Bissell 1716 Series Spotlifter Powerbrush User Guide

: June 8, 2024
: Bissell

Table of Contents

Bissell® 1716 Series Spotlifter® Powerbrush User Guide
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Bissell® 1716 Series Spotlifter® Powerbrush User Guide

Bissell® 1716 Series Spotlifter® Powerbrush

Important Safety Instructions

Read all instructions before using your portable DEEP CLEANER.

When using an electrical appliance, basic precautions should be observed, including the following:

WARNING

To reduce the risk of fire, electric shock, or injury:

Use only BISSELL cleaning products intended for use in this machine to prevent internal component damage. See the Cleaning fluid section of this guide.
Connect to a properly grounded outlet only. See grounding instructions. Do not modify the 3-prong grounded plug.
Do not leave appliance when it is plugged in. Unplug from outlet when not in use and before servicing.
Do not expose to rain. Store indoors.
Do not immerse. Use only on surfaces moistened by cleaning process.
Do not allow to be used as a toy. Close attention is necessary when used by or near children.
Do not use for any purpose other than described in this User’s Guide. Use only manufacturer’s recommended attachments.
Do not use with damaged cord or plug. If appliance is not working as it should, has been dropped, damaged, left outdoors, or dropped into water, have it repaired at an authorized service center.
Do not pull or carry by cord, use cord as a handle, close a door on cord, or pull cord around sharp edges or corners. Do not run appliance over cord. Keep cord away from heated surfaces.
Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.
Do not handle plug or appliance with wet hands.
Do not put any object into openings. Do not use with any opening blocked; keep openings free of dust, lint, hair, and anything that may reduce air flow.
Keep hair, loose clothing, fingers, and all parts of body away from openings and moving parts.
Turn off all controls before plugging or unplugging appliance.
Use extra care when cleaning on stairs.
Do not use to pick up flammable or combustible materials (lighter fluid, gasoline, kerosine, etc.) or use in areas where they may be present.
Do not use appliance in an enclosed space filled with vapors given off by oil base paint, paint thinner, some moth proofing substances, flammable dust, or other explosive or toxic vapors.
Do not use to pick up toxic material (chlorine bleach, ammonia, drain cleaner, etc.).
Do not pick up anything that is burning or smoking, such as cigarettes, matches, or hot ashes.
Keep appliance on a level surface.
Do not carry the appliance while in use.

SAVE THESE INSTRUCTIONS FOR FUTURE USE

This model is for household use only. Commercial use of this unit voids the manufacturer’s warranty.

WARNING

Improper connection of the equipment-grounding conductor can result in a risk of electrical shock. Check with a qualified electrician or service person if you aren’t sure if the outlet is properly grounded. DO NOT MODIFY THE PLUG. If it will not fit the outlet, have a proper outlet installed by a qualified electrician. This appliance is designed for use on a nominal 120-volt circuit, and has a grounding attachment plug that looks like the plug in the illustration. Make certain that the appliance is connected to an outlet having the same configuration as the plug. No plug adapter should be used with this appliance.

GROUNDING INSTRUCTIONS

This appliance must be connected to a grounded wiring system. If it should malfunction or break down, grounding provides a safe path of least resistance for electrical current, reducing the risk of electrical shock. The cord for this appliance has an equipment-grounding conductor and a grounding plug. It must only be plugged into an outlet that is properly installed and grounded in accordance with all local codes and ordinances.

Product View

Removable Brush Cartridge with Dual PowerBrushes
Spray Nozzle
Belt Cover Door
Power Switch
Spray Trigger
Solution Tank
Solution Tank Release Tabs
Power Cord
Collection Tank
Circuit Interrupting Device (C.I.D.)

Cleaning fluid

Keep plenty of genuine BISSELL 2X Portable Cleaning Formula on hand so you can clean whenever it fits your schedule. Always use genuine BISSELL deep cleaning formulas. Non-BISSELL cleaning solutions may harm the machine and will void the warranty.

WARNING

To reduce the risk of fire and electric shock due to internal component damage, use only BISSELL cleaning fluids intended for use with the deep cleaner.

WARNING

Use only BISSELL 2X compact formulas in your cleaner. Use of cleaning formulas which contain lemon or pine oil may damage this appliance and void the warranty. Chemical spot cleaners or solvent-based soil removers also should not be used. These products may react with the plastic materials used in your cleaner, causing cracking or pitting.

Product Features

WARNING

Do not plug in your portable deep cleaner until you are familiar with all instructions and operating procedures.

Solution tank
Holds BISSELL 2X Spot & Stain formula and water.

Collection tank
Collects dirty water and solution. You will need to remove the solution tank before you can remove the collection tank.

Spray trigger
Dispenses water and solution.

Solution tank release tabs
Gently press in to remove the clean/solution Tank.

Circuit Interrupting Device (C.I.D.)
Because you will be using this product in wet environments, such as bathrooms, we have equipped this unit with this added safety feature. The C.I.D. shuts off the product in potentially hazardous situations. The C.I.D. has test (white) and reset (red) buttons which should be operated each time the product is plugged in.

Removable Brush Cartridge with Dual PowerBrushes
Double the cleaning action to lift and remove stains and dirt. Removable for easy cleaning.

Operations

Filling the solution tank

Remove the solution tank by gently pressing the quick release tabs on the solution tank and sliding the tank off of the unit.
Open the tank by unscrewing and removing the cap. Add water and formula* to the indicated fill lines on the solution tank.

NOTE: Your Spot Lifter PowerBrush includes an 8 oz. trial size formula. 3. Replace the cap before placing the tank back on the unit.

Pre-treating

To aid in the removal of tough, stubborn stains, pre-treating the stain may be necessary.

Hold the unit above the area to be cleaned. Using the manual trigger spray, apply a sufficient amount of water and solution to the stain.
Wait 3-5 minutes before cleaning.

Cleaning

WARNING

Keep spray away from face. Failure to do so may result in personal injury.

Plug in the unit.
Turn the power switch to the “ON” position. ( I )
While holding the Spot Lifter PowerBrush above the area to be cleaned, apply water and formula by pressing the manual trigger spray, dispensing fluid to the soiled/stained area.
Brushing and suction can be done separately, based on how you hold and use the unit.
To Use The Dual PowerBrushes Only:
Tilt the unit forward slightly, placing both brushes in contact with the carpet. The flat surface of the brush cartridge should be parallel to the surface being cleaned.
Tips
• You may also spray water and formula, with the manual trigger spray, while the unit is turned on and you are using the dual PowerBrushes then suction to clean.
• Check upholstery stuffing before cleaning. Colored stuffing may bleed through the fabric when it becomes wet.
• When cleaning a vertical surface (ie: chair back, auto interior, etc.) begin with a completely empty collection tank.
• If a significant amount of water and solution remains in the clean tank, your unit can be stored with liquid in the clean tank.
• If you do not have the Brush Cartridge in all the way, the Dual PowerBrushes will not rotate. Firmly push the cartridge in place, while listening for the “snap” to assure proper placement.
WARNING
Keep spray away from face. Failure to do so may result in personal injury
For Suction Only:
Tilt the unit forward, pressing the front of the Spot Lifter PowerBrush firmly against the surface area to be cleaned, lifting the brushes up off the surface. Pull toward you to remove the soil and cleaning solution.
Note: Step #4 may be repeated until no more dirty water is removed or until the area to be cleaned meets your satisfaction.
Check the collection tank and empty the tank if it is full (See To empty the collection tank, below).
If the Spot Lifter PowerBrush stops spraying, turn off the unit and check the cleaning solution level in the solution tank. Refill if needed. Never run the unit without water or cleaning solution.

Spot cleaning upholstery

Important
Check the manufacturer’s tag before cleaning upholstery. “W” or “WS” on the tag means you can use your SpotLifter. If tag is coded with an “S” (with diagonal strikethrough), or says “Dry Clean Only,” do not proceed. If manufacturer’s tag is missing or not coded, check with your furniture dealer.

Check manufacturer’s tag before cleaning. “W” or “WS” on the tag means you can use your Spot Lifter PowerBrush. If tag is coded with an “S” (with diagonal strike-through) or states “Dry Clean Only”, do not proceed.
If manufacturer’s tag is missing or not coded, check with your furniture dealer.
If possible, check upholstery stuffing. Colored stuffing may bleed through fabric when wet.

Maintenance & Care

Machine care

WARNING

To reduce the risk of electric shock, turn power switch off and disconnect plug from electrical outlet before performing maintenance or troubleshooting checks.

To empty the collection tank

Begin by removing the solution tank. Gently press the quick release tabs on the solution tank and slide the tank off of the unit.
Grasp the collection tank and pull to remove.
While at the sink, remove the tank cap by unscrewing and lifting out.
Empty the tank. Rinse the collection tank with warm water.
Replace cap by turning to the right, until snug.
Slide the collection tank into the unit. Replace the solution tank.

Note: If a significant amount of water and formula remains in the solution tank, you may leave it in the solution tank for your next cleaning task.

To clean the dual powerbrush

WARNING

To reduce the risk of electric shock, turn power switch off and disconnect plug from electrical outlet before performing maintenance or troubleshooting checks.

NOTE: Make sure the Power Switch is in the “OFF” ( O ) position and the unit is unplugged.

Firmly grasp the brush cartridge from the side of the unit and pull out from the unit.
To remove any debris that may have collected around the dual PowerBrushes, rinse the brush cartridge under warm water.
Replace the brush cartridge into the unit by gently guiding the cartridge in the unit. Once it is in place, firmly “snap” the brush cartridge in place.

NOTE: Do not attempt to remove or insert the brush cartridge while the unit is running. This will damage your unit.

Storage

Store in a dry area, at room temperature to avoid freezing.

To replace the powerbrush belt

WARNING

To reduce the risk of fire, electric shock or injury, unplug from outlet before servicing.

If the belt should break, to replace:

Remove the screw in the belt cover using a Phillips Screwdriver.
Remove the broken belt.
Replace the new belt over the 2 belt gears.
Replace the belt cover door.

Troubleshooting

WARNING

To reduce the risk of electric shock, turn power switch off and disconnect plug from electrical outlet before performing maintenance or troubleshooting checks.

Troubleshooting