTemp ®

Temperature control automatically heats the cleaning solution as it is being applied to the carpet (*) to safely optimize cleaning effectiveness.

1. The Power Switch controls power to the machine; both switches must be ON for SmartTemp to work.
2. The SmartTemp Switch is found on the back of the handle next to the Power Switch. You may choose not to use the
   SmartTemp feature if you are cleaning delicate wool or oriental rugs.
   *SmartTemp heats the cleaning solution for carpet and bare floor application only. It does not heat solution sprayed through the accessory tools.
3. The SmartTemp Ready Light indicates when the heater is ON. The heater should be turned on two minutes before cleaning, to become fully warmed up and ready to clean. The Smart Temp Ready Light is found on the front of the handle where it is easy to see while you clean
4. SmartTemp increases the water temperature 25° and will not allow it to exceed 180°.

SmartMix ®

Provides custom control for each cleaning job.

1. Lift the SmartMix concentrate bottle up and out of the machine base.

2. Turn the bottle over so that the valve cap is in an upward position. Unscrew the valve cap and fill the bottle to the mark with BISSELL Deep Cleaning Formula.

3. Replace the valve cap turning until snug.

4. Replace SmartMix concentrate bottle.
   Note : If bottle leaks, check for proper positioning of o-ring and straw.

5. Choose the SmartMix setting that fits the cleaning job.
   Water Rinse – use for gentle cleaning or for the final rinse after cleaning.
   Normal – automatically provides the best mix of water and concentrate for most cleaning jobs.
   High Traffic – automatically mixes the right amount of water and concentrate to dissolve tough grime and heavy soil. Note : Residual cleaning materials left in carpet from other products may cause excessive foaming when picked up. If foam is overflowing tank, move SmartMix dial to “Water Only” position until the condition stops.
   Note : Both the SmartMix Bottle and the clean water tank must have liquid in them in order for the machine to spray. If one tank is empty, the machine will temporarily lose its prime and not apply either cleaning solution or water only.
   Important : If you are using the WATER RINSE setting, fill the Smart Mix bottle with water also!

Tip : Deep Cleaning stairs and high traffic areas on a regular basis can prolong carpet life.

WARNING :
To reduce the risk of injury, be extra careful when cleaning stairs. Make sure machine is secure and level.

DirtLifter ® PowerBrush

The powered brush roll at the floor nozzle is designed to enhance cleaning performance. The bristle pattern lifts out the deep down dirt while gently grooming carpet fibers. The floating suspension self-adjusts to all carpet heights and protects your carpet if you leave the power switch ON. When the machine handle is in the fully upright position, CarpetSaver automatically raises the brush off the carpet.

WARNING :
To reduce the risk of fire, use only BISSELL Deep Cleaning Formula in your ProHeat ClearView. Use of cleaning formulas which contain lemon or pine oil may damage this appliance and void warranty. Chemical spot cleaners or solvent based soil removers should not be used. These products may react with the plastic materials used in your ProHeat ClearView, causing cracking or pitting.

Tank-in-Tank

Our Tank-in-Tank system is designed with a Bladder inside for clean water. As you clean, the Bladder will empty. Dirty water collects in the tank outside the Bladder.

1. Step on handle release to lay the machine handle down out of the way.

2. Lift the Tank-in-Tank handle. The handle locks the lid in place.

3. Carry it like a bucket to fill at the sink.
   Note : You may notice hair and debris deposits on the carpet that were loosened by the brushing action (especially with newer carpets that have never been deep cleaned before). This debris should be picked up and thrown away. Debris that deposits in the Brush Belt should be cleaned between uses to keep the Belts running free.

4. Set the tank down and rotate the handle forward to unlatch the lid. Lift off and set the lid aside.

5. Find the mouth of the Bladder and fill to the bottom of the neck with clean hot tap water. *Do not boil or microwave
   water as it can destroy the Bladder.
   Note : Fill the Bladder with clean hot tap water only.

6. Replace the Tank Lid matching the lid and tank edges. Handle must be in the forward position to reinstall.

7. Rotate the handle to the carrying position to re-latch the lid.

8. Replace tank in machine base, seating firmly in place.

9. Rotate handle back down to the latched position.
   Note : Both the SmartMix Bottle and the clean water tank must have liquid in them in order for the machine to spray. If one tank is empty the machine will not apply either cleaning solution or water.
   Important : If you are using the WATER RINSE setting, fill the SmartMix bottle with water also!

When It’s Time to Empty Tank-in-Tank

1. Remove the Tank-in-Tank – follow steps 1 and 2 on page 8.

2. Carry the Tank-in-Tank, like a bucket, to the sink where you will dispose of the dirty water.

3. Remove Tank Lid by rotating handle forward to unlatch lid and lifting lid off tank.

4. Pour out dirty water.

5. After each use, remove and rinse the lint screen located on the Tank Lid.
   A. Remove Tank Assembly from unit.
   B. Remove Tank Lid.
   C. Remove any debris caught in Lint Screen.
   D. Reinsert Lint Screen on Tank Lid. The screen will click into place
   E. Replace Tank Lid.
   F. Reinsert Tank Assembly into unit.

6. Refill with clean tap water as above, steps 5 through 9 on page 8, and refill the SmartMix bottle with BISSELL Deep Cleaning Formula as necessary.

7. When the cleaning job is complete, rinse out the Tank-in-Tank by rinsing clean water between the Bladder and tank.

8. Return Tank-in-Tank to the machine, following steps 6 through 9 (on page 8).

9. Refer to the Maintenance section, page 18 for the final cleanup.

Tip:
A special red float device in the tank will cause the cleaner to stop removing solution from the carpet and the motor sound will rise in pitch to let you know the dirty water tank is full.

Tip:
Thorough vacuuming before deep cleaning will prevent early clogging of lint trap.

The Flow Indicator

This is located on the machine base. It spins when the trigger is pressed to indicate that the machine is applying cleaning solution to the floor. It will stop spinning to indicate that the SmartMix bottle or Bladder needs to be refilled, or when the trigger is released. Flow Indicator does not spin when set to Tool setting.

ReadyTools Dial

This provides above floor cleaning with the flip of a switch. Just choose the cleaning tool, attach to the flex hose and ProHeat Clearview is ready to clean upholstery, stairs or more.*

Set the dial to Floor Cleaning when cleaning carpets or bare floors or set it to Tools/PreTreat when using the flex hose attachments or for pre-treating floors. SmartTemp heats the cleaning solution for carpet and bare floor application only. It does not heat solution sprayed through the accessory tools.

TurboBrush ®

(Available on select models only)

Assembly

Unplug cleaner from outlet before attaching TurboBrush. Attach TurboBrush to the flex hose by pressing tool onto the grip/trigger until button snaps into hole. Make certain tool is securely in place.

Use

1. Move the TurboBrush switch to the “BRUSH” position. This activates the brush.
2. Place the tool directly on the soiled surface. Apply downward pressure on the tool and pull towards you while pulling trigger to spray cleaning solution.
3. Release the spray trigger and move the switch to the “SUCTION” position. Vacuum the area until no more cleaning solution can be removed.
4. Repeat steps 1-3 until no more dirt can be removed.
   Caution : Do not overwet.

When You’re Done

1. Disconnect the TurboBrush from the flex hose by pushing down on the button lock and pulling straight off.
2. Once removed from the Flex Hose, the TurboBrush can be cleaned.
   A. Move the switch to the “SUCTION” position.
   B. Rinse under running water.
   C. Check spray nozzle for dirt. If necessary, clean with a soft bristle brush.
   D. Replace TurboBrush in the special storage location on the handle front.(on select models only)

Operations

Before You Clean Carpets

1. Plan activities to give carpet time to dry.
2. Remove easily moved furniture from the room (chairs, lamps, coffee tables, etc).
3. Vacuum thoroughly to pick up loose debris and pet hair before using the ProHeat ClearView.
4. Plan your cleaning route to leave an exit path. It is best to begin cleaning in the corner farthest from your exit.

Machine Preparation

1. Set up the machine following instructions in The Features section, pages 6-11.
2. Use a BISSELL Advanced Cleaning Formula in the SmartMix tank.When cleaning carpets, stairs or upholstery, use clean water in the SmartMix Tank for gentle cleaning or rinsing.
3. Choose the SmartMix setting to match the cleaning job.
4. Set the ReadyTools switch to either Tools/PreTreat or Floor Cleaning.

PreTreating

Pretreating is recommended to improve cleaning effectiveness for heavily soiled carpet in high traffic areas such as entryways and hallways:

1. Set the SmartMix dial to High Traffic.
2. Set ReadyTools dial to PreTreat.
3. Plug into a proper outlet and turn on both the Power and Smart Temp Switches.
4. While pressing the trigger slowly make several passes over the area to be cleaned. Caution Do not overwet.
5. Turn the machine Power Switch OFF and let the BISSELL Advanced Cleaning Formula dissolve the tough soil for 1-2 minutes before continuing.

Tip :
Try pretreating stairs or entry ways with BISSELL Tough Stain PreCleaner. Then deep clean with the SmartMix ® dial set on High Traffic.

Carpet Cleaning

ATTENTION BERBER CARPET OWNERS :
Some Berber Carpets have a tendency to fuzz with wear. Repeated strokes in the same area with an ordinary vacuum or deep cleaner may aggravate this condition. Please see Stain Removal instructions on page 13.

1. Plug into a proper outlet and turn the Power and the SmartTemp switches ON. Wait two minutes for the heater to warm up before beginning to clean.

2. While pressing the trigger, make one slow forward wet pass and another one back. Let the SmartTemp heated formula and DirtLifter Powerbrush do the work for you.Caution: Do not overwet.
   Note : Take care not to run over loose objects or edges of area rugs. Stalling brush may result in premature belt failure.

3. Release the trigger and make one slow forward and back pass over the same area to remove any residual dirty water.

4. Repeat cleaning passes until solution being pulled up appears clean.

5. Continue passes without pressing the trigger until you can’t see any more water being pulled up.
   Note : Both the SmartMix and the clean water tank must have liquid in them in order for the machine to spray.If one tank is empty the machine will not apply either cleaning solution or water only.

6. After cleaning, you may want to turn the SmartMix dial to Water Only to give your carpeting a final rinse.This will ensure thorough removal of embedded dirt loosened by the Advanced Deep Cleaning Formula. Advanced Deep Cleaning Formulas contains an anti-resoiling agent that helps your carpets repel dirt and keeps them looking good longer.

7. When the cleaning job is complete refer to the Maintenance section for machine cleanup and storage instructions on page 18

Stain Removal

Do Not Delay! Failure to attend to an accident soon after it occurs may cause it to set and become permanent.
Before treating any stain, follow these pre-treatment steps:

1. Blot up liquids with an absorbent cloth or paper towels. White materials are recommended because certain dyes may bleed and make the stain worse.

2. Gently scrape up semi-solids with a spoon or spatula. Do not use a knife or other utensil with sharp edges because it could damage the carpet or upholstery.

3. If the area has dried, remove the remaining semi-solids and residue with a sweeper or vacuum.

4. Be sure to pre-test any spot removal solutions or chemicals on an inconspicuous area first. This is extremely important; different dyes and materials could be damaged or discolored by a cleaning solution. If such a change should occur, try a different solution or call a professional. If cleaning on Berber Carpet gently run your machine over a hidden area. If no fuzzing occurs, continue cleaning in soiled area.
   Use one of the following methods to Preclean the stain:

5. Using BISSELL Tough Stain Precleaner ™ , generously spray the area with the formula. Gently work the solution with a clean cloth or towel into the area using light strokes from the edges of the stain to the center. When your cloth reaches the center of the stain, gently pinch it in an upward motion. Make sure to turn and change your cloth frequently and do not rub the stain. You may repeat this process several times.
   or
   Use your BISSELL deep cleaner as a Precleaner. With one of the tools attached to hose, set the Ready Tools dial to Pretreat and the Smart Mix dial to the High Traffic setting. Spray the area with solution and allow the Deep Cleaning formula to penetrate for 3-5 minutes.

6. Once the Precleaning is complete, use the attached tool to gently scrub the stain with back and forth strokes.

7. Allow to dry. Some difficult stains may require a second treatment.

How to Clean Upholstery and Small Areas

Important – Check Upholstery Tags:

1. Check manufacturer’s tag before cleaning. “W” or “WS” on the tag means you can use your ProHeat ClearView. If the tag is coded with “X” or “S” (with a diagonal strike through), or says “Dry Clean Only,” do not proceed. Do not use on velvet or silk. If manufacturer’s tag is missing or not coded, check with your furniture dealer.
2. Check for colorfastness in an inconspicuous place.
3. If possible, check upholstery stuffing. Colored stuffing may bleed through fabric when wet.
4. Plan activities to give upholstery time to dry.
5. Vacuum thoroughly to pick up loose debris and pet hair. Use a vacuum with a brush attachment and a crevice tool to clean in fabric folds and tufts.

Machine Preparation

1. Set up the machine following instructions in the Features section, pages 6-11.
2. Use BISSELL Advanced Cleaning Formulas in SmartMix tank.
3. Set the ReadyTools dial to Tools or PreTreat.

• SmartTemp heats the cleaning solution for carpet and bare floor application only. It does not heat solution sprayed through the accessory tools. 4. Set SmartMix Dial to Normal.

Tip : Deep cleaning carpeting and upholstery with BISSELL Multi-Allergen Removal Formula™ with Scotchgard™ protection regularly can reduce dust and allergens in your home.

Cleaning Technique

1. Choose the 4” Small Area Tool, the Tough Stain Brush, or the Spraying Crevice Tool and connect to the Flex Hose.

2. Plug into a proper outlet and turn Power Switch ON.

3. While pressing the trigger, slowly move the spraying tool back and forth over the soiled surface. Release the trigger to suction soiled water.

4. Continue to clean soiled area, working in small sections, until no more dirt can be removed.
   Caution : Do not overwet.

5. When the cleaning job is complete refer to the Maintenance section for machine cleanup and storage instructions on page 18.

Cleaning Bare Floors

The Bare Floor Tool is included in select models only. If your ProHeat CleaView did not come so equipped, you may contact BISSELL Consumer Services at www.bissell.com or 1-800-237-761 to order one. The Bare Floor Tool provides effective cleaning for linoleum, vinyl, and tile floors.
Caution : Do not use on hardwood floors.

1. Use BISSELL Floor Cleansing Formula.
2. Vacuum or sweep thoroughly to pick up loose debris and pet hair.
3. Remove easily moved furniture from the room (chairs,tables,etc.).
4. Plan your cleaning route to leave an exit path.
5. Plan activities to allow 30 minutes for the floor to dry completely.

Attach the Bare Floor Tool

1. Step on the handle release to lay the machine handle down.
2. Remove the Tank-in-Tank from the machine base.
3. Lift the machine base to expose the underside of the Floor Nozzle.
4. Attach Bare Floor Tool to Floor Nozzle with long Tab to the right side (ReadyTools side) of the Floor Nozzle.
5. First attach left side (short Tab) catching tab over nozzle edge.
6. Gently bend long Tab (right side) outward to easily snap over edge of clear nozzle on left.

Machine Preparation

1. Set up machine following instructions in the Features section, pages 6-11. Be sure to thoroughly rinse out any remaining Fiber Cleansing Formula from the SmartMix bottle to prevent slippery linoleum, vinyl, and tile floors. Use BISSELL Floor Cleansing Formula in the SmartMixtank.
2. Check ReadyTools Dial – it should be set on Floor Cleaning.
3. Choose the SmartMix setting to match the cleaning job.
4. Plug into a proper outlet and turn Power Switch ON. Turn SmartTemp switch ON. The SmartTemp Ready Light illuminates and ProHeat ClearView is ready to clean.

Bare Floor Cleaning Technique

1. Slowly move the machine nozzle with Bare Floor Tool forward and back over soiled surface one time while pressing the trigger. Caution: Do not overwet.
2. Repeat the motion without pressing the trigger using the Bare Floor Tool to squeegee and suction up the dirty water.
3. Repeat steps 1 and 2 backing along the exit path.
4. Allow about 30 minutes for the floor to dry completely.
5. When the cleaning job is complete refer to the Maintenance/Storage section on page 18.
6. To remove Bare Floor Tool gently bend long tab (right side) outward and pull tool down away from nozzle. Rinse thoroughly, dry and store.

Routine Maintenance

1. Turn Power and SmartTemp switches OFF.

2. Unplug power cord from the outlet and coil around Power Cord Quick Release.

3. Remove and rinse tools in clean, running water, dry and replace in the Tool Caddy.

4. Coil Flex Hose around storage brackets on Tool Caddy.

5. Remove Tank-In-Tank, dispose of dirty water. See Features section, page 8-9.

6. Rinse out Tank-In-Tank and replace on the machine; Clean out lint trap.

7. Clean out the Flow Indicator Filter each time it is used to ensure best cleaning performance. Unscrew the Flow Indicator Cap, lift out the Red Rotor and White Filter. Rinse all three parts in tap water. Replace the filter and rotor. Replace the Flow Indicator Cap; turn until snug, do not over-tighten.

8. Wipe all exterior surfaces with a soft cloth.

9. Store cleaner upright in a protected, dry area.
   Note : ProHeat ClearView uses water and must not be stored where there is a danger of freezing. Freezing will damage internal components and void the warranty.

10. When carpet is dry, vacuum again to remove hair and fuzz the ProHeat ClearView may have loosened.

WARNING : To reduce the risk of fire, electric shock or injury unplug from outlet before servicing.

Tip : SmartMix Bottle may be stored with concentrate ready for your next cleaning job. Make sure dial is turned to the Water Rinse Setting when storing.

Pump Belt Replacement

To Remove Broken Pump Belt

1. Turn the machine off and unplug from the wall outlet.
2. Step on the release pedal and recline the handle down onto floor (see illustration).
3. Remove Tank-In-Tank and SmartMix tanks. Set them aside (see illustration).
4. Remove Belt Access Door located near the Floor Cleaning/Tools switch by inserting a flat head screwdriver into the slot nearest to the handle and gently prying the access door off (see illustration).
5. Turn the machine onto its side so the belt access area is facing upward (see illustration).
6. On the bottom of the machine, near the belt access area, is a red retainer plate that holds the black brush arm and brush in place. Using a Phillips head screwdriver remove the screw that holds the red retainer plate in place. Set red retainer plate and Phillips head screw aside (see illustration).
7. Remove the black brush arm that holds the brush in place. Set the black brush arm aside (see illustration).
8. Remove the “toothed” brush belt from the brush then from the red pump pulley. Set the “toothed” brush belt and brush aside.
9. Locate and remove broken pump belt.

To Install the Replacement Pump Belt

1. With the unit still on its side, loop one end of the replacement pump belt around the red pump pulley and then the other end around the silver motor shaft (see illustration). Do not twist the replacement pump belt.
2. Re-install the toothed brush belt first onto the red pump pulley and then onto the toothed end of the brush (see illustration).
3. Re-install the brush into the base of unit.
4. Place the black brush arm onto the brush and slide black brush arm into base of unit. The black brush arm and brush should slide easily into original position(see illustration).
5. Re-install the red retainer plate and Phillips head screw (see illustration).
6. Using your finger, gently spin the replacement pump belt on the silver motor shaft. If assembled correctly, the replacement pump belt should rotate freely around the silver motor shaft and drive pulley without obstruction. The brush should also rotate freely when the silver motor shaft is turned.
7. Turn the machine right side up and replace the Tank-In-Tank, SmartMix Tank and Belt Access Door (see illustration).)
8. Assembly is now complete.
   If you have any questions, or are having trouble installing your replacement pump belt, please call BISSELL Consumer Services at 1-800-237-7691.

Troubleshooting

BISSELL Consumer Services

For information about repairs or replacement parts, or questions about your warranty, call:

BISSELL Consumer Services 1-800-237-7691
Monday – Friday 8 a.m. — 9 p.m. EST
Saturday 9 a.m. — 5 p.m. EST

Or write :
BISSELL HOMECARE, INC
PO Box 3606
Grand Rapids MI 49501
ATTN: Consumer Services

Or visit the BISSELL website – www.bissell.com
When contacting BISSELL, have model number of unit available.
Please record your Model Number:
Please record your Purchase Date:

NOTE : Please keep your original sales receipt. It provides proof of date of purchase in the event of a warranty claim. See “About Your Warranty” on page 24 for details.
Please do not return this product to the store.

Replacement parts – BISSELL ProHeat ClearView

About Your Warranty

This warranty gives you specific legal rights, and you may also have other rights which may vary from state to state. If you need additional instruction regarding this warranty or have questions regarding what it may cover, please contact BISSELL Consumer Services by E-mail, telephone, or regular mail as described below.

Limited One Year Warranty
Subject to the *EXCEPTIONS AND EXCLUSIONS identified below, upon receipt of the product BISSELL Homecare Inc. will repair or replace (with new or remanufactured components or products),at BISSELL’s option, free of charge from the date of purchase by the original purchaser, for one year any defective or malfunctioning part.

See information below on “If your BISSELL product should require service”.

This warranty applies to product used for personal, and not commercial or rental service. This warranty does not apply to routine maintenance components such as filters, belts, or brushes. Damage or malfunction caused by negligence, abuse, neglect, unauthorized repair, or any other use not in accordance with the User’s Guide is not covered.

If your BISSELL product should require service:
Contact BISSELL Consumer Services to locate a BISSELL Authorized Service Center in your area. If you need information about repairs or replacement parts, or if you have questions about your warranty, contact BISSELL Consumer Services.

Website or E-mail :
www.bissell.com
Use the “Customer Services” tab.

Or Call :
BISSELL Consumer Services
1-800-237-7691
Monday – Friday 8 a.m.- 9 p.m.EST
Saturday 9 a.m.- 5 p.m. EST

Or write :
BISSELL Homecare Inc.
PO Box 3606
Grand Rapids MI 49501
ATTN: Consumer Services

BISSELL HOMECARE, INC. IS NOT LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES OF ANY NATURE ASSOCIATED WITH THE USE OF THIS PRODUCT. BISSELL’S LIABILITY WILL NOT EXCEED THE PURCHASE PRICE OF THE PRODUCT.

Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you.

*EXCEPTIONS AND EXCLUSIONS FROM THE TERMS OF THE LIMITED WARRANTY

THIS WARRANTY IS EXCLUSIVE AND IN LIEU OF ANY OTHER WARRANTIES EITHER ORAL OR WRITTEN. ANY IMPLIED WARRANTIES WHICH MAY ARISE BY OPERATION OF LAW, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE,ARE LIMITED TO THE ONE YEAR DURATION FROM THE DATE OF PURCHASE AS DESCRIBED ABOVE.

Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you.

Bissell 1699/ 8905 Series ProHeat ClearView User’s Guide – Download [optimized]
Bissell 1699/ 8905 Series ProHeat ClearView User’s Guide – Download

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>