Bissell 1844 Series Barkbath Portable Dog Bath User Guide

: June 8, 2024
: Bissell

Barkbath Portable Dog Bath

IMPORTANT SAFETY INSTRUCTIONS

READ ALL INSTRUCTIONS BEFORE USING YOUR PORTABLE DOG BATH SYSTEM.
When using an electrical appliance, basic precautions should be observed, including the following:

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY:

Use only warm tap water. Do not use heated water.
Connect to a properly grounded outlet only. See grounding instructions. Do not modify the 3-prong grounded plug.
Do not leave appliance when it is plugged in. Unplug from outlet when not in use and before servicing.
Do not expose to rain. Store indoors.
Do not allow to be used as a toy. Close attention is necessary when used by or near children.
Do not use for any purpose other than described in this User’s Guide. Use only manufacturer’s recommended attachments.
Do not use with damaged cord or plug. If appliance is not working as it should, has been dropped, damaged, left outdoors, or dropped into water, have it repaired at an authorized service center.
Do not pull or carry by cord, use cord as a handle, close a door on cord, or pull cord around sharp edges or corners. Do not run appliance over cord. Keep cord away from heated surfaces.
Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.
Do not handle plug or appliance with wet hands.
Do not put any object into openings. Do not use with any opening blocked; keep openings free of dust, lint, hair, and anything that may reduce air flow.
Keep hair, loose clothing, fingers, and all parts of body away from openings and moving parts.
Turn off all controls before plugging or unplugging appliance.
Use extra care when cleaning on stairs.
Do not use to pick up flammable or combustible materials (lighter fluid, gasoline, kerosene, etc.) or use in areas where they may be present.
Do not use appliance in an enclosed space filled with vapors given off by oil base paint, paint thinner, some moth proofing substances, flammable dust, or other explosive or toxic vapors.
Do not use to pick up toxic material (chlorine bleach, ammonia, drain cleaner, etc.).
Do not pick up anything that is burning or smoking, such as cigarettes, matches, or hot ashes.
Keep appliance on a level surface.
Do not carry the appliance while in use.
Do not immerse appliance in water or place in area where splashing may occur.
Liquid must not be directed towards equipment containing electrical components.

WARNING: Improper connection of the equipment-grounding conductor can result in a risk of electrical shock. Check with a qualified electrician or service person if you aren’t sure if the outlet is properly grounded. DO NOT MODIFY THE PLUG. If it will not fit the outlet, have a proper outlet installed by a qualified electrician. This appliance is designed for use on a nominal 120-volt circuit, and has a grounding attachment plug that looks like the plug in the illustration. Make certain that the appliance is connected to an outlet having the same configuration as the plug. No plug adapter should be used with this appliance.

GROUNDING INSTRUCTIONS

Grounded-Outlets-Grounding-
Pin

This appliance must be connected to a grounded wiring system. If it should malfunction or break down, grounding provides a safe path of least resistance for electrical current, reducing the risk of electrical shock. The cord for this appliance has an equipment-grounding conductor and a grounding plug. It must only be plugged into an outlet that is properly installed and grounded in accordance with all local codes and ordinances.

SAVE THESE INSTRUCTIONS FOR FUTURE USE

This model is for household use only. Commercial use of this unit voids the manufacturer’s warranty.

Thanks for buying a BISSELL BarkBath™!
We love pets, so we’re excited to share one of our newest innovative pet products with you. We want to make sure your BarkBath™ dog bathing system works as well in years to come as it does today, so this guide includes tips on usage, maintenance and, if there is a problem, basic troubleshooting.
Once your dog is acclimated to the cleaner and you’ve got a bathing area prepared, a few simple assembly steps are all it takes to get started!

What’s In The Box?

box

Before You Get Started

Before started

Helpful Tips to Get Ready:

Always use a BISSELL no-rinse dog shampoo.
If your dog has long hair, brush your pet’s hair before bathing.
When selecting an area to bathe your dog, choose a place where your pet feels comfortable and safe. Usual choices include the kitchen, utility room, garage or family room.
Lay down a separate blanket or towel where you will be bathing your dog.
When placing the cleaner on the floor, be sure to set it on the microfiber mat. Not only is the mat highly absorptive to protect your floor, it will help to dampen the sound for your dog.
Keep the unit away from walls and cabinets to facilitate sound reduction.

Noise-Sensitive or Anxious Dog?

Some dogs are sensitive to loud noises, or are not fans of vacuums or other loud appliances. Here are some quick training tips to help your dog have a great experience with this new bathing method.

Training Steps—Phase 1

Place the unit in a room where you plan to bathe your dog. Leave the unit turned off and allow the dog to become accustomed to it.
With the unit turned off, have the dog walk over to the unit and use the spray nozzle as a “comb” to brush the dog. This will allow the dog to associate good feelings with the unit.
Praise your dog and offer a treat.

Training Steps—Phase 2

With the dog out of the room, turn the unit on. Leave the unit on and offer your dog a treat.
Turn the unit off.
Repeat phase one above.

Training Steps—Phase 3

Turn the unit on, have your dog enter the room and give the dog a treat.
With the unit on, and without pulling the trigger to release water, “comb” your dog’s fur with the spray nozzle.
Turn the unit off and offer a treat.

Training Steps—Phase 4

Turn the unit on. Have your dog enter the room.
Comb a small section of your dog’s fur with the unit on and pull the trigger in quick, short bursts to acclimate your pet to feeling the solution on their skin.
Once the area is fully wetted and water extracted, your dog’s bath is complete. Praise your pet and offer a treat.

Getting to Know Your Cleaner

product info

Carry Handle
Power On/Off Switch
Dirty Water Tank
Flex Hose Clip
Flex Hose Storage Bracket
Quick Release™ Cord Wrap
Power Cord
Clean Water Tank
Flex Hose Connector Release
Shampoo Tool Connector
Rinse/Shampoo Switch
Shampoo Reservoir
Spray Nozzle
Nozzle Spray Trigger
Mesh Plate
Nozzle Height Selection
Removable Face Plate
Removable Face Plate Screw

BISSELL® No-Rinse Dog Shampoo

Always use genuine BISSELL No-Rinse Dog Shampoo. Other shampoos may harm the machine and will void the warranty.

NOTICE: Do not use dish soap, traditional dog or human shampoos and/or conditioners because they are too thick and may damage the machine. Use only BISSELL No-Rinse Dog Shampoo in your Portable Dog Bath System. Use of shampoos or soaps which contain lemon or pine oil may damage this appliance and void the warranty. These products may react with the plastic materials used in your cleaner, causing cracking or pitting.

Assembly

WARNING: Do not plug in your Portable Dog Bath System until you are familiar with all the safety and operating instructions.

Assembly

Slide the back plate of the flex hose clip into the opening on the front of the unit. You will hear a “click” when it is locked in place.
Take the flex hose storage bracket and slide the lower plate into the opening on the back of the unit. Make sure the screw hole lines up.
Insert screw and tighten with a screwdriver.
Wrap the flex hose around unit and place hose grip into bracket. Turn bracket latch clockwise to lock in place.

Preparing Your Cleaner

WARNING: To reduce the risk of injury to your pet, do not boil or microwave water. Use only warm tap water.

Prepare cleaner

Remove the clean water tank by lifting it straight up and then away from the unit.
Flip the tank so the black cap is on top and unscrew. Pull up to remove cap assembly from tank.
To ensure your pet has a nice bathing experience, use warm-to-the-touch tap water to the fill line on your clean water tank. Replace the cap before returning the tank to the machine.
Replace the clean water tank by lining up the grooves on the clean water tank with the vertical guides on the side of the unit. Gently slide it down into position.
Before connecting the bathing tool, you will need to prime the system. Place the unit on a high, flat surface (such as a table or counter top).
Plug the unit in and press the power switch to ON ( I ) position.
Hold the flex hose end over the microfiber mat or towel and press the trigger at the end of the flex hose for 15-20 seconds to allow water to dispense.
Turn the unit OFF, pressing the power switch to ( O ) OFF position.

Attaching the Bathing Tool

NOTICE: Dish soap, traditional dog or human shampoos and/or conditioners should not be used as they may be too thick and may damage the machine. Use only BISSELL No-Rinse Dog Shampoo in your Portable Dog Bath System. Use of shampoos or soaps which contain lemon or pine oil may damage this appliance and void the warranty. These products may react with the plastic materials used in your cleaner, causing cracking or pitting.

Attaching Bath tool

Locate the bathing tool and BISSELL No-Rinse Dog Shampoo.
Unscrew the cap to the shampoo reservoir to unattach it from the bathing tool.
Holding the tool right side up, add BISSELL No-Rinse Dog Shampoo to the shampoo reservoir.
Align the screw cap with the tabs of the reservoir opening and twist shut.
Holding the tool horizontally on a flat surface (such as a table or counter top), attach the bathing tool to the cleaner by inserting the flex hose connector into the shampoo tool connector. You will hear a “click” when it locks into place.
Prime the tool by pointing the nozzle at the microfiber mat and pressing and holding the spray trigger for 15-20 seconds to allow solution to dispense.

NOTE: The “factory setting” of the spray nozzle is optimized for use on most hair lengths/types with the exception of thick/heavy/dual and longer coated dogs.
TIP: Since every dog is unique, first start by adding a small amount of BISSELL No-Rinse Dog Shampoo to reservoir. Continue to add more shampoo as needed to effectively clean your dog.

Bathing Your Dog

WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT IMMERSE APPLIANCE IN WATER OR PLACE IN AREA WHERE SPLASHING MAY OCCUR.

NOTICE: Always use genuine BISSELL No-Rinse Dog Shampoo. Other shampoos may harm the machine and will void the warranty.

Recommended areas for bathing your dog:
• Kitchen
• Utility Room
• Garage
• Family Room bathing dog

Place the base unit on the microfiber mat on the floor of the area where you are going to bathe your dog. The microfiber mat will help dampen the sound for your pet.
Lay down a separate blanket or towel in the area where you will be bathing your dog.
OPTIONAL: The spray nozzle is optimized for use on most hair types, however, using a screwdriver you can remove the screw from the plate of the bathing tool and pull off to expose longer nozzles for use
on thick, heavy or longer coated dogs.
Plug in the unit and press the power switch to ON ( | ) position.
Set the Rinse/Shampoo switch to the desired setting. For Shampoo, the reservoir will dispense a mixture of shampoo and water; for Rinse, it will dispense just water.
Prime the system by pointing the nozzle at the microfiber mat and pressing and holding the spray trigger for 15-20 seconds to allow solution to dispense.
Place the tool directly onto the dog’s coat before pressing and holding the spray trigger to release the shampoo/water onto your dog’s coat.
Press and hold the spray trigger while gently stroking the nozzle of the bathing tool downwards, following the fall of the dog’s coat.
Release the spray trigger and use “drying strokes” to suction up moisture from the dog’s coat. Repeat as needed.
Spray shampoo/water on the microfiber towel and hand clean delicate areas such as the dog’s face and paws.
As a final step, coat should be air or towel-dried as needed.

NOTE: The Dog Bathing Tool is always extracting dirty water. The trigger dispenses the shampoo and/or water. While pressing the trigger, it also continues extracting dirty water.

Emptying the Dirty Water Tank

WARNING: To reduce the risk of electric shock, turn power OFF and disconnect plug from electrical outlet before performing maintenance or troubleshooting. Dirty tank

Turn power switch to the OFF (O) position and unplug power cord from outlet.
Lift up the dirty water tank lever and pull up to remove the tank from the unit. Carry the tank upright to avoid spilling before emptying.
Empty and rinse the dirty/collection tank after each use, OR when dirty water reaches the indicated maximum fill line.
Place tank back in unit, and press down on tank lever to lock it in place.

Cleaning Your BarkBath™ After Use

WARNING: To reduce the risk of electric shock, turn power OFF and disconnect plug from electrical outlet before performing maintenance or troubleshooting. cleaning bark bath

Turn power switch to the OFF (O) position and unplug power cord from outlet.
Remove and rinse out the dirty water tank following instructions in the “Emptying the Dirty Water Tank” section.
Press release button and disconnect flex hose from the dog bathing tool by pulling straight out. (DO NOT twist tool to remove.)
Once removed from flex hose, keep tool elevated to avoid dripping water on floor and rinse clean under running water.
Flip tool to release water into sink. While holding the tool in the air and reservoir in the sink, press the trigger to assure all water empties from the hose.
Check spray nozzle for accumulated dirt or debris. If necessary, clean with soft bristle brush.
You may disassemble the spray nozzle for cleaning as needed. Removing the faceplates will expose longer spray nozzles.
Be sure all pieces are completely dry before returning to base unit and before storage.

Storing Your BarkBath™

WARNING: To reduce the risk of electric shock, turn power OFF and disconnect plug from electrical outlet before performing maintenance or troubleshooting.

NOTICE: To reduce the risk of a leaking condition, do not store unit where freezing may occur. Damage to internal components may result. storing
bark bath

Wipe all surfaces with a soft cloth and machine wash microfiber towel and mat, making sure all items are clean and dry.
Wrap power cord around the cord wrap on the back of the base.
Wrap flex hose around the base of the unit and secure the end into the flex hose storage bracket.
Store unit in a protected dry area at room temperature.
Place bathing tool, BISSELL no-rinse dog shampoo, microfiber towel and mat in the storage bag and store with cleaner.

Troubleshooting

WARNING: To reduce the risk of electric shock, turn power switch off and disconnect plug from electrical outlet before performing maintenance or troubleshooting checks.

Problem

|

Possible causes

|

Remedies

---|---|---

Reduced or no suction

|

Hair build-up on suction nozzle

|

Clean as needed while washing dog

Using tool too far from pet

|

Contact dogs coat and periodically let go of spray trigger to allow for drying strokes

Area under dirty water tank has sand, hair, or debris

|

Remove dirty water tank and clean any sand or debris off inlet on the base of the machine and the gasket on the bottom of dirty water tank

Dirty tank full or not seated properly

|

Empty tank and replace, snapping top lid into place

Clog or build-up in hose

|

Suction hot water up to clear hose

Loose hose connection

|

Ensure machine hose is locked in place into the bathing tool

Reduced spray or

not spraying

|

Solution or water tank is empty

|

Check and refill both water and bathing tool solution tanks

Spray tip clogged

|

Rinse tool with warm water and use soft bristle brush on spray tips

Loose hose connection

|

Ensure machine hose is locked in place into the bathing tool. Hold trigger until water comes out

Lost prime

|

Turn unit off; Refill the water tank (and shampoo tank if needed), turn unit on and hold the trigger for 20-30 seconds until spray resumes

Leaking

|

Dirty water tank gasket not in place or damaged

|

Place gasket in correctly (notched); If damaged, replace gasket

Loose hose connection

|

Ensure machine hose is locked in place into the bathing tool; Hold trigger until water comes out

Damage or torn hose

|

Have an authorized technician repair unit

Bathing tool solution cap not in place

|

Make sure the solution cap on the bathing tool is in place with a gasket in the cap

No power to unit

|

Outlet not working

|

Test outlet with a small appliance like a cell phone charger, and use another outlet if needed

Fuse/breaker to outlet tripped

|

Reset the breaker

Dog still dirty or smells

|

Difficult Odor (ie. skunk)

|

Rewash or consult a professional for very difficult odors

Shampoo not foaming

|

Shampoo is designed to not be foamy

|

Continue using appropriate no rinse shampoo that is not foamy

Shampoo is not flowing

|

Not using a BISSELL no-rinse dog shampoo

|

Always use a BISSELL no-rinse dog shampoo

Rinse/Shampoo switch not fully engaged

|

Make sure switch is securely selected to the desired function

Lost prime

|

Turn unit off; Refill the water tank (and shampoo tank if needed), turn unit on and hold the trigger for 20-30 seconds until spray resumes

Warranty

This warranty gives you specific legal rights, and you may also have other rights which may vary from state to state. If you need additional instruction regarding this warranty or have questions regarding what it may cover, please contact BISSELL Consumer Care by e-mail or telephone as described below.

Limited One-Year Warranty

Subject to the *EXCEPTIONS AND EXCLUSIONS identified below, upon receipt of the product BISSELL will repair or replace (with new or remanufactured components or products), at BISSELL’s option, free of charge from the date of purchase by the original purchaser, for one year any defective or malfunctioning part.

See information below on “If your BISSELL product should require service”.

This warranty applies to product used for personal, and not commercial or rental service. This warranty does not apply to fans or routine maintenance components such as filters, belts, or brushes. Damage or malfunction caused by negligence, abuse, neglect, unauthorized repair, or any other use not in accordance with the User’s Guide is not covered.

BISSELL IS NOT LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES OF ANY NATURE ASSOCIATED WITH THE USE OF THIS PRODUCT. BISSELL’S LIABILITY WILL NOT EXCEED THE PURCHASE PRICE OF THE PRODUCT.
Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you.

*EXCEPTIONS AND EXCLUSIONS FROM THE TERMS OF THE LIMITED WARRANTY

THIS WARRANTY IS EXCLUSIVE AND IN LIEU OF ANY OTHER WARRANTIES EITHER ORAL OR WRITTEN. ANY IMPLIED WARRANTIES WHICH MAY ARISE BY OPERATION OF LAW, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED TO THE FIVE YEAR DURATION FROM THE DATE OF PURCHASE AS DESCRIBED ABOVE.
Some states do not allow limitations on how long an implied warranty lasts so the above limitation may not apply to you.

NOTE: Please keep your original sales receipt. It provides proof of date of purchase in the event of a warranty claim.

Service

If your BISSELL product should require service:
Contact BISSELL Consumer Care to locate a BISSELL Authorized Service Center in your area.
If you need information about repairs or replacement parts, or if you have questions about your warranty, contact BISSELL Consumer Care.

Website:www.BISSELL.com
E-mail:www.BISSELL.com/email-us
Call: BISSELL Consumer Care
1-800-237-7691
Monday – Friday 8am – 10pm ET Saturday 9am – 8pm ET Sunday 10am – 7pm ET

Please do not return this product to the store.
Other maintenance or service not included in the manual should be performed by an authorized service representative.
For any questions or concerns, BISSELL is happy to be of service. Contact us directly at 1-800-237-7691.

Bissell 1844 Series Barkbath Portable Dog Bath User Guide – Download [optimized]
Bissell 1844 Series Barkbath Portable Dog Bath User Guide – Download